Instruction/ maintenance manual of the product 8411D Makita
Go to page of 16
Cordless Hammer Drill Capacities Steel Wood Wood screw Concrete 10 mm (3/8”) 21 mm I13/16”) 71;4m: ~~~~1~~ 10 mm (3/8”) Equipped with electric brake MODEL 8411D MODEL 8411DW With Fast Charger No load speed (RPM) High LOW 0 ~ 1,150 0 -- 370 INSTRUCTION MANUAL 0 ~ 12,700 1.
I M PO RTANT SAFETY I N STRUCTI 0 N S (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don’t carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in.
IMPORTANT SAFETY INSTRUCTIONS Length of Cord (Feet) AWG Size of Cord I. SAVE THESE INSTRUCTIONS - This manual 25 50 100 150 18 18 18 16 9. Do not operate charger with damaged cord or plug - replace them im- mediately.
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) 2. Do not attempt to use a step-up transformer, an engine generator or DC power 3. Do not allow anything to cover or clog the charger vents.
Installing or removing battery cartridge .Always switch off the tool before insertion or removal of the battery cartridge. .To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the tool.
Installing or removing drill bit or driver bit CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the bit.
Switch action Tool speed is increased by increasing pres- sure on the trigger. To start the tool, simply pull the trigger. Release the trigger to stop.
Operation 1) Hammer drilling operation : When drilling in concrete, granite, tile, etc., turn the knob so that the a mark on the knob points to the mark. Be sure to use a tungsten-carbide tipped bit. To position a hole accurately, start the tool slowly and then increase the speed gradually.
0 Drilling in wood When drilling in wood, best results are obtained with wood drills equipped with a guide screw, The guide screw makes drilling easier by pulling the bit into the workpiece. To prevent the bit from slipping when starting a hole, make an indentation with a center- punch and hammer at the point to be drilled.
Dust cover Use the dust cover to prevent dust and dirt from falling over the tool, yourself and on floor when performing overhead drilling operations. Install the dust cover on the tool’s collar as shown in the figures below. When installing it, push the dust cover firmly enough to be completely installed on the tool’s collar.
MAINTENANCE CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner.
Apr.-l4-'92 EN CORDLESS HAMMER DRILL Model 8411D Note: The switch and other part configurations may differ from country to country. 14.
Apr-l4--'92 EN MODEL 8411D ';iM DESCRIPTION 'LiM A& DESCRIPTION MACHINE ~ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 1 1 1 1 1 1 1 1 1 1 1 1 I 1 1 8 .
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.
An important point after buying a device Makita 8411D (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Makita 8411D yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Makita 8411D - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Makita 8411D you will learn all the available features of the product, as well as information on its operation. The information that you get Makita 8411D will certainly help you make a decision on the purchase.
If you already are a holder of Makita 8411D, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Makita 8411D.
However, one of the most important roles played by the user manual is to help in solving problems with Makita 8411D. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Makita 8411D along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
