Instruction/ maintenance manual of the product 5000 Little Wonder
Go to page of 21
© 2006 Mantis, Div . of Schiller -Pfeiffer Inc. All Rights Reserved. Owner s Manual and Saf ety Instr uctions Log Splitter Manual.
1 T able of Contents A. Introduction . . . . . . . . . . . . . . . . . . . . . . . .1 B. Log Splitter Specification . . . . . . . . . . . . .1 C. Unpacking and Assembly Instructions . .2 D . Service Information . . . . . . . . . . . . . . . . .5 E. Special Safety Information .
2 C. Unpacking and Assembly Instructions 1. Cut bands; remov e cover and tw o inserts supporting the top and the bottom of the unit. 2. Put log splitter with the cardboard part’ s box in the vertical position by holding the top of the beam and carefully lifting the top of the log splitter until it can stand.
3 4. Remov e and open box that is packaged between the log splitter cart and the vertical beam. 5. Remov e piv oting support from the box. Also remove wheels and hardware bag.
4 6. Folding Handle: Install the folding handle onto the frame using knobs (P/N 510501) and carriage bolts (P/N 510500). T o do this, align square opening of the folding handle with the frame’ s round hole and insert carriage bolt through. Secure it with the handle knob .
5 9. Pi voting Support Installation: Align mounting hole of the Pivoting Support (P/N 510103) with the frame hole, insert Bolt (P/N 510509) and secure with Lock Nut (P/N 510507). Repeat these steps to attach the other side of the Piv oting Support. 10.
6 W ARNING D ANGER READ AND UNDERST AND THE R ULES FOR SAFE OPERA TION AND ALL INSTRUCTIONS IN THIS MANU AL BEFORE OPERA TING THIS PRODUCT . BE F AMILIAR WITH THE CONTROLS AND THE PR OPER USE OF EQUIPMENT . IMPR OPER USE OR CARE OF THIS LOG SPLITTER, OR F AILURE TO WEAR PR OPER PRO TECTION, CAN RESUL T IN SERIOUS INJUR Y .
7 W ARNING WHEN USING THIS LOG SPLITTER, BASIC SAFETY PRECA UTIONS (INCLUDING THE FOLLO WING) SHOULD AL W A YS BE FOLLO WED T O REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND PERSONAL INJUR Y .
8 3. Important extension cord information • Make sure the extension cord is in good condition before use. • Based on the total length of cord that you are going to use, check the chart to make sure the cord meets the correct minimum cord gauge (A WG) requirements.
9 W ARNING NEVER CHECK HYDRA ULIC FLUID LEVEL WHILE MO T OR IS RUNNING OR WHILE THE T ANK IS STILL W ARM AFTER THE MO T OR IS SHUT OFF . HO T PRESSURIZED FLUID CAN ESCAPE THR OUGH THE OPENING AND CA USE SERIOUS INJUR Y .
10 W ARNING THE PRESSURE RELIEF V AL VE PRO TECTS THE HYDRA ULIC ASSEMBL Y WHEN THE LOG IS J AMMED FOR ABOUT 5 SECONDS. THE PRESSURE PLA TE SLO WL Y TRA VELS DO WN T O THE ORIGINAL POSITION AND CAN BE IMMEDIA TEL Y RE-A CTIV A TED . IF THE LOG DOES NO T SPLIT IMMEDIA TEL Y , DO NO T FORCE THE PRESSURE PLA TE OF THE LOG SPLITTER.
11 Overloading or ab using your log splitter can cause premature failure and can result in injury . Use common sense. • Always be sure to stand inside the Operator Zone when running your log splitter . G. Operation 1. Place the log splitter on firm, le veled ground and bloc k the w heels to prev ent them from rolling.
12 MAXIMUM LOG SIZE FOR THE SWIFT SPLIT IS 20” LONG X 12” DIA. 5. Place the log on the pressure plate of the machine. Be sure that the body of the log is lying firmly against the v ertical beam of the log splitter and the end of the log is well supported by the pressure plate.
13 IMPOR T ANT! DO NO T MIX FLUID BRANDS AND TYPES! DO NO T USE OTHER GRADE OILS. W ARNING BEFORE PERFORMING ANY MAINTENANCE BE SURE THA T : • LOG SPLITTER IS DISCONNECTED FR OM THE PO WER SOURCE. • PUSHER PLA TE IS FULL Y RETRA CTED (RETURNED TO THE LO WEST POSITION) AND NO RESIDU AL HYDRA ULIC ENERGY IS LEFT IN THE SYSTEM.
Drain Port 14 IMPOR T ANT! IF THE OIL LEVEL IS T OO HIGH THE HEA T WILL NO T BE DISSIP A TING Q UICKL Y ENOUGH AND THE TEMPERA TURE OF THE HYDRA ULIC SYSTEM WILL RISE.
15 K. T ransport • Log splitter is equipped with two 10” dia. wheels to mak e it easy to move around. • If you’ d like to move your log splitter to dif ferent locations, secure the unit during transport to pre vent damage or injury . Always tighten the bleed scre w to pre vent oil spill.
16 Maintain lo g splitter with car e • K eep the blade of the log splitter sharp and clean for better and safer performance • F ollow instructions for lubrication and oil change • K eep proper o.
17 M. T r oubleshooting N. Storage 1. Clean Unit. 2. Lubricate for rust prev ention 3. T ighten the Air Bleed Scre w 4. Fold in the handle (optional) 5.
18 O. Exploded V iew LOG SPLITTER EXPLODED VIEW 37 34 36 39 40 35 38 REV F, 12-20-05.
19 O. Parts List ITEM P AR T #. DESCRIPTION / REMARKS QTY 1 510100 CAR T BOTT OM WELDED ASSEMBL Y 1 2 510500 M10, CARRIA GE BOL T , SQ NECK, 60MM LG 2 3 510501 KNOB 2 4 510101 WHEEL 10 IN DIA 2 5 5101.
Specifications, descriptions, and illustrati ve material in this literature are as accurate as kno wn at the time of publication, but are subject to change without notice.
An important point after buying a device Little Wonder 5000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Little Wonder 5000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Little Wonder 5000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Little Wonder 5000 you will learn all the available features of the product, as well as information on its operation. The information that you get Little Wonder 5000 will certainly help you make a decision on the purchase.
If you already are a holder of Little Wonder 5000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Little Wonder 5000.
However, one of the most important roles played by the user manual is to help in solving problems with Little Wonder 5000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Little Wonder 5000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
