Instruction/ maintenance manual of the product 3705 Makita
Go to page of 19
Trimmer 14' 1/4" MODEL 3705 23,000 215 mm (8 7/16") 1 8 kg (4 Ibs) INSTRUCTION MANUAL DOUBLE INSULATION SPEC IF I CAT IONS Overall length Net weight Collet chuck No load speed capacity .
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in.
ADDITIONAL SAFETY RULES 1. Wear hearing protection during extended periods of operation. 2. Handle the bits very carefully. 3. Check the bit carefully for cracks or damage before operation. Replace cracked or damaged bit immediately. 4. Avoid cutting nails.
Installing or removing trimmer bit CAUTION : Always be sure that the tool is switched off and unplugged before installing or removing the bit. Use the hex wrench to loosen the clamp bolt and lower the tool base. lnser the bit all the way into the collet cone and tighten the collet nut securely with the two wrenches.
Switch action To start the tool, move the switch lever to the “ON” position. To stop, move the switch lever to the “OFF” position. Operation *Set the tool base on the workpiece to be cut without the bit making any contact. Then turn the tool on and wait until the bit attains full speed.
Straight guide (Optional accessory) The straight guide is effectively used for straight cuts when chamfering or grooving. Install the straight guide on the guide holder with the wing bolt. Then use the hex wrench to loosen the bolts on the tool base and insert the guide holder into the grooves in the tool base.
Trimmer guide (Optional accessory) Trimming, curved cuts in veneers for fur- niture and the like can be done easily with the trimmer guide. The guide roller rides the curve and assures a fine cut. Install the trimmer guide on the guide holder with the wing bolt.
Templet guide The templet guide provides a sleeve through which the bit passes, allowing use of the trimmer with templet patterns. I To install the templet guide, loosen the screws on the tool base, insert the templet guide and then tighten the screws.
MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark.
ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner.
Bits STRAIGHT - Single Flute HIGH SPEED STEEL PART NO. A B C D E 733232-6A 118 5/16 1.118 1 /4 1-518 STRAIGHT - 2 Flute iDi- CARBIDE TIPPED PART NO. A B C D E 733003-2A 3/16 7116 1-318 114 2 HINGE MORTISING CARBIDE TIPPED I PARTNO. A B C D E 733006-9A 112 112 1-1116 114 1-1 311 6 VEINING - Single Flute SOLID CARBIDE PART NO.
ROUND NOSE CARBIDE TIPPED PART NO. A B C D E 733008-2A 1 14 15132 1~1 I4 114 1-718 733008-4A 318 9116 1-1 14 114 2 CORE BOX HIGH SPEED STEEL PART NO. A 8 C D E 733238-2A 1 I4 114 1-3116 1 I4 1-1 /2 VEE GROOVING -pr CARBIDE TIPPED I PARTNO A 8 C D E 01 733009-2A 318 112 1.
PANEL PILOT HIGH SPEED STEEL PART NO A B C D E 733236 OA 1 14 314 1 114 2 7116 CORNER ROUNDING HIGH SPEED STEEL Solid Pilof PARTNO A, AI B C D E R 733240 2A 11/16 3/16 112 1 114 1 314 114 COVE HIGH SPEED STEEL - Solid Pilot PARTNO.
7" BEVEL TRIMMER - Self-Piloting PART NO A B C D E 7331 28 2A 3116 114 11/16 114 19/16 2 FLUTE FLUSH TRIMMER CARBIDE TIPPED PART NO A B C D E 7331 28-9A 1 /2 112 1114 114 2-1/16 REPLACEMENT BEARI.
FLUTE FLUSH REPLACEMENT CUTTER SOLID CARBIDE PART NO. A B D 733129-6A 5/8 318 114 FOR FLUSH TRIMMER ASSEMBLY NO. 733129-2A I 114" REPLACEMENT ARBOR I PARTNO A B C D El I 733131-2A 518 318 1-114 1.
oct 09 87 us 114" TRIMMER Model 3705 Note The switch, noise suppressor and other part configurations may differ from country to country 17.
MODEL 3705 I;"," DESCRIPTION Mar 31 86 US ,,!& DESCRIPTION MACE 1 2 4 5 6 7 8 9 10 11 12 13 14 15 16 I7 18 19 11 22 23 24 25 1 1 1 2 1 1 1 1 1 1 1 1 2 1 1 1 2 2 1 3 1 2 1 - Clirrl Redr C.
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.
An important point after buying a device Makita 3705 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Makita 3705 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Makita 3705 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Makita 3705 you will learn all the available features of the product, as well as information on its operation. The information that you get Makita 3705 will certainly help you make a decision on the purchase.
If you already are a holder of Makita 3705, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Makita 3705.
However, one of the most important roles played by the user manual is to help in solving problems with Makita 3705. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Makita 3705 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
