Instruction/ maintenance manual of the product 6070DW Makita
Go to page of 16
Cordless Driver Drill No load speed Variable Speed, Reversible MODEL 6070D MODEL 6070DW With 3 Hour Charger weight I Net Dimensions (L x W x H) INSTRUCTION MANUAL SPECIFICATIONS - Model 6070D With Reversinq Switch & Battery 10 mm 4.5 mm x 20 mm 211 mmx49mmx192mm 1.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. 2.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don’t carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in.
IMPORTANT SAFETY INSTRUCTIONS I. SAVE THESE INSTRUCTIONS -This manual con- tains important safety and operating instructions for battery charger. 2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery.
ADDITIONAL SAFETY RULES FOR CHARGER AND TOOL 1. The Charger and the tool are specifically designed to work together. Do not attempt to charge any other cordless tool with this Charger. Do not attempt to charge the tool with any other charger. 2. Do not charge the tool when temperature is BELOW 10°C (50°F) or ABOVE 45°C (113°F).
Charging Uncap the charging connector hole. Connect the charging plug to the charging connector, then plug in the charger to the power receptacle. Charging takes 3 hours. CAUTION: 0 The battery in your new tool is not fully charged. You will need to charge it before use.
Installing or removing driver bit CAUTION : When installing or removing the bit, be careful not to touch the trigger switch. To install the bit, place it in the chuck as far as it will go. Tighten the chuck by hand. Place the chuck key in each of the three holes and tighten clockwise.
Reversing switch action This tool has a reversing switch to change the direction of rotation. Slide the reversing switch to the right for clockwise rotation or to the left for counterclockwise. Reversing switch - CAUTION: 0 Always check the direction of rotation before operation.
Bubble level This tool is equipped with a bubble level to aid in holding the tool horizontally. Simply center the bubble in the sight window. Screwdriving operation Place the point of the driver bit in the screw head and apply pressure to the tool. Start the tool slowly and then increase the speed grad- ually.
Storage of driver bit When not using the driver bit, return it to the storage cavity on the bottom of the tool. Drilling operation 0 Drilling in wood When drilling in wood, best results are obtained with wood drills equipped with a guide screw. The guide screw makes drilling easier by pulling the bit into the workpiece.
CAUTION: 0 Pressing excessively on the tool will not speed up the drilling. In fact, this excessive pressure will only serve to damage the tip of your bit, decrease the tool performance and shorten the service life of the tool. 0 There is a tremendous force exerted on the toolibit at the time of hole breakthrough.
MAINTENANCE CAUTION: Always be sure that the tool is switched off before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replace- ment parts.
ACCESSORIES CAUTION These accessories or attachments are recommended for use with your Makita tool specified in this manual The use of any other accessories or attachments might present a risk of inju.
14 A 10 mm (3/8) CORDLESS DRIVER DRILL Model 6070D Note The switch and other part configuratlons may differ from country to country.
MOL ITEM NO. - 1 2 3 4 5 6 7 8 9 10 11 Note 1 370D , DESCRIPTION ",'," & DESCRIPTION NE -E Drill Chuck S10 Pan Head Screw M5xl8 Gear Molor Holder 6 Switch Housing R Bubble Level Tap.
10 mm (3/8”) MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.
An important point after buying a device Makita 6070DW (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Makita 6070DW yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Makita 6070DW - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Makita 6070DW you will learn all the available features of the product, as well as information on its operation. The information that you get Makita 6070DW will certainly help you make a decision on the purchase.
If you already are a holder of Makita 6070DW, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Makita 6070DW.
However, one of the most important roles played by the user manual is to help in solving problems with Makita 6070DW. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Makita 6070DW along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
