Instruction/ maintenance manual of the product BLM430 Makita
Go to page of 8
Model No. Description PRODUCT C ONCEPT AND MAIN APPLICA TIONS BLM430, LM430D 430mm Cordless Lawn Mower 460 (18-1/8) Dimensions: mm (inch) Width (W) Height (H) Length (L) 1,490 (58-3/4) 1,450 (57) 950 .
R epair P 2 / 8 [2] ASSEMBLY/ DISASSEMBLY [2]-1. Handle section [1] NECESSARY REPAIRING TOOLS Description Code No. Use for Round bar for Arbor 11-50 (1) Lift and remove Rear bag section from Deck. ( Fig. 1 ) While holding Handle section (Lower pipe, Upper pipe complete, etc.
R epair P 3 / 8 [2] ASSEMBLY/ DISASSEMBLY [2]-1. Handle section (cont.) Assemble Handle section in the reverse order of disassembly. Note : • Face the top of Lever to the upper side when assembling Lever to Switch lever.
R epair P 4 / 8 [2] ASSEMBLY/ DISASSEMBLY [2]-2. Motor section (1) Remove Blade. (2) Pull Lock lever to release the locking of Battery cover complete, and then open Battery cover complete. ( Fig. 11 ) Remove the hinge of one side carefully, and separate it from Cowling.
R epair P 5 / 8 [2] ASSEMBLY/ DISASSEMBLY [2]-3. Change lever section (1) Remove Cowling. (Refer to the previous page.) (2) Shift Change lever to the position of grass cutting height 75mm. (3) Detach the hook of Tension spring 16 from the projection of Deck using long-nose pliers.
R epair P 6 / 8 [2] ASSEMBLY/ DISASSEMBLY [2]-4. Wheels (1) Pull Front wheel caps straight out of Front wheels. ( Fig. 22 ) Remove Rear wheel caps in the same way. (2) Remove M8 Collared hex nuts and Front wheels from Front shaft. ( Fig. 23 ) Separate Rear wheels from Rear shaft in the same way.
R epair C ircuit diagram W iring diagram P 7 / 8 [2] ASSEMBLY/ DISASSEMBLY [2]-5. Connecting rod, Shafts (cont.) Assemble each wheel section in the reverse order of disassembly. Distinguish Front shaft from Rear shaft by the white paint. ( Fig. 30 ) Connect Lead wires as drawn below.
W iring diagram (cont.) Fig. D-3 P 8 / 8 Terminal Connect Flag receptacles as drawn above. Be careful to the directions. All Connectors, Line filters and Controller must be set in place using ribs on Deck as drawn above. Be careful not to put any Lead wires on ribs drawn above.
An important point after buying a device Makita BLM430 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Makita BLM430 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Makita BLM430 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Makita BLM430 you will learn all the available features of the product, as well as information on its operation. The information that you get Makita BLM430 will certainly help you make a decision on the purchase.
If you already are a holder of Makita BLM430, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Makita BLM430.
However, one of the most important roles played by the user manual is to help in solving problems with Makita BLM430. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Makita BLM430 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
