Instruction/ maintenance manual of the product 5630DWA Makita
Go to page of 20
Cordless Circular Saw Blade Cutting depth No load speed Overall 45" iRPMi length 2,600 diameter 90" 165 mm 0 54" 0- 38" 364 mm (6- 1 /2") 10 ~ 2-1/8") 10 ~ 1-1/2") (.
GENERAL SAFETY RULES (For All Battery Operated Tools) WARNING! Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work Area Keep your work area clean and well lit.
Tool Use and Care Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. *Do not force tool. Use the correct tool for your application.
Specific Safety Rules 1. DANGER! Keep hands away from cutting area and blade. Keep your second hand on auxiliary handle, or motor housing. If both hands are holding the saw, they cannot be cut by the blade. Keep your body positioned to either side of the saw blade, but not in line with the saw blade.
11. Causes and Operator Prevention of Kickback: Kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing an uncontrolled saw to lift up and out of the workpiece toward the opera tor.
Do not use dull or damaged blade. Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and KICKBACK. Blade depth and bevel adjusting locking levers must be tight and secure before making cut. If blade adjustment shifts while cutting, it may cause binding and KICKBACK.
15. Place the wider portion of the saw base on that part of the workpiece which is solidly supported, not on the section that will fall off when the cut is made. As examples, Fig. 5 illustrates the RIGHT way to cut off the end of a board, and Fig. 6 the WRONG way.
SYMBOLS The followings show the symbols used for tool. ...... volts ................................. amperes ................................. herts ................................. kilograms hours ................................. minutes .........
IMPORTANT SAFETY INSTRUCTIONS Length of Cord (Feet) AWG Size of Cord FOR CHARGER & 25 50 100 150 18 18 18 16 BATTERY CARTRIDGE 1. SAVE THESE INSTRUCTIONS - This manual 9.
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (50OFI 2. Do not attempt to use a step-up transformer, an engine generator or DC power or ABOVE 4OoC (104OF). receptacle. 3.
Installing or removing battery cartridge *Always switch off the tool before insertion or removal of the battery cartridge. *To remove the battery cartridge, withdraw it from the tool while pressing the buttons on both sides of the cartridge.
*If you charge a battery cartridge from a just-operated tool or a battery cartridge which has been left in a location exposed to direct sunlight or heat for a long time, the charging light may flash in red color. If this occurs, wait for a while. Charging will begin after the battery cartridge cools.
Hex wrench storage When not in use, the conveniently stored. hex wrench can be CAUTIO N: Always be sure that the tool is switched off and the battery cartridge is removed before any adjustment is attempted. Adjusting depth of cut Loosen the lever on the depth guide and move the base up or down.
CAUTION: After adjusting the depth of cut and bevel cutting angle, be sure to tighten the screw. Sighting The front of the base is notched to provide two guide edges. For straight cuts, align the edge with 0" engraved on it with your cutting line on the workpiece.
Operation Hold the tool firmly. Set the base plate on the workpiece to be cut without the blade making any contact. Then turn the tool on and wait until the blade attains full speed. Now simply move the tool forward over the workpiece surface, keeping it flat and advancing smoothly until the sawing is completed.
MAINTENANCE CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes reg- ularly. Replace when they wear down to the limit mark.
Recycling the Battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. N i-Cd Tungsten carbide tipped saw blade Part No For wood To recycle the battery: 1. Remove the battery from the tool. 2.
Feb-04--'99 US CORDLESS CIRCULAR SAW Model 5630DW e- 59 Note: The switch and other part ConfigUratlOnS may differ from country to Country. 18.
MODEL 5630DW Feb-04-'99 US MACHINE ~ 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 21 28 29 30 I:"," GtD DESCRIPTION 16 21 31 41 51 61 71 81 91 1 1 2 2 2 1 1 1 1 3 2 1 1 1 1 1 1 1 .
I 1 MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy I Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.
An important point after buying a device Makita 5630DWA (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Makita 5630DWA yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Makita 5630DWA - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Makita 5630DWA you will learn all the available features of the product, as well as information on its operation. The information that you get Makita 5630DWA will certainly help you make a decision on the purchase.
If you already are a holder of Makita 5630DWA, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Makita 5630DWA.
However, one of the most important roles played by the user manual is to help in solving problems with Makita 5630DWA. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Makita 5630DWA along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
