Instruction/ maintenance manual of the product 3703 Makita
Go to page of 20
TLimmer Collet chuck capacity 114” 1/4” MODEL 3703 Overall length Net weight No load speed (RPMI 30,000 247 mm (9-23132”) 1.5 kg (3.3 lbsl INSTRUCTION MANUAL DOUBLE INSULATION.
IMPORTANT SAFETY IN STRU CTI 0 N S (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in.
ADDITIONAL SAFETY RULES 1. Wear hearing protection during extended periods of operation. 2. Handle the bits very carefully. 3. Check the bit carefully for cracks or damage before operation. 4. Avoid cutting nails. Inspect for and remove all nails from the workpiece before 5.
Installing or removing trimmer bit CAUTION : Always be sure that the tool is switched off and unplugged before installing or removing the bit. Insert the bit all the way into the collet cone and tighten the collet nur securely with the two wrenches. To remove the bit, follow the installation procedure in reverse.
Operation .Set the tool base on the workpiece to be cut without the bit making any contact. Then turn the tool on and wait until the bit attains full speed. Move the tool forward over the workpiece surface, keeping the tool base flush and advancing smoothly until the cutting is complete.
Straight guide (Optional accessory) The straight guide is effectively used for straight cuts when chamfering or grooving. Attach the guide plate to the straight guide with the bolt, the wave washer, the flat washer and the wing nut. Remove the chip deflector.
Circular work 0 Circular work may be accomplished if you assemble the straight guide and guide plate 0 Min. and max. radius of circles to be cut (distance between the center of circle and the as shown in the figure below. center of bit) are as follows : Min.
Trimmer guide Trimming, curved cuts in veneers for fur- niture and the like can be done easily with the trimmer guide. The guide roller rides the curve and assures a fine cut.
Templet guide The templet guide provides a sleeve through which the bit passes, allowing use of the trimmer with templet patterns. Remove the chip deflector. Loosen the screws and remove the base protector. Place the templet guide on the base and re- place the base protector.
MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes I regularly. Replace when they wear down to the limit mark.
ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner.
Bits STRAIGHT -Single Flute HIGH SPEED STEEL PART NO. A B C D E 7332328A 1 /8 5/16 1-1/8 1 /4 1-518 STRAIGHT - 2 Flute CARBIDE TIPPED PART NO. A B C D E 733003-2A 3/16 7/16 1 -3/8 114 2 733003-4A 114 3/4 1-3/16 114 2-1/8 733003-EA 5/16 1 1-1/8 114 2-3/16 HIGH SPEED STEEL (STRAIGHT - 2 Flute) PART NO.
ROUND NOSE -I+ CARBIDE TIPPED PART NO. A B C D E 733008-2A 1 I4 15/32 1-114 114 1-7lJ 7330084A 318 9/16 1-114 1 I4 2 CORE BOX 4DC HIGH SPEED STEEL PART NO. A B C D E 733238-2A 1 I4 114 1-3116 1 I4 1-112 VEE GROOVING CARBIDE TIPPED PART NO. A E C D E e 733009-2A 318 112 1-3/16 114 2 90" 14' DOVE TAIL 4DC CARBIDE TIPPED PART NO.
PANEL PILOT HIGH SPEED STEEL PART NO. A B C D E 733236-0A 1 /4 3/4 1 1 /4 2-7/16 CORNER ROUNDING CARBIDE TIPPED - Ball Bearing Pilot 733120-OA 718 1/2 3/8 1-1/4 1-15/16 3/16 733120-2A 112 1/2 1-1/4 1/4 1 /4 REPLACEMENT BEARING - NO 733132-4A HIGH SPEED STEEL - Solid Pilot PARTNO.
ROMAN OGEE -ID!? CARBIDE TIPPED - Ball Bearing Pilot B D PARTNO. A1 A1 C E R 2 5/32 733123-2A 1 3/8 15/32 1-1/4 1/4 REPLACEMENT BEARING - NO. 733132-2A FLUSH TRIMMER -Self Piloting CARBIDE TIPPED - Ball Bearing Pilot B D PARTNO. A1 A1 C E R 2 5/32 733123-2A 1 3/8 15/32 1-1/4 1/4 REPLACEMENT BEARING - NO.
COMBINATION FLUSH/22" BEVEL TRIMMER 2 CARBIDE TIPPED 733129-2A 518 318 1-1/4 1 /4 2-318 REPLACEMENT BEARING - NO. 733132-6A PART NO. A BI 82 C D E 733128-6A 7/16 1 /2 3/16 1-1/4 1/4 1-3/4 3 FLUTE.
3 FLUTE 22' BEVEL REPLACEMENT CUTTER L B pj I SOLID CARBIDE I PARTNO. A B D I 733129-8A 7/8 318 114 FOR BEVEL TRIMMER ASSEMBLY NO. 733129-4A ~~ ~~ 1/4" REPLACEMENT ARBOR I PARTNO. A B C D El I 733131-2A 518 318 1-1/4 1 I4 2-318 I FOR FLUSH TRIMMER ASSEMBLY NO.
Mar.-26-'90 US 114" TRIMMER 19.
MODEL 3703 Mar.-26-'90 US p.. ITEM AtD DESCRIPTION 'iiM GtD DESCRIPTION . MACHINE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 1 3 2 1 1 1 1 1 2 2 1 1 1 2 1 1 1 1 1 1 1 1 - Name .
An important point after buying a device Makita 3703 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Makita 3703 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Makita 3703 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Makita 3703 you will learn all the available features of the product, as well as information on its operation. The information that you get Makita 3703 will certainly help you make a decision on the purchase.
If you already are a holder of Makita 3703, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Makita 3703.
However, one of the most important roles played by the user manual is to help in solving problems with Makita 3703. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Makita 3703 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center