Instruction/ maintenance manual of the product 6212DW Makita
Go to page of 16
Cordless Driver Drill Capacities Steel Wood Wood screw Machlne screw I I Equipped with Electric Brake MODEL 6212D MODEL 6212DW With Fast Charger MODEL 6212DWG With Fast Charger Dimensions Net No load .
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don’t carry tool with finger on switch. Be sure switch is OFF when plugging in.
VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet, etc.1 be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user - as well as damage to the tool.
IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY CARTRIDGE Length of Cord (Feet) AWG Size of Cord 1. 2. 3. 4. 5. 6. 7. 8. 9. IO. 11. 25 50 100 150 18 18 18 16 SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for battery charger.
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) or ABOVE 4OoC (104OF). 2. Do not attempt to use a step-up transformer, an engine generator or DC power 3. Do not allow anything to cover or clog the charger vents.
Installing or removing battery cartridge *Always switch off the tool before insertion or removal or the battery cartridge. *To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the tool.
0 If you charge a battery cartridge from a just-operated tool or a battery cartridge which has been left in a location exposed to direct sunlight or heat for a long time, the charg- ing light may flash in red color. If this occurs, wait for a while. Charging will begin after the battery cartridge cools.
__- a Switch action Tool speed is increased by increasing pres- sure on the trigger. To start the tool, simply pull the trigger. Release the trigger to stop. CAUTION : Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released.
Adjusting fastening torque When driving wood screws, predrill pilot Nominal diameter of wood screw Imm) 3.1 11 /E”) vent splitting of the workpiece. See the 3.5 19/64’,) chart. 3.8 15/32”) 4.5 111/64“) 4.8 13/16”) 5.1 113/64”) 5.5 17/32”) 5.
Drilling operation First, turn the adjusting ring so that the pointer on the adjusting ring points to the .I- marking. Then proceed as follows. Drilling in wood When drilling in wood, best results are obtained with wood drills equipped with a guide screw.
MAINTENANCE CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner.
Sep -08-'94 US CORDLESS DRIVER DRILL Model 6212D Note: The switch and other part configurations may differ from country to country. 14.
MACHINE MACHINE 1 1 Housing Set [With Item 591 33 1 2 1 Name Plate 34 1 3 1 Pan Head Screw M4x22 [With Washer1 35 1 4 7 Tapping Screw BT4x20 36 1 5 1 Hand Strap 37 1 38 1 6 1 Set Plate 39 1 7 1 Switch.
P Recycling the Battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. I Ni-Cd 1 To recycle the battery: 1. Remove the battery from the tool. 2. a). Take the battery to your nearest Makita Factory Service Center or b).
An important point after buying a device Makita 6212DW (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Makita 6212DW yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Makita 6212DW - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Makita 6212DW you will learn all the available features of the product, as well as information on its operation. The information that you get Makita 6212DW will certainly help you make a decision on the purchase.
If you already are a holder of Makita 6212DW, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Makita 6212DW.
However, one of the most important roles played by the user manual is to help in solving problems with Makita 6212DW. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Makita 6212DW along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
