Instruction/ maintenance manual of the product MV1020 Magnadyne
Go to page of 20
Owner's Manual Mobile DVD/CD Player with 10.2" TFT Monitor Model: MV1020 / MV1020C For operational or technical assistance, after reading this manual, please call us toll free at (800) 638-3600 or visit www .
2 Safety Information . . . . . . . . . . . . . . . . . . . . 2-3 Disc and SD Card Notes . . . . . . . . . . . . . . . . . 4 Screen and DVD/CD Functions . . . . . . . . . . 5-7 Location of Functions . . . . . . . . . . . . . . . . . . 5 T urning the Unit On .
3 Features • This unit can play compatible discs recorded in either P AL or NTSC format. • CD, DVD, CD-R, CD-RW and MP3 Compatible. • SD Card Support. • Full-Function Wireless Remote Controller . • Multi-Language On-Screen Display Menu. • Built-In Dome Light System.
Disc Formats Supported by this Player: Discs which cannot be played with this player: • DVD-ROM • DVD-R/DVD-RAM • CDV • CD-G 4 Disc and SD Card Notes V I D E O (Single-sided disc only) 8 cm disc 8 cm disc Label side up Do not touch the underside of the disc Do not bend Wipe the disc from center toward the outside edge.
5 Screen and DVD/CD Functions 1. POWER Button: Press this button to turn the unit On/Off. 2. SOURCE Button: Press this button to change the play source between DVD/CD player and an auxiliary input source. 3. STOP Button: Stops play of picture or audio.
T urning the Unit On: Press the POWER on either the remote or the screen housing. Adjusting the Monitor: 1. Press the MODE button on the remote to activate the monitor adjustment menu. The following will be displayed on the screen: 2. Press the MODE button again to select the adjustment bar .
Screen and DVD/CD Functions 7 Dome Light Switch Infrared Remote Control Sensor: The Infrared remote control sensor receives the signals from the remote control.
8 1 9 10 6 18 19 11 13 22 23 24 14 15 17 5 2 3 4 16 20 21 8 12 7 25 POWER AUDIO ANGLE SUBTITLE DISPLA Y SETUP PLA Y/PAUSE PROG CLEAR PREV REV SLOW SD TITLE NEXT FWD A-B REPEA T SOURCE VOL– ZOOM PBC MENU SEARCH ENTER RETURN STOP EJECT VOL+ MOD E TFT FUN CTION UP MUTE DOWN 1 4 7 2 5 8 0 10+ 3 6 9 Remote Control Locations and Operation 1.
POWER AUDIO ANGLE SUBTITLE DISPLA Y SETUP PLA Y/PAUSE PROG CLEAR PREV REV SLOW SD TITLE NEXT FWD A-B REPEA T SOURCE VOL– ZOOM PBC MENU SEARCH ENTER RETURN STOP EJECT VOL+ MOD E TFT FUN CTION UP MUTE DOWN 1 4 7 2 5 8 0 10+ 3 6 9 30 29 26 27 28 31 32 Remote Control Locations and Operation 26.
Slow Play Each time the SLOW button is pressed during DVD play the speed is reduced as follows: 10 Basic Operation and Special Functions Display DVD Menu Screen 1. Press the MENU button to display the DVD menu screen. 2. Use the cursor button to select item.
11 Special Functions and Setup Menu DVD SPECIAL FUNCTIONS (Continued) Multi-Subtitle Language Function Press the SUBTITLE button during playback. Each time the button is pressed the subtitle language on the screen changes. Multi-Audio Language Function Press the AUDIO button during playback.
12 Setup Menu DISC SETTINGS Use the CURSOR buttons to make DISC setting selections. Press the ENTER button to confirm the setting. Audio Setting Use this screen to setup the audio language on multi-language discs. Subtitle Language Setting Use this screen to setup the subtitle language on multi-subtitle language discs.
Setup Menu VIDEO SETTINGS Use the CURSOR buttons to make VIDEO setting selections. Press the ENTER but- ton to confirm the setting. TV Aspect Setting Use this screen to setup the desired TV Aspect Ratio. AUDIO SETTINGS Use the CURSOR buttons to make AUDIO setting selections.
14 Setup Menu Last Play Function The Last Play function automatically book- marks the position on a DVD/CD disc and remembers the playback settings. Playback will resumes at the position which the player was turned off, the disc was ejected, or the power was cut off.
15 Installation When installing the MV1020 using a Custom Bracket Mounting System refer to the instructions included wi th with the bra cket. War ning: T ake e x tra ca re not to p enetrate the roof of your v ehicle during i nst allati on.
16 Wiring Diagram Black (Video Out) White (L-Audio Out) Red (R-Audio Out) Audio Video Output (Female RCA) Mini DIN Connector Black Wire - Ground Red Wire - Ignition Y ellow Wire - Batter y Blue Wire -.
17 Power Harness Wiring: The 4-wire harness provides battery and ignition 12 volts as well as a chassis ground. Route the power harness to the point in the vehicle that you will make the connections. Red Wire: The red wire in the harness should be connected to a +12 volt power wire that is turned on and of by the position of the ignition key .
18 Only qualified service personnel can remove the cover or service this player . Other wise the warranty will become invalid. No Power: • Check to see if the player is set to “On”. • Check to see that the power plug of the main unit is properly connected.
19 Replacement Parts Order Form Send Orders T o : Magnadyne Corporation We Accept Checks, Money Orders, Visa and Master Card A TTN: Consumer Parts Sales Make Checks Payable to: Magnadyne Corporation P . O. Box 5365 Carson, CA 90749-5365 SHIP TO: (No P .
Order By Mail Replacement Parts for MovieVision ® Systems DESCRIPTION MODEL # PRICE DVD Remote Control MV-1020RM $39.95 Ea. ONE (1) YEAR LIMITED WARRANTY Magnadyne Corporation or its authorized agent.
An important point after buying a device Magnadyne MV1020 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Magnadyne MV1020 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Magnadyne MV1020 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Magnadyne MV1020 you will learn all the available features of the product, as well as information on its operation. The information that you get Magnadyne MV1020 will certainly help you make a decision on the purchase.
If you already are a holder of Magnadyne MV1020, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Magnadyne MV1020.
However, one of the most important roles played by the user manual is to help in solving problems with Magnadyne MV1020. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Magnadyne MV1020 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
