Instruction/ maintenance manual of the product PCI or AGP Card Apple
Go to page of 7
073-0672 R e v . A ð Xserve PCI or AGP Card Replacement Instructions F oll o w the inst r uctions in this sheet carefull y . F ailure to f oll o w these inst r uctions could damage y our equipment and v oid its w arrant y . Online inst r uctions c o v e r ing customer-installa b le pa r ts are a v aila b le at http://ww w .
Xserve PCI or AGP Cards - 2 4. If the ser v er is in the lock ed position (the y ello w security LED on the front panel is on), use the Allen ke y that came with the server to unloc k it. 5. If the cable management arm is not in use, unplug all e xternal cables e xcept the power cord.
Xserve PCI or AGP Cards - 3 9. Grasp the thumbscre ws and slide the bottom housing f orward part way to e xpose the two chassis le vers . (Figure 2) 10. While depressing both le v ers, pull the bottom housing all the wa y forw ard and remov e it from the rac k.
Xserve PCI or AGP Cards - 4 Removing a Card in the Dual-Slot Riser 1. Release the thumbscrew that secures the card f ence to the back of the server . 2. Disconnect the riser from the logic board and remov e the riser and card from the ser v er . (Figure 3) Figure 3 3.
Xserve PCI or AGP Cards - 5 Removing a Card in a Single-Slot Riser 1. Release the thumbscrew that secures the card f ence to the back of the server . (FIgure 5) Figure 5 2. Pull the clip on the riser forw ard to release the r iser from the logic board connector .
Xserve PCI or AGP Cards - 6 4. Disconnect the card from the riser . (Figure 7) Figure 7 Installing the Replacement Card 1. Install the replacement card in the riser card slot. 2. Reconnect the riser card to the logic board. 3. Tighten the thumbscrew that secures the card f ence to the back of the server .
Xserve PCI or AGP Cards - 7 ð Apple Computer , Inc. © 2002 Apple Computer , Inc. All rights reser ved. This document is protected under U .S. Cop yr ight Law and International T reaties, and no par t of this document may be reproduced in an y form without wr itten permission from Apple.
An important point after buying a device Apple PCI or AGP Card (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Apple PCI or AGP Card yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Apple PCI or AGP Card - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Apple PCI or AGP Card you will learn all the available features of the product, as well as information on its operation. The information that you get Apple PCI or AGP Card will certainly help you make a decision on the purchase.
If you already are a holder of Apple PCI or AGP Card, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Apple PCI or AGP Card.
However, one of the most important roles played by the user manual is to help in solving problems with Apple PCI or AGP Card. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Apple PCI or AGP Card along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
