Instruction/ maintenance manual of the product MKC (2015) Lincoln
Go to page of 363
.
.
I n f o r m a t i o n P r o v i d e d b y :.
Introduction About This Manual ............................................ 7 Symbols Glossary .............................................. 7 Data R ecording .................................................. 9 California Proposition 65 ............
Security Passive Anti-Theft System ............................ 80 Anti-Theft Alarm ............................................... 81 Steering Wheel Adjusting the Steering Wheel ..................... 82 Audio Control .................................
Storage Compartments Center Console .............................................. 157 Overhead Console ........................................ 157 Ticket Holders ................................................ 157 Starting and S topping the Engine General Information .
Essential T owing Checks ............................. 241 T ransporting the V ehicle ............................ 243 T owing the V ehicle on Four Wheels ........ 244 Driving Hints Breaking-In ..................................................... 246 Economical Driving .
Cleaning the Interior ................................... 302 Cleaning the Instrument Panel and Instrument Cluster Lens ......................... 303 Cleaning Leather Seats .............................. 304 R epairing Minor Paint Damage .............
6 MKC (TME), enUS A I n f o r m a t i o n P r o v i d e d b y :.
.
.
.
.
.
.
.
.
.
.
.
.
Instrument Panel Overview E173615 Air vents. See Hints on Controlling the Interior Climate (page 138). A Direction indicators. See Direction Indicators (page 94).
Instrument cluster . See Gauges (page 105). See Warning Lamps and Indicators (page 107). C Wiper lever . See Wipers and Washers (page 86). D Information and entertainment display . E Audio unit. F Hazard warning flasher switch. See Hazard W arning Flashers (page 250).
R ear Exterior Overview E173614 See Changing a Bulb (page 293). A See Changing the Wiper Blades (page 291). B 21 MKC (TME), enUS A At a Glance I n f o r m a t i o n P r o v i d e d b y :.
See Changing a Bulb (page 293). C Liftgate. See Manual Liftgate (page 73). See Power Liftgate (page 74). D See Changing a R oad Wheel (page 328). E Tire pressures.
GENERAL INFORMATION See the following sections for directions on how to properly use safety restraints for children. W ARNINGS Always make sure your child is secured properly in a device that is appropriate for their height, age and weight. Child safety restraints must be bought separately from your vehicle.
R ecommendations for Safety Restraints for Children Recommended restraint type Child size, height, weight, or age Child Use a child safety seat (sometimes called an infant carrier , convertible seat, or toddler seat). Children weighing 40 lb (18 kg) or less (generally age four or younger).
• Y ou are required by law to properly use safety seats for infants and toddlers in the United States and Canada. • Many states and provinces require that small children use approved booster seats until they reach age eight, a height of 4 feet 9 inches (1.
When installing a child safety seat with combination lap and shoulder belts: • Use the correct safety belt buckle for that seating position. • Insert the belt tongue into the proper buckle until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle.
4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage. Make sure the tongue is latched securely by pulling on it. E142875 5.
10 . Before placing the child in the seat, forcibly move the seat forward and back to make sure the seat is securely held in place. T o check this, grab the seat at the belt path and attempt to move it side to side and forward and back. There should be no more than 1 inch (2.
E144054 The LATCH anchors are located at the rear section of the rear seat between the cushion and seat back below the symbols as shown. Follow the child seat manufacturer' s instructions to properly install a child seat with LATCH attachments. Follow the instructions on attaching child safety seats with tether straps.
Using T ether Straps Many forward-facing child safety seats include a tether strap which extends from the back of the child safety seat and hooks to an anchoring point called the top tether anchor . T ether straps are available as an accessory for many older safety seats.
E142539 3. Clip the tether strap to the anchor as shown. 4. Tighten the child safety seat tether strap according to the manufacturer' s instructions. If your child restraint system is equipped with a tether strap, and the child restraint manufacturer recommends its use, Ford also recommends its use.
Always use booster seats in conjunction with your vehicle lap and shoulder belt. T ypes of Booster Seats E68924 • Backless booster seats If your backless booster seat has a removable shield, remove the shield.
E142596 E142597 33 MKC (TME), enUS A Child S afety I n f o r m a t i o n P r o v i d e d b y :.
If the booster seat slides on the vehicle seat upon which it is being used, placing a rubberized mesh sold as shelf or carpet liner under the booster seat may improve this condition. Do not introduce any item thicker than this under the booster seat. Check with the booster seat manufacturer' s instructions.
R ecommendations for attaching child safety restraints for children Use any attachment method as indicated below by X Combined weight of child and child seat Restraint T ype Safety belt only Safety be.
E1 12197 The childproof locks are located on the rear edge of each rear door and must be set separately for each door . Left-Hand Side T urn counterclockwise to lock and clockwise to unlock. Right-Hand Side T urn clockwise to lock and counterclockwise to unlock.
PRINCIPLE OF OPERATION W ARNINGS Always drive and ride with your seatback upright and the lap belt snug and low across the hips. T o reduce the risk of injury , make sure children sit where they can be properly restrained. Never let a passenger hold a child on his or her lap while your vehicle is moving.
• retractor and anchor pretensioner at the front outboard seating positions • belt tension sensor at the front outboard passenger seating position • safety belt warning light and chime • crash sensors and monitoring system with readiness indicator .
Using Safety Belts During Pregnancy W ARNING Always ride and drive with your seatback upright and the safety belt properly fastened. The lap portion of the safety belt should fit snug and be positioned low across the hips. The shoulder portion of the safety belt should be positioned across the chest.
Automatic Locking Mode In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt.
1. Grasp the safety belt webbing at the top of the seatback. 2. Pull the safety belt webbing forward, firmly . 3. After pulling the safety belt forward, allow the safety belt to feed back into the safety belt retractor as much as possible. If necessary , press the seatback down to allow the safety belt webbing to retract further .
SAFETY BEL T W ARNING LAMP AND INDICAT OR CHIME This lamp illuminates and an audible warning will sound if the driver' s safety belt has not been fastened when the vehicle' s ignition is turned on. Conditions of operation Then... If ... The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds.
SAFETY BEL T MINDER Belt-Minder ™ This feature supplements the safety belt warning function by providing additional reminders by intermittently sounding a chime and illuminating the safety belt warning light when the driver seat or front passenger seat is occupied and the safety belt is unbuckled.
Deactivating and Activating the Belt-Minder Feature W ARNING While the system allows you to deactivate it, this system is designed to improve your chances of being safely belted and surviving an accident. W e recommend you leave the system activated for yourself and others who may use the vehicle.
Ford Motor Company recommends that all safety belt assemblies in use in vehicles involved in a crash be replaced. However , if the crash was minor and an authorized dealer finds that the belts do not show damage and continue to operate properly , they do not need to be replaced.
The Personal Safety System provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of airbag-related injuries.
PRINCIPLE OF OPERATION W ARNINGS Airbags do not inflate slowly or gently , and the risk of injury from a deploying airbag is the greatest close to the trim covering the airbag module. All occupants of your vehicle, including the driver , should always properly wear their safety belts, even when an airbag supplemental restraint system is provided.
While the system is designed to help reduce serious injuries, contact with a deploying airbag may also cause abrasions or swelling. T emporary hearing loss is also a possibility as a result of the noise associated with a deploying airbag.
Proper Driver and Front Passenger Seating Adjustment W ARNING National Highway T raffic Safety Administration (NHTSA) recommends a minimum distance of at least 10 inches (25 centimeters) between an occupant ’ s chest and the driver airbag module.
W ARNINGS Any alteration or modification to the front passenger seat may affect the performance of the front passenger sensing system which could seriously increase the risk of injury or death.
If a person of adult size is sitting in the front passenger seat, but the airbag off indicator lamp is lit, it is possible that the person isn ’ t sitting properly in the seat. If this happens: • T urn the vehicle off and ask the person to place the seat back in the full upright position.
on the floor . Sitting improperly can increase the chance of injury in a crash event. For example, if an occupant slouches, lies down, turns sideways, sits forward, leans forward or sideways, or puts one or both feet up, the chance of injury during a crash is greatly increased.
E152533 The system consists of the following: • A label or embossed side panel indicating that side airbags are fitted to your vehicle. • Side airbags located inside the driver and front passenger seatbacks. • Front passenger sensing system. ·Crash sensors and monitoring system with readiness indicator .
W ARNINGS T o reduce risk of injury , do not obstruct or place objects in the deployment path of the curtain airbag. If the curtain airbags have deployed, the curtain airbags will not function again. The curtain airbags (including the A, B and C pillar trim and headliner) must be inspected and serviced by an authorized dealer .
CRASH SENSORS AND AIRBAG INDICAT OR W ARNING Modifying or adding equipment to the front end of your vehicle (including frame, bumper , front end body structure and tow hooks) may affect the performance of the airbag system, increasing the risk of injury .
The fact that the safety belt pretensioners or airbags did not activate for both front seat occupants in a crash does not mean that something is wrong with the system. Rather , it means the restraints control module determined the accident conditions (for example, crash severity , belt usage) were not appropriate to activate these safety devices.
GENERAL INFORMATION ON RADIO FREQUENCIES This device complies with Part 15 of the FCC Rules and with Industry Canada license-ex empt RSS standard(s). Operation is subject to the following two conditio.
REMO TE CONTROL Intelligent Access K ey E144506 Y our intelligent access keys to operate the power locks and the remote start system. The key must be in your vehicle to activate the push-button start system. R emovable Key Blade The intelligent access key also contains a removable mechanical key blade that you can use to unlock the driver door .
E176225 1. Slide the release on the back of the remote control and pivot the cover off . E153890 2. Insert a coin into the slot and twist to separate the housing. E176226 3. R emove the batteries. 4. Install new batteries with the + facing each other .
V ehicles with automatic climate control can be configured to operate when the vehicle is remote started. See Automatic Climate Control (page 136). A manual climate control system will run at the setting it was set to when you switched the vehicle off .
Y ou may have to be closer to the vehicle than when starting due to ground reflection and the added noise of the running vehicle. Y ou can disable or enable the remote start system through the information display .
PRINCIPLE OF OPERATION MyK ey allows you to program keys with restricted driving modes to promote good driving habits. All but one of the keys programmed to the vehicle can be activated with these restricted modes. Any keys that have not been programmed are referred to as administrator keys or admin keys.
• Audio system maximum volume of 45%. A message will be shown in the display when you attempt to ex ceed the limited volume. Also, the speed-sensitive or compensated automatic volume control will be disabled.
T o clear all MyKeys of all MyK ey settings, press the left arrow button to access the main menu and scroll to: Action and Description Message Press the OK button. Settings Press the OK button. MyK ey Press and hold the OK button until the following message displays.
CHECKING MYKEY SY STEM ST ATUS Y ou can find information on programmed MyK ey(s) using the information display control on the steering wheel. See Information Displays (page 112). T o find information on a programed MyKey(s), press the left arrow button to access the main menu and scroll to: Description Message Press the OK button.
USING MYKEY WITH REMO TE ST ART SY STEMS MyK ey is not compatible with non Ford-approved, aftermarket remote start systems. If you choose to install a remote start system, see an authorized dealer for a Ford-approved remote start system.
Potential Causes Condition Purchase a new key from your authorized dealer . I lost the only admin key . Program a spare key . See Passive Anti-Theft S ystem (page 80). I lost a key · The vehicle has a remote start system that is recognized as an admin key .
L OCKING AND UNLOCKING Y ou can use the power door lock or the remote control to lock and unlock your vehicle. Power Door L ocks The power door lock is on the driver and front passenger door panels. E138628 Unlock A Lock B Door Lock Indicator An LED on each door window trim lights when you lock the door .
Intelligent access at the driver door will unlock all doors when you disable two-stage unlocking. Locking the Doors E176108 Press the button to lock all the doors. The direction indicators will flash. Press the button again within three seconds to confirm that all the doors are closed.
E180643 Left-Hand Side T urn clockwise to lock. Right-Hand Side T urn counterclockwise to lock. Opening a R ear Door from Inside Pull the interior door handle twice to unlock and open a rear door . The first pull unlocks the door and the second pull will unlatch the door .
Smart Unlocks This feature helps to prevent you from unintentionally locking your intelligent access key inside the passenger compartment or rear cargo area.
Illuminated Entry The interior lamps and select exterior lamps will light when you unlock the doors with the remote control. The system turns off the lights if: • Y ou start your vehicle. • Y ou press the remote control lock button. • They are on for 25 seconds.
MANU AL LIFTGATE W ARNINGS It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a crash, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts.
Press the button to unlatch the liftgate. Once unlatched, pull on the outside handle to open the liftgate. With the R emote Control E138630 Press the button twice within three seconds. Pull on the outside handle to open. Closing the Liftgate E155976 A handle is located inside the liftgate to help with closing.
If the liftgate falls after the liftgate has stopped in the open position, you may hear four short warning tones. This indicates ex cessive weight on the gate or a possible gas strut failure. Have an authorized dealer check the system if you still have the issue after you remove the load.
Note: Splashing water may cause the hands-free liftgate to open. K eep the intelligent access transmitter away from the rear bumper detection area while washing your car . From Outside the V ehicle Opening 1. Unlock the liftgate with the remote control or power door unlock control.
Obstacle Detection When Closing The system stops when it detects an obstacle and three short tones sound. Once you remove the obstacle, you can power close the liftgate. Note: Entering your vehicle while the liftgate is closing can cause your vehicle to bounce and activate obstacle detection.
T o program additional personal entry codes, repeat Steps 1-3, then for S tep 4: • Press 3·4 to save personal code 2. • Press 5·6 to save personal code 3. • Press 7·8 to save personal code 4. • Press 9·0 to save personal code 5. Tips: • Do not set a code that uses five of the same number .
Displaying the Factory-Set Code Note: Y ou will need to have two programmed intelligent access keys for this procedure. T o display the factory-set code in the information display: E170454 1. Open the center console lid. 2. Place the first programmed key in the backup slot.
P ASSIVE ANTI-THEFT SYS TEM Note: The system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection.
ANTI-THEFT ALARM (If Equipped) The system will warn you of an unauthorized entry to your vehicle. It will be triggered if any door , the luggage compartment or the hood is opened without using the key , remote control or keyless entry keypad.
ADJUS TING THE STEERING WHEEL W ARNING Do not adjust the steering wheel when your vehicle is moving. Note: Make sure that you are sitting in the correct position. See Sitting in the Correct Position (page 141). 1 2 2 E95178 1. Unlock the steering column.
Memory Feature Y ou can save and recall the steering column position with the memory function. See Memory Function (page 145). Pressing the adjustment control during memory recall cancels the operation.
Press and hold the seek button to: • tune the radio to the next station up or down the frequency band • seek through a track. VOICE CONTROL (If Equipped) E145980 V oice recognition A End a call B Answer a call C See MyLincoln T ouch ™ (page 350).
Use this control to access some of the MyLincoln T ouch features in the information display . Navigate through the screen and press OK to select. See MyLincoln T ouch ™ (page 350). HEATED STEERING WHEEL (If Equipped) See MyLincoln T ouch ™ (page 350).
WINDSHIELD WIPERS Note: Fully defrost the windshield before switching on the windshield wipers. Note: Make sure you switch off the wipers before entering a car wash. Note: Clean the windshield and wiper blades if they begin to leave streaks or smears.
AUT OWIPERS (If Equipped) Note: Fully defrost the windshield before switching on the windshield wipers. Note: Make sure you switch off the windshield wipers before entering a car wash. Note: Clean the windshield and wiper blades if they begin to leave streaks or smears.
Note: When you set the wiper system to intermittent wipe and the autowiper system is on, the autowiper sensitivity setting adjusts the wiper speed according to the moisture on the windshield only . Use the wiper lever to wipe the windshield on-demand.
Press the top of the button at the end of the lever to switch on the intermittent wiper . Press the button again to switch on low-speed wipe. Press the bottom of the button to switch the wiper off , or to change the wiper speed from low-speed to intermittent.
LIGHTING CONTROL E142449 Off A Parking lamps, instrument panel lamps, license plate lamps and tail lamps B Headlamps C High Beams E162679 Push the lever forward to switch the high beams on. Push the lever forward again or pull the lever toward you to switch the high beams off .
AUT OLAMPS (If Equipped) W ARNING The daytime running lamps system does not activate the tail lamps and may not provide adequate lighting during low visibility driving conditions. Also, the autolamps switch position may not activate the headlamps in all low visibility conditions, such as daytime fog.
INSTRUMENT LIGHTING DIMMER Note: If you disconnect the battery or it becomes discharged, the illuminated components will switch to the maximum setting. A B E165366 Press repeatedly or press and hold to dim. A Press repeatedly or press and hold to brighten.
T ype 2 - Configurable Note: If this type is equipped, you are able to switch the daytime running lamps on or off using the information display controls.
The high beams will switch off if: • the system detects the headlamps of an approaching vehicle or the tail lamps of a preceding vehicle. • vehicle speed falls below 16 mph (25 km/h) • the ambie.
Note: T ap the lever up or down to make the direction indicators flash three times to indicate a lane change. WEL COME LIGHTING The Lincoln welcome mat projection lights are on the bottom of the exterior mirror housings. They will project an image onto the ground a short distance from your vehicle when welcome lighting or lighted entry turns on.
R ear Interior Lamp (If Equipped) A E170429 The rear interior lamps are located in the headliner by the grab handles. • Y ou can switch individual rear lamps on independently by pressing the switch (A). AMBIENT LIGHTING (If Equipped) The ambient lighting system is adjusted with the MyLincoln T ouch.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Action Cause Clean the grille surface in front of the radar or remove the object causing the obstruction. The surface of the radar in the grille is dirty or obstructed in some way . W ait a short time. It may take several minutes for the radar to detect that it is free from obstruction.
E71340 The cruise control indicator light replaces the adaptive cruise control indicator light if you select normal cruise control. The gap setting does not display , the system does not automatically respond to lead vehicles and automatic braking is not active.
DRIVER ALERT (If Equipped) W ARNING The driver alert system is designed to aid you. It is not intended to replace your attention and judgment. Y ou are still responsible to drive with due care and attention. Note: The system will store the on or off setting in the information display menu through ignition cycles.
The current assessment of your alertness is within a typical range. E131359 The current assessment of your alertness indicates that you should rest as soon as safely possible. The status bar will travel from left to right as the calculated alertness level decreases.
Note: If a MyK ey® is detected, pressing the button will not affect the on or off status of the system. Y ou can only change the mode and intensity settings. E144813 Press the button located on the left steering wheel stalk to switch the system on or off .
Intensity: This setting affects the intensity of the steering wheel vibration used for the alert and alert + aid modes. This setting is not valid for the aid mode. • Low • Medium • High System Display E151660 When you turn the system on, an overhead graphic of a vehicle with lane markings will display in the information display .
• Using the turn signal indicator . • Evasive steering maneuver . T roubleshooting Why is the feature not available (line markings are gray) when I can see the lane markings on the road? V ehicle .
Why is the feature not available (line markings are gray) when I can see the lane markings on the road? Faint lane markings (partial yellow lane markings on concrete roads) Lane width too narrow or to.
BLIND SPO T INFORMATION SY STEM Blind Spot Information System (BLIS®) with Cross T raffic Alert (If Equipped) W ARNING T o help avoid injuries, NEVER use the Blind Spot Information System as a replacement for using the interior and exterior mirrors or looking over your shoulder before changing lanes.
E142440 In this first example, the left sensor is only partially obstructed; zone coverage is nearly maximized. 219 MKC (TME), enUS A Driving Aids I n f o r m a t i o n P r o v i d e d b y :.
E142441 Zone coverage also decreases when parking at shallow angles. Here, the left sensor is mostly obstructed; zone coverage on that side is severely limited.
System Lights and Messages E142442 The Blind Spot Information and Cross T raffic Alert systems illuminate a yellow alert indicator in the outside mirror on the side of your vehicle the approaching vehicle is coming from. Note: The alert indicator dims when the system detects nighttime darkness.
When you remove a blockage, you can reset the system two ways: • While driving, the system detects at least two objects. • Y ou cycle the ignition from on to off and then back on. If the blockage is still present after the key cycle and driving in traffic, check again for a blockage.
False Alerts Note: If your vehicle has a factory equipped tow bar and it is towing a trailer , the sensors will detect the trailer and turn the Blind Spot Information and Cross T raffic Alert systems off to avoid false alerts. For non-factory equipped tow bars, you may want to turn the Blind Spot Information System off manually .
If your vehicle loses electrical power while you are driving (or if the ignition is turned off ), you can steer the vehicle manually , but it takes more effort. Extreme continuous steering may increase the effort it takes for you to steer . This occurs to prevent internal overheating and permanent damage to your steering system.
E156131 When your vehicle rapidly approaches another vehicle, a red warning light flashes and a tone sounds. The brake support system assists you in reducing any collision speed by pre-charging the brakes. If the risk of collision continues to increases after the audio-visual warning, the brake support prepares the brake system for rapid braking.
Action Cause Clean the radar sensor cover or remove the obstruction The radar sensor cover in the grille is dirty or obstructed W ait a short time. The radar may take several minutes to reset after yo.
DRIVE CONTROL LINCOLN DRIVE CONTROL Lincoln Drive Control delivers the Lincoln driving experience through a suite of sophisticated electronic vehicle systems. These systems continuously monitor your driving inputs and the road conditions to optimize ride comfort, steering, handling, powertrain response and sound.
T o change your vehicle ’ s Drive Control settings from the main menu on the information display: 1. Choose Settings. 2. Choose V ehicle. 3. Choose Drive Control. 4. Select the shift position you would like to configure, either D or S . 5. Choose from Comfort, Normal, or Sport modes as your preferred setting in D.
REAR UNDER FL OOR STORAGE Cargo Management System (If Equipped) E142445 The system is located in the floor of the cargo area. Lift the handle to open. L UGGAGE CO VERS W ARNINGS Make sure that the posts are properly latched in mounting features. The cover may cause injury in a sudden stop or accident if it is not securely installed.
Note: Never place loads directly on the roof panel. The intended design of the roof panel is not to directly carry a load. Make sure that you securely fasten the load.
Payload - is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the Tire Label on the B-Pillar or the edge of the driver door (vehicles exported outside the US and Canada may not have a Tire Label).
E142517 E143817 CARGO 232 MKC (TME), enUS A L oad Carrying I n f o r m a t i o n P r o v i d e d b y :.
Cargo W eight - includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. GAW (Gross Axle W eight) - is the total weight placed on each axle (front and rear) including vehicle curb weight and all payload.
GVWR (Gross V ehicle W eight R ating) - is the maximum allowable weight of the fully loaded vehicle (including all options, equipment, passengers and cargo).
E142524 W ARNING Ex ceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury .
E143819 GCW GVW GCW (Gross Combined W eight) - is the Gross V ehicle W eight plus the weight of the fully loaded trailer . GCWR (Gross Combined W eight Rating) - is the maximum allowable weight of the vehicle and the loaded trailer , including all cargo and passengers, that the vehicle can handle without risking damage.
W ARNINGS Do not ex ceed the GVWR or the GAWR specified on the Safety Compliance Certification Label. Do not use replacement tires with lower load carrying capacities than the original tires because they may lower the vehicle ’ s GVWR and GAWR limitations.
*Suppose your vehicle has a 1400-pound (635-kilogram) cargo and luggage capacity . Y ou and one of your friends decide to pick up cement from the local home improvement store to finish that patio you have been planning for the past two years.
T OWING A TRAILER W ARNINGS Do not ex ceed the GVWR or the GAWR specified on the certification label. T owing trailers beyond the maximum recommended gross trailer weight ex ceeds the limit of the vehicle and could result in engine damage, transmission damage, structural damage, loss of vehicle control, vehicle rollover and personal injury .
Note: This feature does not prevent trailer sway , but reduces it once it begins. Note: This feature cannot stop all trailers from swaying. Note: In some cases, if vehicle speed is too high, the system may activate multiple times, gradually reducing vehicle speed.
ESSENTIAL T OWING CHECKS Follow these guidelines for safe towing: • Do not tow a trailer until you drive your vehicle at least 1000 miles (1600 kilometers). • Consult your local motor vehicle laws for towing a trailer . • See the instructions included with towing accessories for the proper installation and adjustment specifications.
T railer Lamps W ARNING Never connect any trailer lamp wiring to the vehicle' s tail lamp wiring; this may damage the electrical system resulting in fire. Contact your authorized dealer as soon as possible for assistance in proper trailer tow wiring installation.
Note: R econnect the wiring to the trailer after removing the trailer from the water . When backing down a ramp during boat launching or retrieval: • Do not allow the static water level to rise above the bottom edge of the rear bumper .
Front-wheel drive vehicles must have the front wheels placed on a tow dolly when towing your vehicle from the rear using wheel lift equipment. This prevents damage to the transmission. T owing an all-wheel drive vehicle requires that all wheels be off the ground, such as using a wheel lift and dollies or flatbed equipment.
Follow these guidelines if you have a need for recreational (RV) towing. An example of recreational towing would be towing your vehicle behind a motorhome. W e designed these guidelines to prevent damage to your transmission. Front-wheel drive vehicles CANNO T be flat-towed (all wheels on the ground) as vehicle or transmission damage may occur .
BREAKING-IN Y ou need to break in new tires for appro ximately 300 miles (480 kilometers). During this time, your vehicle may exhibit some unusual driving characteristics. Avoid driving too fast during the first 1000 miles (1600 kilometers). V ary your speed frequently and change up through the gears early .
• Driving on flat terrain offers improved fuel economy as compared to driving on hilly terrain. • T ransmissions give their best fuel economy when operated in the top cruise gear and with steady pressure on the gas pedal. • Four-wheel-drive operation (if equipped) is less fuel efficient than two-wheel-drive operation.
W ARNINGS Always correctly install the floor mats to the retention posts so that they cannot slip out of position or obstruct pedal operation. Do not place unsecured floor mats or any other covering in the foot well. Do not place additional floor mats or any other covering on top of the original floor mats.
RO ADSIDE ASSIST ANCE V ehicles Sold In the United States: Getting R oadside Assistance T o fully assist, if you have a vehicle concern, Ford Motor Company offers a complimentary R oadside Assistance program. This program is separate from the New V ehicle Limited W arranty .
V ehicles Sold In Canada: Getting R oadside Assistance Canadian clients who require roadside assistance, call 1-800-387-9333. V ehicles Sold In Canada: Using R oadside Assistance Canadian R oadside coverage and benefits may differ from the United States coverage.
Note: When you try to restart your vehicle after a fuel shutoff , the vehicle makes sure that various systems are safe to restart. Once your vehicle determines that the systems are safe, then the vehicle will allow you to restart. Note: In the event that your vehicle does not restart after your third attempt, contact an authorized dealer .
4 2 1 3 E142664 1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery . 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery . 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery .
4 1 3 2 E142665 1. R emove the jumper cable from the ground metal surface or connecting point, if available. 2. R emove the jumper cable on the negative (-) terminal of the booster vehicle' s battery . 3. R emove the jumper cable from the positive (+) terminal of the booster vehicle' s battery .
GETTING THE SERVICES Y OU NEED W arranty repairs to your vehicle must be performed by an authorized dealer . While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction.
Additional Assistance If you have questions or concerns, or are unsatisfied with the service you are receiving, follow these steps: 1. Contact your Sales R epresentative or Service Advisor at your selling/servicing authorized dealer .
2. Four or more repair attempts are made on the same nonconformity (a defect or condition that substantially impairs the use, value or safety of the vehicle) OR 3. The vehicle is out of service for repair of nonconformities for a total of more than 30 calendar days (not necessarily all at one time).
to resolve them. A Customer Claim Form will be mailed that will need to be completed, signed and returned to the BBB along with proof of ownership. Upon receipt, the BBB will review the claim for eligibility under the Program Summary Guidelines.
If you cannot find unleaded fuel or can only get fuel with an anti-knock index lower than is recommended for your vehicle, contact our Customer R elationship Center . The use of leaded fuel in your vehicle without proper conversion may damage the effectiveness of your emission control system and may cause engine knocking or serious engine damage.
FORD MOT OR COMP ANY Customer R elationship Center 1555 Fairlane Drive Fairlane Business Park #3 Allen Park, Michigan 48101 U .S.A. T elephone: +971 4 3326084 T oll-Free Number of the Kingdom of Saudi Arabia: 800 8971409 Local T elephone Number of Kuwait: 24810575 F AX: +971 4 3327299 Email: menacac@ford.
If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company .
FUSE SPECIFICATION CHART Pre-Fuse Bo x The pre-fuse bo x is in the engine compartment attached to the positive battery post. This bo x contains several high current fuses. If you need to replace one of these high current fuses, see an authorized dealer .
E157389 262 MKC (TME), enUS A F uses I n f o r m a t i o n P r o v i d e d b y :.
Protected components Fuse amp rating Fuse Anti-lock brake system module 50A 2 F7 Anti-lock brake system module 30A 2 F8 Fuel pump relay 20A 2 F9 Blower motor relay 40A 2 F10 Run start relay 30A 2 F11 .
Protected components Fuse amp rating Fuse Cooling fan 1 (with trailer tow) 50A 2 Cooling fan 2 (without trailer tow) 40A 2 F18 Cooling fan 2 (with trailer tow) 50A 2 Anti-lock brake system module run/.
Protected components Fuse amp rating Fuse Alternator sensor 10A 1 F28 Rain sensor 15A 1 F29 R ear wiper W asher pump relay coil Left-hand headlamp 20A 1 F30 Right-hand headlamp 20A 1 F31 V ehicle powe.
Protected components Fuse amp rating Fuse Not used — F38 Powertrain control ignition start power - run 5A 1 F39 Electronic power assist steering run/start 10A 1 F40 Not used — F41 Adaptive cruise .
Protected components Fuse amp rating Fuse Not used — F47 Not used — F48 1 Mini fuse 2 J-case fuse Circuits switched Relay Run start R1 Horn R2 Fuel pump R3 R ear window washer pump R4 Cooling fan .
Circuits switched Relay Cooling fan relay 4 (with trailer tow) R10 Air conditioning clutch R11 Cooling fan relay 1 (with trailer tow) R12 Cooling fan relay 3 (without trailer tow) Cooling fan relay 2 .
E145984 269 MKC (TME), enUS A F uses I n f o r m a t i o n P r o v i d e d b y :.
Protected components Fuse amp rating Fuse Lighting (ambient, glove bo x, vanity , dome, cargo) 10A 1 1 Memory seats 7 .5A 1 2 Driver door unlock 20A 1 3 Not used (spare) 5A 1 4 Subwoofer amplifier 20A.
Protected components Fuse amp rating Fuse Climate control 7 .5A 2 12 Gear shift control Push-button ignition Cluster 7 .5A 2 13 Datalink module logic Steering column module logic Not used (spare) 10A .
Protected components Fuse amp rating Fuse Occupant classification sensor 5A 2 22 Delayed accessory (driver window switch, moonroof logic, power inverter logic) 10A 1 23 Central lock and unlock 30A 1 2.
Protected components Fuse amp rating Fuse V oice control Radio and active noise control 20A 1 33 Run/start bus (fuse #19 , 20 , 21, 22, 35, 36, 37 , circuit breaker) 30A 1 34 R estraints control modul.
R ear Cargo Fuse Box The fuse panel is located in the cargo area on the passenger side. Open the fuse panel cover to gain access to the fuses. E175700 274 MKC (TME), enUS A F uses I n f o r m a t i o .
Protected components Fuse amp rating Fuse Not used — F1 Not used — F2 Hands-free liftgate module 5A 1 F3 Spare Not used — F4 Not used — F5 Not used — F6 R ear heated seats 30A 2 F7 Power cin.
Protected components Fuse amp rating Fuse Not used — F13 Power seats 30A 2 F14 Auxiliary power point - inside of floor console 20A 2 F15 Auxiliary power point - rear of floor console 20A 2 F16 Not u.
CHANGING A FUSE Fuses W ARNING Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. E142430 If electrical components in the vehicle are not working, a fuse may have blown.
GENERAL INFORMATION Have your vehicle serviced regularly to help maintain its roadworthiness and resale value. There is a large network of Ford authorized dealers that are there to help you with their professional servicing expertise.
OPENING AND CL OSING THE HOOD Opening the Hood E142457 1. Inside your vehicle, pull the hood release handle located under the left-hand side of the instrument panel. E142458 2. Go to the front of your vehicle and release the auxiliary latch. 3. Lift the hood until the lift cylinders hold it open.
UNDER HOOD OVER VIEW - 2.0L ECOBOOST ™ A B C D E F G H E171684 Engine coolant reservoir A Engine oil dipstick B 280 MKC (TME), enUS A M aintenance I n f o r m a t i o n P r o v i d e d b y :.
Engine oil filler cap C Brake fluid reservoir D Battery E Power distribution bo x F Air filter assembly G Windshield washer fluid reservoir H 281 MKC (TME), enUS A M aintenance I n f o r m a t i o n P.
UNDER HOOD OVER VIEW - 2.3L ECOBOOST ™ A B C D E F G H E171685 Engine coolant reservoir A Engine oil dipstick B 282 MKC (TME), enUS A M aintenance I n f o r m a t i o n P r o v i d e d b y :.
Engine oil filler cap C Brake fluid reservoir D Battery E Power distribution bo x F Air filter assembly G Windshield washer fluid reservoir H ENGINE OIL DIPSTICK E170468 A B MIN A MAX B ENGINE OIL CHECK 1. Make sure that your vehicle is on level ground.
Adding Engine Oil E142732 Only use oils certified for gasoline engines by the American Petroleum Institute (API). An oil with this trademark symbol conforms to the current engine and emission system protection standards and fuel economy requirements of the International Lubricants Specification Advisory Council (ILSAC), comprised of U .
Note: For best results, coolant concentration should be tested with a refractometer such as R otunda tool 300-ROB75240 available from your authorized dealer . Ford does not recommend the use of hydrometers or coolant test strips for measuring coolant concentrations.
• Do not use alcohol, methanol, brine or any engine coolants mix ed with alcohol or methanol antifreeze (coolant). Alcohol and other liquids can cause engine damage from overheating or freezing. • Do not add extra inhibitors or additives to the coolant.
If the engine reaches a preset over-temperature condition, the engine will automatically switch to alternating cylinder operation. Each disabled cylinder acts as an air pump and cools the engine. When this occurs the vehicle will still operate. However: • The engine power will be limited.
Have an authorized dealer check and change the transmission fluid and filter at the correct service interval. See Scheduled Maintenance (page 451). Y our transmission does not consume fluid. However , the fluid level should be checked if the transmission is not working properly , (i.
W ARNINGS When lifting a plastic-cased battery , ex cessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and damage to the vehicle or battery . Lift the battery with a battery carrier or with your hands on opposite corners.
Some other computer settings, like the clock and radio station presets, are also maintained in memory by power from the low voltage battery . When a technician disconnects and connects the low voltage battery , these settings are erased.
CHECKING THE WIPER BLADES E142463 Run the tip of your fingers over the edge of the blade to check for roughness. Clean the wiper blades with washer fluid or water applied with a soft sponge or cloth. CHANGING THE WIPER BLADES The wiper arms can be manually moved when the ignition is off .
Poor wiper quality can be improved by cleaning the wiper blades and the windshield. ADJUS TING THE HEADLAMPS V ertical Aim Adjustment The assembly plant properly aims the headlamps on your vehicle. If your vehicle has been in an accident, have the alignment of your headlamps checked by your authorized dealer .
E171 165 5. Locate the vertical adjuster on each headlamp. T urn the adjuster either clockwise or counterclockwise in order to aim the headlamp. 6. Close the hood and switch off the lamps. Horizontal Aim Adjustment Horizontal aim is not required for this vehicle and is non-adjustable.
Examples of unacceptable moisture (usually caused by a lamp water leak) are: • W ater puddle inside the lamp. • Large water droplets, drip marks or streaks present on the interior of the lens. T ake your vehicle to a dealer for service if any of the above conditions of unacceptable moisture are present.
R eplacing License Plate Lamp Bulb 3 2 1 E72789 1. Carefully release the spring clip. 2. R emove the lamp. 3. R emove the bulb. R everse steps to reinstall bulb. R eplacing High-Mount Brake Lamp Bulb Y our vehicle is equipped with an LED center high-mount stop lamp located in the spoiler , designed to last the life of the vehicle.
T rade number Function LED * T ail/brake lamp LED * T urn lamp - rear LED * Backup lamp W5W License plate lamp LED * High-mount brake lamp LED * Interior lamps * T o replace these lamps, see your authorized dealer . T o replace instrument panel lights, see your authorized dealer .
CHANGING THE ENGINE AIR FIL TER W ARNING T o reduce the risk of vehicle damage and personal burn injuries, do not start your engine with the air cleaner removed. Do not remove the air cleaner while the engine is running. When changing the air filter element, use only the air filter element listed in the Motorcraft Parts table.
4. Install the new air filter element. Slide the open end of the air filter element in first, below the tab. Then push the closed end of the air filter into the bottom of the tray .
GENERAL INFORMATION Y our Ford or Lincoln authorized dealer has many quality products available to clean your vehicle and protect its finishes. CLEANING PRODUCTS For best results, use the following pr.
Stripes or Graphics (if equipped) Do not use a commercial or high-pressure sprayer on the surface or edge of stripes and graphics. This can cause damage to the film and cause the edge of the film to peel away from the vehicle surface.
• Do not allow wax to come in contact with any non-body (low-gloss black) colored trim. The wax will discolor or stain the parts over time. • R oof racks. • Bumpers. • Grained door handles. • Side moldings. • Mirror housings. • Windshield cowl area.
CLEANING THE INTERIOR W ARNINGS Do not use cleaning solvents, bleach or dye on the vehicle ’ s safety belts, as these actions may weaken the belt webbing. On vehicles equipped with seat-mounted airbags, do not use chemical solvents or strong detergents.
Cleaning Procedure Type of S tain Use lukewarm water and rinse by dabbing with clean water . Fruit juice , jam, jelly , syrup or ketchup. Use cold water and rinse by dabbing with clean water . Avoid warm water because it makes these substances coagulate.
• W ash or wipe your hands clean if you have been in contact with certain products such as insect repellent and suntan lotion to avoid possible damage to the interior painted surfaces. • Do not allow air fresheners and hand sanitizers to spill onto interior surfaces.
REP AIRING MINOR P AINT D AMAGE Authorized dealers have touch-up paint to match your vehicle ’ s color . Y our vehicle color code is printed on a sticker on the front, left-hand side door jamb. T ake your color code to your authorized dealer to make sure you get the correct color .
General • Store all vehicles in a dry , ventilated place. • Protect from sunlight, if possible. • If vehicles are stored outside, they require regular maintenance to protect against rust and damage.
Miscellaneous • Make sure all linkages, cables, levers and pins under your vehicle are covered with grease to prevent rust. • Move vehicles at least 25 feet (8 meters) every 15 days to lubricate working parts and prevent corrosion.
GENERAL INFORMATION Notice to utility vehicle and truck owners W ARNINGS Utility vehicles have a significantly higher rollover rate than other types of vehicles.
How your vehicle differs from other vehicles Sport utility vehicles and trucks can differ from some other vehicles in a few noticeable ways. Y our vehicle may be: E145299 • Higher - to allow higher load carrying capacity and to allow it to travel over rough terrain without getting hung up or damaging underbody components.
As a result of the above dimensional differences, Sport utility vehicles and trucks often will have a higher center of gravity and a greater difference in center of gravity between the loaded and unloaded condition. These differences that make your vehicle so versatile also make it handle differently than an ordinary passenger car .
The traction grades, from highest to lowest are AA, A, B, and C. The grades represent the tire ’ s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.
* R ecommended inflation pressure: The cold inflation pressure found on the Safety Compliance Certification Label (affix ed to either the door hinge pillar , door-latch post, or the door edge that meets the door-latch post, next to the driver' s seating position), or Tire Label located on the B-Pillar or the edge of the driver door .
A. P: Indicates a tire, designated by the Tire and Rim Association, that may be used for service on cars, sport utility vehicles, minivans and light trucks. Note: If your tire size does not begin with a letter this may mean it is designated by either the European Tire and Rim T echnical Organization or the Japan Tire Manufacturing Association.
Speed rating - mph (km/ h) Letter rating 168 mph (270 km/h) W 186 mph (299 km/h) Y Note: For tires with a maximum speed capability over 149 mph (240 km/h), tire manufacturers sometimes use the letters ZR. For those with a maximum speed capability over 186 mph (299 km/h), tire manufacturers always use the letters ZR.
* T raction: The traction grades, from highest to lowest are AA, A, B, and C. The grades represent the tire' s ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance.
C. Maximum Load Dual lb (kg) at psi (kPa) cold: Indicates the maximum load and tire pressure when the tire is used as a dual, defined as four tires on the rear axle (a total of six or more tires on the vehicle).
Location of the Tire Label Y ou will find a Tire Label containing tire inflation pressure by tire size and other important information located on the B-Pillar or the edge of the driver door . Inflating Y our Tires Safe operation of your vehicle requires that your tires are properly inflated.
that meets the door-latch post, next to the driver' s seating position), or Tire Label which is located on the B-Pillar or the edge of the driver ’ s door . The cold inflation pressure should never be set lower than the recommended pressure on the Safety Compliance Certification Label or Tire L abel.
7 . Check the sidewalls to make sure there are no gouges, cuts or bulges. Inspecting Y our Tires and Wheel V alve Stems Periodically inspect the tire treads for uneven or ex cessive wear and remove objects such as stones, nails or glass that may be wedged in the tread grooves.
Age W ARNING Tires degrade over time depending on many factors such as weather , storage conditions, and conditions of use (load, speed, inflation pressure) the tires experience throughout their lives. In general, tires should be replaced after six years regardless of tread wear .
W ARNINGS of loss of vehicle control, vehicle rollover , personal injury and death. Additionally the use of non-recommended tires and wheels could cause steering, suspension, axle, transfer case or power transfer unit failure. If you have questions regarding tire replacement, contact your authorized dealer as soon as possible.
Safety Practices W ARNINGS If your vehicle is stuck in snow , mud, or sand, do not rapidly spin the tires. Spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. Do not spin the wheels at over 35 mph (56 km/h).
Tire R otation Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation. Note: Y our vehicle may be equipped with a dissimilar spare wheel and tire assembly .
• If possible, avoid fully loading your vehicle • Purchase chains or cables from a manufacturer that clearly labels body to tire dimension restrictions. • Use 10 mm cables or chains only on front axle with 235/50R18 tires. • Not all S-class snow chains or cables meet these restrictions.
Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver ’ s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale.
Understanding Y our Tire Pressure Monitoring System The tire pressure monitoring system measures pressure in your four road tires and sends the tire pressure readings to your vehicle. The low tire pressure warning light will turn on if the tire pressure is significantly low .
Customer action required Possible cause Low tire pressure warning light Make sure tires are at the proper pressure. See Inflating your tires in this chapter .
When Inflating Y our Tires When putting air into your tires (such as at a gas station or in your garage), the tire pressure monitoring system may not respond immediately to the air added to your tires.
Dissimilar Spare Wheel and Tire Assembly Information W ARNING Failure to follow these guidelines could result in an increased risk of loss of vehicle control, injury or death. If you have a dissimilar spare wheel and tire, then it is intended for temporary use only .
• W et weather driving capability . • All-wheel driving capability When driving with the full-size dissimilar spare wheel and tire assembly additional caution should be given to: • T owing a trailer . • Driving vehicles equipped with a camper body .
E142551 6. Block the diagonally opposite wheel. 7 . Loosen each wheel lug nut one-half turn counterclockwise, but do not remove them until the wheel is raised off the ground. Note: Jack at the specified locations to avoid damage to the vehicle. 8. The vehicle jacking points are shown here, and are depicted on the yellow warning label on the jack.
13. Remove the jack and fully tighten the lug nuts in the order shown. See T echnical Specifications (page 334). Stowing the flat tire 1. Put the jack and lug wrench away . Make sure the jack is fastened so it does not rattle when you drive. 2. Unblock the wheels.
E143746 333 MKC (TME), enUS A Wheels and Tires I n f o r m a t i o n P r o v i d e d b y :.
TECHNICAL SPECIFICATIONS Wheel Lug Nut T orque Specifications W ARNING When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum or brake disc that contacts the wheel.
E145950 Wheel pilot bore A Inspect the wheel pilot bore and mounting surface prior to installation. R emove any visible corrosion or loose particles. 335 MKC (TME), enUS A Wheels and Tires I n f o r m.
ENGINE SPECIFICATIONS 2.3L EcoBoost engine 2.0L EcoBoost engine Engine 138 122 Cubic inches Minimum 87 octane Minimum 87 octane R equired fuel 9 .5:1 9.3:1 Compression ratio 0 . 027-0 . 031 in. (0 . 70-0 .80 mm) 0 . 027-0 . 031 in. (0 . 70-0 .80 mm) Spark plug gap Drivebelt R outing 2.
A. The long drivebelt is on the first pulley groove closest to the engine B. The short drivebelt is on the second pulley groove farthest from the engine 2.
2.3L EcoBoost engine 2.0L EcoBoost engine Component CYFS-12Y -2 / SP -537 CYFS-12Y -2 / SP -537 Spark plugs 3 FP70 Cabin air filter WW -2250 (driver side) Windshield wiper blade WW -1575 (passenger side) WW -1106 (rear window) 1 Failure to use the correct air filter element may result in severe engine damage.
VEHICLE IDENTIFICATION NUMBER The vehicle identification number is located on the left-hand side of the instrument panel. E142476 Please note that in the graphic, XXXX is representative of your vehicle identification number .
TRANSMISSION CODE DESIGNATION E167814 The transmission code is on the Safety Compliance Certification Label. The following table shows the transmission code along with the transmission description.
TECHNICAL SPECIFICATIONS Ford part number / Ford specification Ford part name or equivalent Capacity Item PM-20 / WSS-M6C65-A2 Motorcraft High Performance DO T 4 L V Motor V ehicle Brake Fluid Between.
Ford part number / Ford specification Ford part name or equivalent Capacity Item Engine oil 5,6, 7 2.3L EcoBoost VC-3DIL-B (U .S.); CVC-3DIL-B (Canada) / WSS-M97B44-D2 Motorcraft Orange Antifreeze / Coolant Prediluted 9 . 7 qt (9 .2 L) Engine coolant 8 2.
Ford part number / Ford specification Ford part name or equivalent Capacity Item CYN-16-R (Canada) / WSH-M17B19-A YN-12-D / WSH-M1C231-B Motorcraft P AG Refrigerant Compressor Oil 4.
1 Ford recommends using Motorcraft (Ford) DOT 4 L V High Performance Brake Fluid or equivalent meeting WSS-M6C65-A2. Use of any fluid other than the recommended fluid may cause degraded brake performance and not meet the Ford performance standards. K eep brake fluid clean and dry .
GENERAL INFORMATION Radio Frequencies and R eception Factors AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and T elecommunications Commission (CRT C). Those frequencies are: • AM: 530 , 540-1700 , 1710 kHz • FM: 87 .
Do not expose discs to direct sunlight or heat sources for extended periods. MP3 and WMA T rack and Folder Structure Audio systems capable of recognizing and playing MP3 and WMA individual tracks and .
Note: The MyLincoln T ouch system controls most of the audio features. See Entertainment (page 376). A B C D E F E171512 347 MKC (TME), enUS A Audio System I n f o r m a t i o n P r o v i d e d b y :.
CD slot: Insert a CD. A Eject: Press the control to eject a CD. B TUNE: T urn the control to search manually through the radio frequency band. The system stops at the first station it finds in that direction. In SIRIUS mode, the system selects the previous or next channel.
E170492 A C B Auxiliary input jack (Line in) A USB ports B SD card slot C See Entertainment (page 376). 349 MKC (TME), enUS A Audio System I n f o r m a t i o n P r o v i d e d b y :.
GENERAL INFORMATION W ARNING Driving while distracted can result in loss of vehicle control, crash and injury . W e strongly recommend that you use extreme caution when using any device that may take your focus off the road. Y our primary responsibility is the safe operation of your vehicle.
A B G C D F E E161891 Phone A Navigation (or Information if your vehicle is not equipped with Navigation) B Climate C Settings D Home E Information F Entertainment G 351 MKC (TME), enUS A M yLincoln T.
This system uses a four-corner strategy to provide quick access to several vehicle features and settings. The touchscreen provides easy interaction with your cellular phone, multimedia, climate control and navigation system. The corners display any active modes within those menus, such as phone status or the climate temperature.
Press to select any of the following: • Services • T ravel Link • Alerts • Calendar • Apps ENTERT AINMENT Press to select any of the following: • AM • FM • SIRIUS • CD • USB • BT.
Using Y our Steering Wheel Controls Depending on your vehicle and option package, use these controls on your steering wheel: • VOL: Control the volume of playing media. • SEEK/PHONE : Seek presets or use as you normally would in other entertainment modes.
• Do not leave playing devices in your vehicle during extreme conditions as it could cause them damage. See your device' s user guide for further information. • For your safety , some SYNC functions are speed-dependent. Their use is limited to when your vehicle is traveling at speeds under 3 mph (5 km/h).
Restricted features Enabling V alet Mode Editing settings while the rear view camera or active park assist are active Editing wireless settings Wi-Fi and Wireless Editing the list of wireless networks.
Privacy Information When you connect a cellular phone to SYNC, the system creates a profile within your vehicle that links to that cellular phone. This profile helps in offering you more cellular features and operating more efficiently .
Accessing and Adjusting Modes through Y our V ehicle Information Display E156609 358 MKC (TME), enUS A M yLincoln T ouch ™ I n f o r m a t i o n P r o v i d e d b y :.
The display is located on the center of your instrument cluster . It allows you to view and make minor adjustments to active modes without taking your hands off the wheel. For example: • In entertainment mode, you can view what is now playing, change the audio source, select presets and make some adjustments.
These commands can be said at any time during a voice session "Cancel" "Exit" "Go back" "List of commands" "Main menu" "Next page" "Pre.
An important point after buying a device Lincoln MKC (2015) (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Lincoln MKC (2015) yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Lincoln MKC (2015) - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Lincoln MKC (2015) you will learn all the available features of the product, as well as information on its operation. The information that you get Lincoln MKC (2015) will certainly help you make a decision on the purchase.
If you already are a holder of Lincoln MKC (2015), but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Lincoln MKC (2015).
However, one of the most important roles played by the user manual is to help in solving problems with Lincoln MKC (2015). Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Lincoln MKC (2015) along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
