Instruction/ maintenance manual of the product 5091DWG Makita
Go to page of 18
Cordless Circular Saw Blade diameter 85 mm (3-3/8") MODEL 5091DZ 85 mm (3-3/8") MODEL 5091DWH 85 mm (3-3/8") MODEL 5091DWG Without Battery or Charger 85 mm (3-3/8") MODEL 5091D Wit.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. 2.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be sure switch is OFF when plugging in.
IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY CARTRIDGE I. SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for battery charger. 2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery.
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) 2. Do not attempt to use a step-up transformer, an engine generator or DC power or ABOVE 4OoC (104OF). receptacle. 3.
ADDITIONAL SAFETY RULES 1. Be aware that this tool is always in an operating condition, because it does 2. Wear hearing protection. 3. Keep Guards In Place and In Working Order. not have to be plugged into an electrical outlet. Never wedge or tie lower guard open.
NEVER place your hand or fingers behind the saw. If kickback occurs, the saw could easily jump backwards over your hand, possibly causing severe injury. I Fig. 3 IO. Lower Guard. Raise lower guard with the retracting handle. 11. Adjustments. Before cutting be sure depth and bevel adjustments are tight.
15. Place the wider portion of the saw base on that part of the workpiece which is solidly supported, not on the section that will fall off when the cut is made. As examples, Fig. 5 illustrates the RIGHT way to cut off the end of a board, and Fig. 6 the WRONG way.
Installing or removing the battery cartridge 0 Always switch off the tool before insertion or removal of the battery cartridge. 0 To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the tool.
CAUTION: .The fast charger Model DC1201 is specifically designed to charge only Makita battery cartridges. Never use it for other purposes or for other manufacturer's batteries. When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it may not accept a full charge.
To install the blade, follow the removal procedure in reverse. BE SURE TO TIGHTEN THE BOLT SECURELY. Fig. 1 CAUTION : 0 Be sure the blade is installed with teeth pointing up at the front of the tool. 0 Use only the Makita hex wrench to install or remove the blade.
Adjusting the depth of cut Loosen the screw on the depth guide and move the base up or down. You can read the depth of cut by aligning the top of the notch in the depth guide with the graduations on its right side. (Note : This can be done for 0" bevel cutting only.
Sighting The front of the base is notched to provide two guide edges. For straight cuts, align the edge with 0' engraved on it with your cutting line on the workpiece. For 45' bevel cuts, align the edge with 45' engraved on it with your cutting line.
Guide rule The handy guide rule allows you to do extra-accurate straight cuts. Simply slide the guide rule up snugly against the side of the workpiece and secure it in position with the clamp screw on the front of the base. It also makes repeated cuts of uni- form width possible.
OPTIONAL ACCESSORIES The accessories listed in this manual are available at an extra cost from your Makita distributor or Makita factory service center. Service centers are listed on the warranty card packed with your tool. CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual.
Mar,-30-'95 US 85 mm (3-3/8") CORDLESS CIRCULAR SAW Model 5091D Note: The switch and other part configurations may differ from country to country.
MODEL 5091 D 'E :ED OESCRIPTION MA!aNE 26 27 26 29 30 31 32 33 341 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 Mar - 30 -'95 US '2 ED DESCRIPTION 1 1 3 1 1 1 1 1 1 1 1 1 1 1 3 1 1 1.
Recycling the Battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. I Ni-Cd I To recycle the battery: 1. Remove the battery from the tool. 2. a). Take the battery to your nearest Makita Factory Service Center or b).
An important point after buying a device Makita 5091DWG (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Makita 5091DWG yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Makita 5091DWG - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Makita 5091DWG you will learn all the available features of the product, as well as information on its operation. The information that you get Makita 5091DWG will certainly help you make a decision on the purchase.
If you already are a holder of Makita 5091DWG, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Makita 5091DWG.
However, one of the most important roles played by the user manual is to help in solving problems with Makita 5091DWG. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Makita 5091DWG along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
