Instruction/ maintenance manual of the product 4307D Makita
Go to page of 16
n 72v MODEL 43071) MODEL 4307DW With Fast Charger A C only DC 145 mm x 80 mm x 61 mm 0 7 kq 50Hz 60Hr 72v 15 3 4" x 3~1j8'' x 2 318") 11 5 It)bl 1 Hi INSTRUCTION MANUAL SPEC IF I CAT IONS Model 4307D 1 1 1 190 mm 14kg 19 16' ! (15 16") 11 2") 13'64 'I 17 15r32") 13 1 IbS! 12 mm 2.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in.
IMPORTANT SAFETY INSTRUCTIONS Length of Cord (Feet) 25 50 AWG Size of Cord 18 18 I. SAVE THESE INSTRUCTIONS - This manual 100 150 18 16 9. Do not operate charger with damaged cord or plug - replace them im- mediately.
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) 2. Do not attempt to use a step-up transformer, an engine generator or DC 3. Do not allow anything to cover or clog the charger vents.
Installing or removing battery cartridge 0 Always switch off the tool before insertion or removal of the battery cartridge. 0 To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the barrel.
Mounting blade First, use the hex wrench to remove the bolt which secures the blade clamp to the blade holder shaft. With the blade teeth facing forward, place the shank of the blade over the flat side of the blade holder shaft. Then place the blade clamp over the other side of the blade shank.
CAUTION : 0 Before inserting the battery cartridge into the tool, always check to see that the trigger 0 When not operating the tool, keep the lock-off lever in the SAFETY LOCK position.
Front flush cuts Loosen the bolt on the back of the base with the hex wrench, then slide the base backwards. Check the contact between the back edge of the blade and support roller, then secure the bolt. Bevel cutting 1. With the base tilted, you can make bevel cuts at any angle between 0" and 45' (left or right).
Finishing edges To trim edges or make dimensional adjust- ments, run the blade lightly along the cut edges. For smoother cutting of plywoods or other materials with easily splintered surfaces, the wood may be coated or transparent tape used over your cutting line.
Using circular guide 1. Use of the circular guide insures smooth cutting of circles (radius; 200 mm; 7-7/8") and arcs. clean, under 0 Knob Fit pin into this hole 2. When attaching the circular guide, use the pin, inserting it in the center hole (arrow) and secure it with the threaded knob.
Cutting performance The following reference table indicates the approximate cutting capacity from a single 1-hour battery charge. It may differ under some conditions. Material Thickness Cutting length Soft wood (,5,,6") 2.5 m (8.2 ft) Hard wood I ::,;: I 4 m (13ft) Mild steel I ;&:: 1 3 m (9.
MAINTENANCE CUATION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance and adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner.
Mar 03 '86 EN CORDLESS JIG SAW Model 4307D Note: The switch and other part configuratlons may differ from country to country. 15.
ITEM ,"&, DESCRIPTION MENE Hex Socket Head Bolt M4xB I 41 I 1 11 21 31 41 51 61 I1 91 IO 1 11 I 1 12 8 13 1 14 I I5 1 16 1 17 1 ni Lock Of1 Lever Mar 03 86 EN $:D DESCRIPTION 25 26 27 MACHINE.
An important point after buying a device Makita 4307D (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Makita 4307D yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Makita 4307D - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Makita 4307D you will learn all the available features of the product, as well as information on its operation. The information that you get Makita 4307D will certainly help you make a decision on the purchase.
If you already are a holder of Makita 4307D, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Makita 4307D.
However, one of the most important roles played by the user manual is to help in solving problems with Makita 4307D. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Makita 4307D along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
