Instruction/ maintenance manual of the product 6312DW Makita
Go to page of 16
Cordless Driver Drill Dimensions (L x W x H) Capacities No load speed IRPM) Steel Wood Wood screw Machine screw High Low Equipped with Electric Brake MODEL 6312D MODEL 6312DW With Fast Charger MODEL 6312DWG With Fast Charger Net weight INSTRUCTION MANUAL * Battery Cartridge 1201 I 1201A * Model DC1201 Fast Charger 13 mm I 24 mm I 6.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be sure switch is OFF when plugging in.
VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user - as well as damage to the tool.
IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY CARTRIDGE 1. SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for battery charger. 2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery.
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (SOOF) 2. Do not attempt to use a step-up transformer, an engine generator or DC power 3. Do not allow anything to cover or clog the charger vents.
Installing or removing battery cartridge *Always switch off the tool before insertion or removal or the battery cartridge. Battery cartridge *To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the tool.
0 If you charge a battery cartridge from a just-operated tool or a battery cartridge which has been left in a location exposed to direct sunlight or heat for a long time, the charg- ing light may flash in red color. If this occurs, wait for a while. Charging will begin after the battery cartridge cools.
Switch action Tool speed is increased by increasing pres- sure on the trigger. To start the tool, simply pull the trigger. Release the trigger to stop.
Adjusting fastening torque The fastening torque can be adjusted in six stages by turning the adjusting ring so that the pointer on the adjusting ring points to a number on the tool body. The fastening torque is minimum when the pointer points to the number 1 and maximum when it points to the a- marking.
Drilling operation First, turn the adjusting ring so that the pointer on the adjusting ring points to the st- marking. Then proceed as follows. *Drilling in wood When drilling in wood, best results are obtained with wood drills equipped with a guide screw.
MAINTENANCE CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner.
Sep.-08-'94 US CORDLESS DRIVER DRILL Model 63120 Note: The switch and other part configurations may differ from country to country. 14.
Sep.-08-'94 US MODEL 63120 ~ MACHINE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 16 19 20 21 22 23 24 25 26 27 28 29 30 31 32 'i:M $2D DESCRIPTION MACHINE 1 Name Plate 33 1 7 Tapping Screw BT4.
Recycling the Battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. @ N i-Cd To recycle the battery: 1. Remove the battery from the tool. 2. a). Take the battery to your nearest Makita Factory Service Center or b).
An important point after buying a device Makita 6312DW (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Makita 6312DW yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Makita 6312DW - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Makita 6312DW you will learn all the available features of the product, as well as information on its operation. The information that you get Makita 6312DW will certainly help you make a decision on the purchase.
If you already are a holder of Makita 6312DW, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Makita 6312DW.
However, one of the most important roles played by the user manual is to help in solving problems with Makita 6312DW. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Makita 6312DW along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
