Instruction/ maintenance manual of the product LS (2006) Lincoln
Go to page of 320
Introduction 4 Instrument Cluster 10 W arning and control lights 10 Gauges 14 Entertainment Systems 16 AM/FM stereo with in-dash six CD 16 AM/FM stereo cassette with CD 20 Navigation system 25 Climate.
Seating and Safety Restraints 154 Seating 154 Safety restraints 162 Airbags 174 Child restraints 185 Tires, Wheels and Loading 197 T ire Information 197 V ehicle loading 211 T railer towing 216 Recrea.
Maintenance and Specifications 275 Engine compartment 277 Engine oil 279 Battery 282 Engine Coolant 284 Fuel information 290 Air filter(s) 301 Part numbers 304 Refill capacities 304 Lubricant specifications 306 Accessories 312 Index 314 All rights reserved.
CALIFORNIA Proposition 65 W arning W ARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
SAFETY AND ENVIRONMENT PROTECTION W arning symbols in this guide How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed.
SPECIAL NOTICES New V ehicle Limited W arranty For a detailed description of what is covered and what is not covered by your vehicle’ s New V ehicle Limited W arranty , refer to the Warranty Guide that is provided to you along with your Owner’ s Guide.
T o access this information, special equipment must be directly connected to the recording modules. Ford Motor Company and Ford of Canada do not access event data recorder information without obtainin.
These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Child Seat Installation.
V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant .
W ARNING LIGHTS AND CHIMES W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’ s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works.
Check fuel cap (if equipped): Illuminates when the fuel cap may not be properly installed. Continued driving with this light on may cause the Check engine warning light to come on. Refer to Fuel filler cap in the Maintenance and Specifications chapter .
Safety belt: Reminds you to fasten your safety belt. A chime will also sound to remind you to fasten your safety belt. Charging system: Illuminates when the battery is not charging properly . Engine oil pressure: Illuminates when the oil pressure falls below the normal range, refer to Engine oil in the Maintenance and Specifications chapter .
Steering column lock (if equipped): Illuminates when the steering column is locked. If the light stays on the vehicle will not start, make sure the key is the correct key , refer to Securilock 娂 in the Locks and Security chapter .
Key-in-ignition warning chime: Sounds when the key is left in the ignition in the OFF/LOCK or ACCESSORY position and the driver’ s door is opened. Headlamps on warning chime: Sounds when the headlamps or parking lamps are on, the ignition is off (the key is not in the ignition) and the driver’ s door is opened.
Odometer: Registers the total miles (kilometers) of the vehicle. • Standard instrument cluster • Optional instrument cluster T rip odometer: Registers the miles (kilometers) of individual journeys. T o reset, depress the RESET control. T o switch the display from T rip A to the T rip B, depress the A/B control.
AUDIO SYSTEMS Audiophile Satellite Ready AM/FM Stereo In-Dash Six CD Radio (if equipped) 1. Seek: Press and release SEEK / for previous/next strong station or track. 2. Rewind: In CD mode, press until desired selection is reached. Fast forward: In CD mode, press until desired selection is reached.
the music. Press SEL to engage/disengage. T urn the volume control to increase/decrease the level of ambiance. Occupancy: Press DSP again to change the occupancy mode to optimize sound for ALL SEA TS, DRIVER SEA T or REAR SEA TS. Press SEL to scroll through settings.
RDS on/off (Radio Data System) : Allows traffic, program type and station information from RDS-equipped FM stations. T raffic: In FM mode with RDS ON, this feature allows you to hear traffic broadcasts. W ith the feature ON, press SEEK or SCAN to find a station broadcasting a traffic report (if it is broadcasting RDS data).
preset stations for AM/FM1/FM2 . Press and momentarily hold AM/FM. AUTOSET will flash on the display . When the six strongest stations are filled, the station stored in preset 1 will begin playing. If there are less than six strong stations, the system will store the last one in the remaining presets.
CA T : CA T is only available when equipped with Satellite Radio. Y our Audiophile radio comes equipped with Satellite ready capability . The kit to enable Satellite reception is available through your Lincoln dealer . Detailed Satellite instructions are included with the dealer installed kit.
T reble: Allows you to increase or decrease the audio system’ s treble output. Press TREB then press SEL to decrease or increase the treble levels. 4. Balance: Allows you to shift speaker sound between the right and left speakers. Press BAL then press SEL to shift sound to the left or right .
9. Mute: Press to mute the playing media. RDS: (Radio Data System): Allows you to access FM stations which are RDS- equipped. Press RDS then SEL to select from: T raffic — Allows you to receive traffic announcements and control their volume level. T raffic information is not available in most U.
14. AM/FM/CD: Press AM/FM to select a radio frequency . Press while in tape or CD mode to return to radio mode. Press CD to enter CD mode and to play a CD already in the system. CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only .
GENERAL AUDIO INFORMATION Radio frequencies: AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and T elecommunications Commission (CRTC). Those frequencies are: AM - 530, 540–1700, 1710 kHz FM- 87.
Don’t: • Expose discs to direct sunlight or heat sources for extended periods of time. • Clean using a circular motion. CD units are designed to play commercially pressed 4.
1. VOL-PUSH : Press to turn the system ON/OFF . T urn to adjust the audio volume level. 2. AUDIO : Press to enter audio mode and access radio, CD, CDDJ, DVD (if equipped) settings. 3. MAP : Press to enter map mode and view your current vehicle position on the map.
Initial map display After pressing AGREE to the initial W ARNING screen, you will move into the initial map screen which shows the current vehicle location. Pressing the globe icon will take you to the user settings — audible feedback, navigation units, language and clock (if equipped).
T o play a previously loaded CD: 1. Ensure that the vehicle ignition is on. 2. Press AUDIO. 3. Press CD to select a CD which is already loaded. (NO CD will appear in the display if there are no CDs loaded into the system). Use the controls (1–6) to select the desired CD.
2. Press DEST . The warning screen will appear . After reading, press AGREE. The screen will show a map with your current location. Press DEST again. 3. Select the desired type of destination entry . Y ou may select “Address”, “Point of Interest”, “Emergency” or “Previous Dest” from the first screen.
4. Press DEST at the bottom of the map screen. 5. Choose the desired route by pressing the NEXT button (if it appears). There can be up to three alternative routes. 6. Press ST ART to begin the navigation guidance. T o adjust the voice guidance volume: 1.
Press VOICE briefly (on your steering wheel controls) and the voice icon appears on the Navigation display . Press REPEA T to hear the previous command repeated from the navigation system. The voice activated command feature will not operate if a map DVD is not inserted into the navigation DVD unit.
Commands that jump over screens: • Current position • Current location • Map While in navigation map mode, the following commands are available: • Zoom in • Zoom out • Minimum scale • Ma.
• Chinese food • Continental restaurant • Continental food • French restaurant • French food • Italian restaurant • Italian food • Japanese restaurant • Japanese food • Mexican res.
• Change to arrow guidance • Change to arrow guide • T urn list guidance • T urn list guide • Change to turn list guidance • Change to turn list guide • Entire route map • Entire route.
V olume/power control Press knob to turn the audio system on/off. T urn to raise or lower volume. The levels will be displayed on the screen. T o activate the navigation mode, press MAP or DEST . T o adjust the navigation voice output level, select the NA V MENU button via the map screen.
3. SCV is located in the middle of the screen. Press to turn on. 4. Select setting 1 to 7 or turn off. The recommended level for the speed compensated volume is from level 1 through level 3. When activated, level 1 is the minimum setting and level 7 is the maximum setting.
Tune adjust Press TUNE to manually move down/up ( / ) the frequency band. In CD mode, press TRACK to select the previous/next ( / ). Scan Press SCAN for a brief sampling of all listenable stations and CD tracks. Press again to disable and remain on the current selection.
Starting autoset memory preset 1. Select a frequency band using AM/FM1/FM2. 2. Press AUTO SET . 3. When the first six strong stations are filled, the station stored in memory preset control 1 will start playing.
Traf fic function Select TRAFFIC for traffic information broadcast from certain stations which will automatically interrupt radio or CD playback at a preset volume level. T raffic information not available in most U.S. markets. Information feature Press INFO to view the frequency , call letters and PTY category of the selected FM station.
T o set/change PTY : Ensure that the RDS function is turned on. Press SET PTY to select from the following program types: • All • Classical • Country • Information • Jazz • Religious • Rock • Soft • To p 4 0 Once PTY has been programmed, press SEEK ( / ) or SCAN to initiate a search up or down the frequency .
Sound functions T o access settings for Bass, T reble, Balance, Fade, DSP (Digital Signal Programing), SCV (Speed Compensated V olume), and Occupancy modes: 1. Press AUDIO. 2. Press SOUND. 3. Select from Bass/T reb; Bal/Fade; DSP/SCV . 4. Press +/— to increase/decrease the levels.
Fade : Allows you to adjust the amount of sound emitted from the front and rear speakers. Balance : Allows you to adjust the sound distribution between the right and left speakers. SCV (Speed Compensated V olume): Automatically compensates for road wind and noise.
Satellite ready capability Y our Lincoln navigation system comes equipped with Satellite ready capability . The kit to enable Satellite reception is available through your Lincoln dealer . Detailed Satellite instructions are included with the dealer installed kit.
Loading a CD: 1. Press CD OPEN CLOSE on the bezel. 2. The navigation screen will fold down, allowing you access to the in-dash six CD system. 3. Press LOAD and the desired CD slot number . The indicator light will blink slowly at first, then quickly , signaling the system is ready .
After an allotted time, the screen will close automatically or you may press CD OPEN CLOSE on the bezel again. 6. Once the screen closes, the system will start playing the last CD loaded. Track Press / to advance to the next/previous track. Rewind/fast forward in CD mode Press to reverse or advance ( / ) in the current CD track.
Shuffle feature in CD mode When in CD (or CDDJ mode), press SHUFFLE to engage the shuffle feature. Press to select from shuffling between tracks (SHUFFLE TRACK) on the current CD or between all tracks on all CDs (SHUFFLE DISC). All tracks will be played in random order .
Map mode Map display information T o access the map display , press MAP on the bezel. Once pressed, the current map display will appear on the screen showing the current vehicle location. Zoom control When ’Zoom’ is pressed, the scale indicator is shown on the screen.
Additional map function buttons T o initiate the display of additional map function buttons, tap the map anywhere on the screen or press the MAP hard key . These additional features will disappear from the screen within five seconds unless pressed. • STORE - stores current vehicle location as a memory point.
• Minimize T ime/Distance • Use Major Roads • Use T oll Roads • Use Ferries Information function INFO will appear on the screen when you have calculated a destination. Press INFO for more information about the current destination, if available.
Destination symbol — Indicates the current route destination. Next turn symbol — Shows the next maneuver that will need to be taken on the current route. North up button — Indicates that the map is displayed with north to the top of the screen. Press to toggle between “North up” and “Heading up” map display states.
Home position symbol — Indicates the location on the map, currently stored as the home position. Stored location symbol — Indicates the location of a memory point. This is the default symbol used when the point is stored. (If desired, an icon of your own choice can be selected from the 15 icons available.
Route options (destination entered) Once in navigation mode and a route is currently active, press “Chng. route” to access the ROUTE OPTIONS screen. Choose from the following selections: • Detour : Press to select a detour around the current route.
Navigation set up The Navigation Set up screen will allow you to make adjustments to the navigation displays. Average speed settings Allows you to set approximate speeds you drive. These speeds enable the navigation system to aid in calculating timing for routes.
Restore system defaults Resets all system user -selectable options to the default (automatic) values (i.e. guidance, voice, search area and route preferences). Calibration This feature is helpful if the car has been towed, or if you notice it is not registering at the correct vehicle location on the map.
Display Options The Display Options screen will allow you make adjustments to the navigation display screen. Y ou can choose from: • Map Mode (Dual or Full) • Guidance Mode (Arrows or T urn list) .
On route scroll The system automatically scrolls through the entire planned navigation route either forwards or backwards. T o activate, press the arrow buttons at the bottom left of the map screen. V oice guidance/volume Allows you to turn the voice guidance option on/off and to determine the volume level of the guidance voice prompts.
Home T o set home for the first time: 1. Press MAP . 2. Press “Nav . Menu”. 3. Press “Stored Locations”. 4. Press “Home”. 5. Press “Add”.
6. Select the desired menu item you wish to set as Home (Address, Memory Point, Point of Interest, Previous Destination). 7. Enter the required details. 8. Press OK to set the home position. T o view home, press the home icon (house) on the Destination Entry screen.
T o view the set home position 1. Press MAP . 2. Press “Nav . Menu”. 3. Press “Stored Locations”. 4. Press “Home”. 5. Press “List”. 2006 Lincoln LS (dew) Owners Guide (post-2002-fmt) U.
Deleting a home location 1. Press MAP . 2. Press “Nav . Menu”. 3. Press “Stored Locations”. 4. Press “Home”. 5. Press “Delete”. 2006 Lincoln LS (dew) Owners Guide (post-2002-fmt) USA (.
6. Press YES to confirm. Special memory points There are five possible special memory points that you can set. T o set a memory point: 1. Press the MAP hard key .
3. Press “Stored Locations”. 4. Press “Special Memory”. 5. Press “Add” and select a position. 6. Select point 1–5. 7. Input a destination. 8. Press OK. Once all five special memory points are entered, the “Add” control will read as “Full”.
3. Press “Stored Locations”. 4. Press “Special Memory”. 5. Press “Delete”. The list will display . 6. Select the special memory point to delete. 7. Press “Del. all” to delete all entered special memory points. 8. Press “Y es” to confirm.
Press DETOUR to activate. Use the soft controls to select and enter the number of miles you want to deviate off of the current road. Press DETOUR to confirm the selection and to activate the detour around the specified areas. Press NEW ROUTE if you would like the system to plan a different route.
Avoiding an area while under guidance For one reason or another , you may choose to avoid a certain area while in route to your destination. T o select the area to avoid: • From the MAP screen, press Nav Menu.
Deleting areas to avoid T o delete a selection from the “A void area” list: • From the stored locations menu, select “A void area”. • Press DELETE • Select the desired area to be deleted. • Press DEL. ALL to delete all stored areas. • Press YES to confirm.
Initial map display After pressing AGREE to the initial W ARNING screen, you will move into the initial map screen which shows the current vehicle location. Pressing the globe icon will take you to the user settings — audible feedback, navigation units, language and clock (if equipped).
Ensure that you follow highway code restrictions and do not take any risks. For example, if you are unable to make a U-turn, continue on your journey . The navigation system will recalculate your route to get you back to an appropriate road to your destination.
Search area The mapped areas covered by your map DVD are reflected in the Search Area map that is displayed on the Destination Entry screen. Y our navigation system uses a regional search area. This area is the area from which navigational directions will be used.
Points of interest (POI) Select “Point of Interest” from the Destination Entry Menu. In this next menu, you will have the following options: • By Name — Enter POI name on the keyboard. T ouch “List” to display the list of matching points of interest.
Deleting stored locations Y our navigation system allows you to delete any stored locations (previous destinations, memory points, special memory points, home, avoid areas, destination and way points, etc.) T o delete any of these stored locations: 1.
4. Select the desired item you wish to delete (previous destination, memory point, etc.). 5. Press “Delete” at the bottom of the screen. 6. The list of stored locations will be displayed. 7. Select (touch) the entry to be deleted. The item details will be listed.
Adding a memory point Y ou may add more memory points to be stored in the system. 1. W ith the map displayed, touch your finger to the screen to scroll to the desired location. When you reach the desired location, remove your finger from the screen and the map will stop scrolling.
4. Select “Memory Point”. 5. Press “Add” at the bottom of the screen. 6. Select the desired menu item. 7. Enter/select any required details. The new point will be added to the stored list of memory points. 8. Press OK. The new point will be added to the list of stored memory points.
3. Press “Stored locations”. 4. Press “Memory Point”. 5. Press LIST 6. Select the desired entry to view its location details. Sorting memory point lists 1. Access the desired list. 2. Press the button to sort the list as desired (i.e. date, name, or icon).
current vehicle location. When sorting by icon, the icons are listed in the order they appear on the icon selection screen. Choosing from the icon list After selecting a location, press ICON to edit. There will be 15 normal and three sound icons displayed.
Freeway Entrance/Exit T o set a freeway entrance or exit as a destination: 1. Press the DEST hard key . 2. Press “ Next page” to access the second page of the Destination Entry menu. 3. Select “Freeway Entrance/Exit”. 1. Enter freeway name — Enter the freeway name using the keyboard.
Destination and way points The Store Dest. & W ay Point menu is used after a destination or way point has been entered for the first time using the Destination Entry menu. Y ou can store and delete destinations and way points (locations you wish to visit in route to your ultimate destination).
Editing and changing order of way points and destination Press “Chg. Order” to change the order in which the way points are visited. The points are listed chronologically from bottom up, the destination being on the top. Press the MAP button to edit the way point location on the map display .
Route calculation Once the route criteria is selected, the navigation system automatically calculates the selected destination. The route appears on the display screen and a voice prompt provides instructions. The system may calculate up to four routes for the desired destination.
Menu mode T o access menu mode, press the MENU hard control. Menu mode allows you to access: • System Set-up • Information — Gives you the Lincoln Customer Assistance Center information. • Brightness/Contrast — Allows you to adjust the brightness and contrast on the screen.
• Screen off — Allows you to turn off the navigation screen. System setup The system set up menu contains the following user settings: • Audible Feedback — Press to activate audible voice navigation commands. Press again to deactivate. • Navigation Units — Press to toggle between Metric/English units.
General information Safety information Please read and follow all stated safety precautions. Failure to do so may increase your risk of collision and personal injury . Ford Motor Company shall not be liable for any damages of any type arising from failure to follow these guidelines.
Do not disassemble or modify the system as this may lead to damage and void your warranty . If a problem occurs, stop using the system immediately and contact your Ford or Lincoln Dealer .
traffic lights and thunderstorms. Moving away from an interfering structure (out of its “shadow”) returns your reception to normal. • Station overload.
• Not harmful but not recommended- ammonia cleaner , neutral detergent. • Harmful to system and not recommended- acid cleaner , alkali cleaner , benzene cleaner . Do not clean any part of the system with benzene, paint thinner or any other solvent.
DUAL AUTOMATIC T EMPERATURE CONTROL (DA TC) SYSTEM (IF EQUIPPED) 1. A/C control: Press to turn on and manually control the air conditioning. Press again to disengage. Press AUTO for the system to automatically control the temperature. 2. Recirculation control: Press to engage/disengage.
5. DUAL zone selector: Press to toggle the system between single zone and dual zone control. 6. (Defrost): Distributes outside air through the windshield defroster ducts and the demister outlets. Can be used to clear ice or fog from the windshield. The system will automatically provide outside air to reduce window fogging.
15. Fan Speed: Press to manually increase/decrease fan speed. In manual mode, the display will show with a bar graph to indicate fan speed. Fan speed can be manually adjusted in AUTO mode. T o allow the system to automatically control fan speed, press AUTO.
1. A/C control: Press to turn on and manually control the air conditioning. Press again to disengage. Press AUTO for the system to automatically control the temperature. 2. Recirculation control: Press to engage/disengage. Used to manually enable or disable recirculated air operation.
8. Airflow direction control: Press to toggle through the air distribution modes listed below . The selected mode will illuminate in the display . : Distributes air through the windshield defroster ducts, demister outlets and the front and rear seat floor ducts.
show . This allows the seats to automatically heat or cool based on the climate control temperature selected. Press either control to disengage. 14. Driver’ s side temperature control: Controls the temperature on the driver side of the vehicle in dual zone and controls the temperature of the entire vehicle in single zone.
A/C, recirculation controls, set the temperature to 60 °F (16 °C) and the fan to highest blower setting. • T o improve the A/C cool down, drive with the windows slightly open for 2-3 minutes after start up or until the vehicle has been “aired out.
Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop. REAR WINDOW DEFROSTER Press the rear window defroster control to clear the rear window and sideview mirrors of thin ice or fog. The light above the control will illuminate to indicate that the rear defrost is operating.
HEADLAMP CONTROL T urns the lamps off. T urns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. T urns the headlamps on. Autolamp control The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control.
High beams Pull toward you until control stops to activate. Repeat to deactivate. Flash to pass Pull toward you slightly to activate and release to deactivate. Daytime running lamps (DRL) (if equipped) T urns the highbeam headlamps on with a reduced output.
Foglamp control (if equipped) The foglamps can be turned on when the headlamp control is pulled toward you and is in any of the following positions: • Parking lamps • Low beams • Autolamps (when active) Foglamps will turn off when the highbeams are activated.
HEADLAMP VERTICAL AIM ADJUSTMENT Y our vehicle is equipped with VOL (Visual Optical Left) headlamps. 1. Park the vehicle directly in front of a wall or screen on a level surface, approximately 25 feet (7.6 meters) away . • (1) 8 feet (2.4 meters) • (2) VOL - subtract 2.
TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. INTERIOR LAMPS Map lamps The map lamps and controls are located on the dome lamp. Press the controls in front of each map lamp to activate the lamps.
Replacing exterior bulbs Check the operation of all the bulbs frequently . Using the right bulbs Replacement bulbs are specified in the chart below . Headlamp bulbs must be marked with an authorized “D.O.T .” for North America and an “E” for Europe to ensure lamp performance, light brightness and pattern and safe visibility .
Map lamps For bulb replacement, see a qualified service technician or your dealer . Replacing headlamp bulbs The headlamp assembly contains the low beam bulb, the high beam bulb, park/turn lamp bulb and led side marker . T o replace any of these bulbs, see your authorized dealer .
Replacing license plate lamp bulbs 1. Make sure the headlamp switch is in the OFF position. 2. Remove the screw from the license plate lamp assembly and pull it down. 3. Remove bulb socket by turning counterclockwise. 4. Carefully pull the bulb out from the socket.
MULTI-FUNCTION LEVER W indshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. W indshield washer: Push the end of the stalk: • Quickly pressing the end of the stalk switch causes a single wipe without washer fluid.
Easy entry/exit feature When you remove the key , the column will move, if this feature is activated through the Message Center , to the full in and up position, refer to the Message Center in the Driver Controls chapter . When the key is inserted into the ignition, the column will return to the previous setting.
ILLUMINATED VISOR MIRROR T o turn on the visor mirror lamps, lift the mirror cover . Adjust the amount of light by sliding the control. CENTER CONSOLE Y our vehicle may be equipped with a variety of console features.
ASHTRAY In order to prevent damage, follow these instructions when removing/installing the ashtray . Removal: 1. Push the ashtray face to slide open. Note: Do not remove the ashtray drawer . 2. Pull the ashtray insert upward from the ashtray drawer and remove.
AUXILIARY POWER POINT (12VDC) Power outlets are designed for accessory plugs only . Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse. Do not hang any type of accessory or accessory bracket from the plug.
When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings. Press the rocker switches to open and close windows. • Press the bottom portion of the rocker switch to open.
rocker switch to the Express Up position, hold the switch until the glass reaches the stall position and continue to hold for 2 seconds. Accessory delay W ith accessory delay , the window switches may be used for up to ten minutes after the ignition switch is turned to the OFF position or until either front door is opened.
Ensure the mirror is pulled down low enough to prevent visibility interference with the overhead console. The mirror support arm has two pivot points which lets you adjust the mirror UP or DOWN and from SIDE to SIDE.
Compass zone adjustment 1. Determine which compass zone you are in by referring to the zone map. 2. T urn the ignition to the ON/RUN position. 3. Press and hold the control for no more than six seconds until the zone selection number appears in the mirror display window .
POWER SIDE VIEW MIRRORS T o adjust your mirrors: 1. Select to adjust the left mirror or to adjust the right mirror . 2. Move the disk control in the direction you wish to tilt the mirror . 3. Return to the center position to disable the adjust function.
POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedal should only be adjusted when the vehicle is stopped and the gearshift lever is in the P (Park) position. Press and hold the rocker control (located on the instrument panel) to adjust accelerator and brake pedal.
Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release it. 2. Accelerate to the desired speed. 3. Press the SET + control and release it. 4. T ake your foot off the accelerator pedal.
Resuming a set speed Press the RES control and release it. This will automatically return the vehicle to the previously set speed. The RES control will not work if the vehicle speed is not faster than 30 mph (48 km/h).
• Depress the brake pedal until the desired vehicle speed is reached, press the SET + control. Turning of f speed control There are two ways to turn off the speed control: • Depress the brake pedal . This will not erase your vehicle’ s previously set speed.
In AM, FM1, or FM2 mode: • Press ⌬ or ⵜ to select preset stations within the selected radio band. In T ape mode: • Press ⌬ or ⵜ to select the next selection on the tape. In CD mode: • Press ⌬ or ⵜ to select the next selection on the CD.
Navigation steering wheel controls (if equipped) These controls allow you to operate some audio and navigation control features when the vehicle is equipped with the navigation feature. Audio control features Press MEDIA to select: • AM, FM1, FM2, or • CD.
Navigation control features Press and hold VOICE until the voice icon appears to use the navigation voice guidance. Press REPEA T control to hear previous command repeated from the navigation system. MOON ROOF (IF EQUIPPED) T o open the moon roof: • Push up on the control to raise the moon roof to the vent position.
• T o close from the vent, intermediate and full open positions, push the rear portion of the control forward. Do not let children play with the moon roof or leave children unattended in the vehicle.
U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982). A garage door which cannot detect an object, signaling the door to stop and reverse, does not meet current U.S. federal safety standards. For more information, contact HomeLink 威 at: www .
4. The indicator light will flash slowly and then rapidly . Release both buttons when the indicator light flashes rapidly . (The rapid flashing light indicates acceptance of the hand-held transmitters’ radio frequency signals.) 5. Press and hold the just-trained HomeLink 威 button and observe the indicator light.
• Continue to press and hold the HomeLink 威 button (note Step 3 in the “Programming” section) while you press and release — every two seconds (“cycle”) your hand-held transmitter until the frequency signal has been accepted by the HomeLink 威 .
2. The indicator light will begin to flash after 20 seconds. W ithout releasing the HomeLink 威 button, follow Step 2 in the “Programming” section.
MESSAGE CENTER (IF EQUIPPED) W ith the ignition in the RUN position, the message center , located on your instrument cluster , displays important vehicle information by monitoring vehicle systems. When you change displays, a brief indicator chime will sound.
The sequence of the status check report is as follows: • washer fluid level • oil life in XX% • AC (cabin) filter XX% • engine temperature • brake fluid level • charging system • doors closed (driver and passenger side, front and rear). This message can only be reset by closing the door(s).
Fuel Econ Avg Select this function from the FUEL control to display your average fuel economy in miles/gallon or liters/ 100 km. If you calculate your average fuel economy by dividing gallons of fuel .
It is important to press the RESET control after setting the speed control to get accurate highway fuel economy readings. Display On/Off Select this function from the FUEL control to turn your message center display OFF or ON. Units (English/Metric) 1.
Language 1. Select this function from the SETUP control for the current language to be displayed. 2. Pressing the RESET control cycles the message center through each of the language choices. 3. Press and hold the RESET control to set the language choice.
W arnings Status Engine power reduced W arning cannot be reset Pull off road safely T urn off ignition Driver’ s door ajar Passenger door ajar Driver rear door ajar Passenger rear door ajar Park bra.
W arnings Status Low brake fluid level W arning returns after the ignition key is turned from OFF to RUN Check tail lamps Check brake lamps Check front turn lamps Check side repeater lamps (if equippe.
P ASSENGER REAR DOOR AJAR. Displayed when the passenger side rear door is not completely closed. P ARK BRAKE ON & NEED SER VICE. Displayed when the park brake is ON and malfunctioning. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible.
ETC-ENGINE F AILSAFE MODE. Displayed when the engine has defaulted to a ’limp-home’ operation. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. LOW BRAKE FLUID. Indicates the brake fluid level is low and the brake system should be inspected immediately .
CHECK A/C (cabin) FIL TER. Displayed when the A/C cabin filter life remaining is 5 percent or less. When A/C filter life left is between 5% and 0%, the CHANGE A/C FIL TER SOON message will be displayed. When A/C filter life left reaches 0%, the A/C FIL TER CHANGE REQUIRED message will be displayed.
2. Press and hold the RESET control to set to 100%. 3. After a successful reset, the message center will display OIL LIFE SET TO 100%. SER VICE PARK BRAKE. Displayed when the park brake needs servicing. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible.
INTERIOR TRUNK CONTROL Press the remote trunk release control on the instrument panel to open the trunk. Y ou can render the switch inoperable by locking the button with your master key .
POSITIVE RETENTION FLOOR MA T Do not install additional floor mats on top of the factory installed floor mats as they may interfere with the accelerator or the brake pedals. Position the driver floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in.
KEYS Y our vehicle is equipped with two master keys and a valet key lock system. The master key will access the driver’ s door , trunk, glove box, remote trunk release control and ignition.
seconds to begin to open all the windows and moonroof. Releasing the control on the remote entry transmitter , or returning the key to the center position will stop all motion. Note: The ignition must be in the 2 (OFF) position and the accessory delay feature must not be activated in order for this feature to operate.
CHILDPROOF DOOR LOCKS • When these locks are set, the rear doors cannot be opened from the inside. • The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on the rear edge of each rear door and must be set separately for each door .
T o open the luggage compartment door (lid) from within the luggage compartment, pull the illuminated “T” shaped handle and push up on the trunk lid. The handle is composed of a material that will glow for hours in darkness following brief exposure to ambient light.
REMOTE ENTRY SYSTEM This device complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Unlocking the doors 1. Press and release to: • unlock the driver’ s door only , if the two-stage unlocking feature is enabled. • unlock all doors, if the two-stage unlocking feature is disabled. • deactivate the perimeter alarm (if activated).
Locking the doors 1. Press and release to lock all the doors and arm the perimeter alarm system (also enables the ignition tamper security system). • Note: W ith the first press of the control, the turn signal lamps will flash once to confirm the doors, trunk and hood are closed.
T o replace the battery: 1. T wist a thin coin between the two halves of the remote entry transmitter near the key ring. DO NOT T AKE THE RUBBER COVER AND CIRCUIT BOARD OFF THE FRONT HOUSING OF THE REMOTE ENTRY TRANSMITTER. 2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board.
How to reprogram your remote entry transmitters Y ou must have all remote entry transmitters (maximum of four) available before beginning this procedure. T o reprogram the remote entry transmitters: 1. Ensure the vehicle is electronically unlocked. 2.
The battery saver feature will turn off the interior lamps 40 minutes after the ignition is turned to the 1 (LOCK) or 2 (OFF) position. Autolock The autolock feature will lock the vehicle’ s doors w.
2. Press the SET control on the driver’ s door panel. 3. W ithin 5 five seconds, press any control on the remote transmitter and then press the 1 or 2 control on the driver’ s door panel to associate with the Driver 1 or Driver 2 positions. 4. Repeat this procedure for another remote transmitter if desired.
3. Enter your personal 5-digit code. Each number must be entered within five seconds of each other . 4. Enter a sixth digit to indicate which personality feature should be recalled by the personal code. Note: The lock motors will cycle, locked then unlocked.
• pressing the UNLOCK control on the remote entry transmitter . • the ignition is turned to the 4 (RUN) position. Unlocking and locking the doors using keyless entry T o unlock the driver’ s door , enter the factory set 5-digit code or your personal code.
key chain may cause vehicle starting issues. Y ou need to prevent these objects from touching the coded key while starting the engine. These objects will not cause damage to the coded key , but may cause a momentary issue if they are too close to the key when starting the engine.
1. Insert the first previously programmed coded key into the ignition from 1 (LOCK) to 4 (RUN) (maintain ignition in the 4 (RUN) position for at least three seconds, but no more than ten seconds). 2. T urn the ignition to the 1 (LOCK) position and remove the first coded key from the ignition.
The system is ready to arm whenever key is removed from the ignition. Any of the following actions will prearm the alarm system: • Press the control on the remote entry transmitter . • Press the driver or passenger interior power door lock control while that respective door is open, then close the door .
SEATING Notes: Reclining the seatback can cause an occupant to slide under the seat’ s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop.
Push control to lower head restraint. Using the manual lumbar support (if equipped) The lumbar control is located on the front of the seat cushion. T urn to adjust lumbar support. Using the power lumbar support (if equipped) The power lumbar control is located on the outboard side of the seat.
Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can cause an occupant to slide under the seat’ s safety belt, resulting in severe personal injuries in the event of a collision.
Move front/rear of control up or down to tilt the front/rear of the seat cushion. • Driver Easy entry/easy exit feature (if equipped) This feature automatically moves the driver’ s seat backward 5 cm (2 inches) when the key is removed from the ignition cylinder .
The memory seat positions are also recalled when you press your remote entry transmitter UNLOCK control and the transmitter is programmed to a memory seat position or when you enter a valid customer code 1 or 2 on the keypad. T o program the memory seat to remote entry transmitter , refer to Remote entry system in the Locks and security chapter .
T o remove an air filter: • Remove key from ignition. • Push up on the outside rigid edge of the filter and rotate toward the front of the vehicle once tabs are released. • Remove filter . T o install a filter: • First, position the filter in it’ s housing making sure that the far forward end is all the way up in the housing.
The head restraints can be moved up and down. Push control to lower head restraint. Rear heated seats (if equipped) • Push the indicated side of the button for low heat. • Push again to deactivate. • Push the indicated side of the button for high heat.
The heated seats will activate when the ignition is in the RUN position. When activated, they will turn off automatically after 10 minutes or when the ignition is turned to the OFF position. The indicator lights will illuminate when each heated seat has been activated.
SAFETY RESTRAINTS Personal Safety System 姟 The Personal Safety System 娂 provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of airbag-related injuries.
Driver and passenger dual-stage airbag supplemental restraints The dual-stage airbags offer the capability to tailor the level of airbag inflation energy . A lower , less forceful energy level is provided for more common, moderate-severity impacts. A higher energy level is used for the most severe impacts.
Front safety belt energy management retractors The front safety belt energy management retractors allow webbing to be pulled out of the retractor in a gradual and controlled manner in response to the occupant’ s forward momentum. This helps reduce the risk of force-related injuries to the occupant’ s chest by limiting the load on the occupant.
Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. All occupants of the vehicle, including the driver , should always properly wear their safety belts, even when an airbag supplemental restraint system (SRS) is provided.
Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. 2. T o unfasten, push the release button and remove the tongue from the buckle.
The front outboard and rear safety restraints in the vehicle are combination lap and shoulder belts. The front passenger and rear seat safety belts have two types of locking modes.
This mode should be used any time a child safety seat is installed in the vehicle. Children 12 years old and under should be properly restrained in the rear seat whenever possible. Refer to Safety restraints for children or Safety seats for children later in this chapter .
Front safety belt height adjustment The driver and front seat outboard positions are equipped with a height adjuster . Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder . T o adjust the shoulder belt height, push the button and slide the height adjuster up or down.
Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the RUN position... The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds.
If... Then... The driver’ s safety belt is buckled before the ignition switch is turned to the ON position... The BeltMinder 威 feature will not activate. The following are reasons most often given for not wearing safety belts (All statistics based on U.
Reasons given... Consider ... “The people I’m with don’t wear belts” Set the example, teen deaths occur 4 times more often in vehicles with TWO or MORE people. Children and younger brothers/sisters imitate behavior they see. “I have an airbag” Airbags offer greater protection when used with safety belts.
T o reduce the risk of injury , do not deactivate/activate the Belt Minder feature while driving the vehicle. 1. T urn the ignition switch to the RUN (or ON) position.
Safety belt maintenance Inspect the safety belt systems periodically to make sure they work properly and are not damaged. Inspect the safety belts to make sure there are no nicks, tears or cuts.
Important SRS precautions The SRS is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries.
Do not attempt to service, repair , or modify the airbag supplemental restraint systems or its fuses. See your authorized dealer . Modifying or adding equipment to the front end of the vehicle (including frame, bumper , front end body structure and tow hooks) may affect the performance of the airbag system, increasing the risk of injury .
How does the safety belt pretensioner and airbag supplemental restraint system work? The safety belt pretensioner and airbag SRS are designed to activate when the vehicle sustains longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates pretensioner activation and airbag inflation.
are not properly restrained or are otherwise out of position at the time of airbag deployment. Thus, it is extremely important that occupants be properly restrained as far away from the airbag module as possible while maintaining vehicle control. Several air bag system components get hot after inflation.
• A series of five beeps will be heard. The tone pattern will repeat periodically until the problem and/or light are repaired. If any of these things happen, even intermittently , have the SRS serviced at an authorized dealer immediately . Unless serviced, the system may not function properly in the event of a collision.
How does the side airbag system work? The side airbag system consists of the following: • An inflatable nylon bag (airbag) with a gas generator concealed behind the outboard bolster of the driver and front passenger seatbacks. • A special seat cover designed to allow airbag deployment.
If the side airbag has deployed, the airbag will not function again. The side airbag system (including the seat) must be inspected and serviced by an authorized dealer . If the airbag is not replaced, the unrepaired area will increase the risk of injury in a collision.
Do not place objects or mount equipment on or near the airbag cover on the side of the seatbacks of the front seats or in front seat areas that may come into contact with a deploying airbag. Failure to follow these instructions may increase the risk of personal injury in the event of a collision.
All occupants of the vehicle, including the driver , should always wear their safety belts even when an inflatable curtain is provided. T o reduce the risk of injury , do not obstruct or place objects in the deployment of the inflatable curtain.
The side air curtains are mounted to the sheet metal above the first and second row seats. In certain lateral collisions, the air curtain and seat-mounted side airbag on the side affected by the collision will be inflated, even if the respective seat is not occupied.
Any difficulty with the system is indicated by one or more of the following: • The readiness light (same light as used for front airbag system) will either flash or stay lit. • The readiness light will not illuminate immediately after ignition is turned to the RUN position.
Children and safety belts If the child is the proper size, restrain the child in a safety seat. Children who are too large for child safety seats (as specified by your child safety seat manufacturer) should always wear safety belts. Follow all the important safety restraint and airbag precautions that apply to adult passengers in your vehicle.
• Can the child sit all the way back against the vehicle seat back with knees bent comfortably at the edge of the seat without slouching? • Does the lap belt rest low across the hips? • Is the s.
Children and booster seats vary widely in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder .
Never use pillows, books, or towels to boost a child. They can slide around and increase the likelihood of injury or death in a collision. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child.
and anchors, refer to Attaching safety seats with tether straps in this chapter . For more information of LA TCH anchors refer to Attaching safety seats with LA TCH (Lower Anchors and T ethers for Children) attachments in this chapter . Carefully follow all of the manufacturer’ s instructions included with the safety seat you put in your vehicle.
2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions.
5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is pulled out and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode.
Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point. T ether straps are available as an accessory for many older safety seats.
4. Open the tether anchor cover . 5. Clip the tether strap to the anchor as shown. If the tether strap is clipped incorrectly , the child safety seat may not be retained properly in the event of a collision. 6. Install the child safety seat tightly using the LA TCH anchors or safety belts.
Y our vehicle has LA TCH anchors for child seat installation at the seating positions marked with the child seat symbol. The anchors on both sides of the center of the rear seat are provided primarily for child seats at the outboard seats, and are further apart than the pairs of lower anchors for child seat installation at other seats.
The lower anchors for child seat installation are recessed at the rear section of the rear seat between the cushion and seat back. The LA TCH anchors are located below and behind the locator symbols on the seat back. Follow the child seat manufacturer’ s instructions to properly install a child seat with LA TCH attachments.
INFORMA TION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tires that have a rating on them called T ire Quality Grades. The Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width.
The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics.
• kPa: Kilopascal, a metric unit of air pressure. • PSI: Pounds per square inch, a standard unit of air pressure. • Cold inflation pressure: The tire pressure when the vehicle has been stationary and out of direct sunlight for an hour or more and prior to the vehicle being driven for 1 mile (1.
Use the recommended cold inflation pressure for optimum tire performance and wear . Under -inflation or over -inflation may cause uneven treadwear patterns.
Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressure when you get to the pump. It is normal for tires to heat up and the air pressure inside to go up as you drive.
Tire wear When the tread is worn down to 1/16th of an inch (2 mm), tires must be replaced to help prevent your vehicle from skidding and hydroplaning. Built-in treadwear indicators, or “wear bars”, which look like narrow strips of smooth rubber across the tread will appear on the tire when the tread is worn down to 1/16th of an inch (2 mm).
built. For example, the numbers 317 mean the 31st week of 1997. After 2000 the numbers go to four digits. For example, 2501 means the 25th week of 2001. The numbers in between are identification codes used for traceability . This information is used to contact customers if a tire defect requires a recall.
Highway hazards No matter how carefully you drive there’ s always the possibility that you may eventually have a flat tire on the highway . Drive slowly to the closest safe area out of traffic. This may further damage the flat tire, but your safety is more important.
• Rear Wheel Drive (RWD) vehicles/Four Wheel Drive (4WD)/ All Wheel Drive (A WD) vehicles (front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires.
Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below . (Note that the tire size, load index and speed rating for your vehicle may be different from this example.
Note: Y ou may not find this information on all tires because it is not required by federal law . Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R .
12. T readwear , T raction and T emperature Grades • T readwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course.
Additional information contained on the tire sidewall for “L T” type tires “L T” type tires have some additional information beyond those of “P” type tires; these differences are described below: 1. LT: Indicates a tire, designated by the T ire and Rim Association (T&RA), that is intended for service on light trucks.
Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example.
SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires you currently have on your vehicle. The tires on your vehicle have all weather treads to provide traction in rain and snow . However , in some climates, you may need to use snow tires or chains.
Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the T ire Label on the B-Pillar or the edge of the driver’ s door (vehicles exported outside the US and Canada may not have a T ire Label).
Example only: Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload.
located on the B-Pillar or the edge of the driver’ s door . The total load on each axle must never exceed its GA WR. Exceeding the Safety Compliance Certification Label axle weight rating limits cou.
Do not use replacement tires with lower load carrying capacities than the originals because they may lower the vehicle’ s GVWR and GA WR limitations. Replacement tires with a higher limit than the originals do not increase the GVWR and GA WR limitations.
the vehicle with the rear seat folded down, you have room for 12-100 lb. (45 kg) bags of cement. Do you have enough load capacity to transport the cement to your home? If you and your friend each weigh 220 lb. (99 kg), the calculation would be: 1400 – (2 x 220) – (12 x 100) = 1400 – 440 – 1200 = – 240 lb.
• Place the transmission in N (Neutral) • Maximum speed is 35 mph (56 km/h) • Maximum distance is 50 miles (80 km) If a distance of 50 miles (80 km) or a speed of 35 mph (56 km/h) must be exceeded, you must disconnect the driveshaft. Ford recommends the driveshaft be removed/installed only by a qualified technician at an authorized dealer .
STARTING Positions of the ignition 1. LOCK, locks the gearshift lever and allows key removal. (The steering wheel will not lock after key removal.) 2. OFF , shuts off the engine and all accessories without locking the steering wheel.
Do not park, idle, or drive your vehicle in dry grass or other dry ground cover . The emission system heats up the engine compartment and exhaust system, which can start a fire. Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic.
• T urn the key to 4 (ON) without turning the key to 5 (ST ART). Some warning lights will briefly illuminate. See W arning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the engine Note: Whenever you start your vehicle, release the key as soon as the engine starts.
Important ventilating information If the engine is idling while the vehicle is stopped for a long period of time, open the windows at least one inch (2.
ABS warning lamp The ABS lamp in the instrument cluster momentarily illuminates when the ignition is turned on. If the light does not illuminate during start up, remains on or flashes, the ABS may be disabled and may need to be serviced. Even when the ABS is disabled, normal braking is still effective.
The BRAKE warning lamp will illuminate and will remain illuminated until the parking brake is released. The parking brake will automatically disengage when the gearshift lever is moved from P (Park) with the ignition in the ON position or if the engine is running.
If the T raction Control system is activated excessively in a short period of time, the brake portion of the system will shut down to allow the brakes to cool down. A limited T raction Control function using only engine power reduction will still help control the wheels from over -spinning.
Driving conditions which may activate AdvanceT rac 威 include: • T aking a turn too fast • Maneuvering quickly to avoid an accident, pedestrian or obstacle • Hitting a patch of ice • Changing.
sand or very deep snow , switching off the AdvanceT rac 威 stability enhancement feature will restore full engine power and will enhance momentum through the obstacle. Some drivers may notice a slight movement of the brake pedal when the AdvanceT rac 威 performs a system self-check.
If the power steering system breaks down (or if the engine is turned off), you can steer the vehicle manually , but it takes more effort. If the steering wanders or pulls, check for: • an improperly.
If it is necessary to use the above procedure to move the gearshift lever , it is possible that a fuse has blown or the vehicle’ s brakelamps are not operating properly . Refer to Fuses and relays in the Roadside Emergencies chapter . Do not drive your vehicle until you verify that the brakelamps are working.
P (Park) This position locks the transmission and prevents the rear wheels from turning. T o put your vehicle in gear: • Start the engine • Depress the brake pedal • Move the gearshift lever int.
3 (Third) This position allows for third gear only . • Provides engine braking. • T o return to D5 or D4, move the transmission shift lever into the D5 or D4 position. • Selecting 3 (Third) at higher speeds will cause the transmission to downshift to third gear at the appropriate vehicle speed.
Automatic shift mode Operates like a normal automatic transmission for P (Park), R (Reverse), N (Neutral), D5 and D4. Refer to Driving with a 5–speed automatic transmission in this chapter for P (Park), R (Reverse), N (Neutral), D5 and D4 information.
• One tap rearward (-) will command the transmission to downshift one gear range. • Upshifts are allowed at any vehicle speed, with the exception of 4th and 5th gear . The transmission will not do a 4th or 5th gear start. Ensure that the transmission is returned to 1st gear once the vehicle is stopped.
REAR PARK ASSIST (IF EQUIPPED) The rear park assist system sounds a tone to warn the driver of obstacles near the rear bumper when the R (Reverse) gear is selected. T o help avoid personal injury , please read and understand the limitations of the rear park assist system as contained in this section.
The system detects obstacles within approximately 16 feet (5 meters), at speeds above 2 mph [3 km/h]), behind the rear bumper with a decreased coverage area at the outer corners of the bumper .
If the vehicle sustains damage to the rear bumper/fascia, leaving it misaligned or bent, the sensing zone may be altered causing inaccurate measurement of obstacles or false alarms. DRIVING THROUGH WATER If driving through deep or standing water is unavoidable, proceed very slowly especially when the depth is not known.
ROADSIDE ASSISTANCE Getting roadside assistance T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program.
Canadian customers refer to your Owner Information Guide for information on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement .
HAZARD FLASHER The hazard flasher is located on the steering column, just behind the steering wheel. The hazard flashers will operate when the ignition is in any position or if the key is not in the ignition. Push in the flasher control and all front and rear direction signals will flash.
This switch is located in the driver’ s footwell, behind the kick panel. T o reset the switch: 1. T urn the ignition OFF . 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset the switch by pushing in on the reset button. 4. T urn the ignition ON.
Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A T an T an — — — 7.
The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 5A Starter relay coil 2 5A Radio 3 5A ABS/TCS/AdvanceT rac 威 4 5A Cluster , Powertr.
Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 10 5A Left front turn, Left front sidemarker , Left front park lamps 11 10A Left front high beam 12 5A Electrochromic m.
Front power distribution box The front power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’ s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses.
The high-current fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 1 10A* A/C clutch, Coolant control valve, Auxiliary coolant pump 2 — Not used 3 15.
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 13 30A** Heated wiper park 14 30A** ABS module 15 — Not used 16 30A** Blower motor 17 — Not used 18 — Not used 19 30A** Ele.
In-line fuse for electric cooling fan There is a 60A maxi fuse for the electric cooling fan located in a wiring harness behind the front passenger side trim panel under the dash panel. The trim panel must be removed and the carpet on the front passenger side must be lifted to access this fuse.
The high-current fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 1 15A* Decklid release solenoid, Passenger door lock motors 2 10A* Right rear turn l.
Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 17 15A* Fuel pump motor 18 20A* Subwoofer amp 30A* THX amp, Subwoofer amp 19 20A** REM - Left rear window 20 30A** Front window m.
• slowly move to a safe place on the side of the road. The use of tire sealants is not recommended and may damage your tires. Dissimilar spare tire/wheel information Failure to follow these guidelines could result in an increased risk of loss of vehicle control, injury or death.
• Comfort and noise • Ground clearance and parking at curbs • W inter weather driving capability • W et weather driving capability For vehicles equipped with 4WD, it is not recommended that the vehicle be operated in 4WD modes with a temporary emergency spare tire.
Tire change procedure T o help prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block (in both directions) the wheel that is diagonally opposite (other side and end of the vehicle) to the tire being changed.
4. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. 5. Put the jack in the jack notch next to the tire you are changing. T urn the jack handle clockwise until the wheel is completely off the ground.
Never use the rear differential as a jacking point. T o lessen the risk of personal injury , do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire.
When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum or brake disc that contacts the wheel. Ensure that any fasteners that attach the rotor to the hub are secured so they do not interfere with the mounting surfaces of the wheel.
4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables. Ensure the vent caps are tight and level. 5. T urn the heater fan on in both vehicles to protect any electrical surges. T urn all other accessories off.
3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . + – + – 2006 Lincoln LS (dew) Owners Guide (post-2002-fmt) USA (fus) Roadside Emergencies 256.
4. Make the final connection of the negative (-) cable to the spare tire tie-down stud. (Y our vehicle may be equipped with a plastic cap on top of the tire tie-down stud. This cap must be removed prior to attaching the cable to the stud.) Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped.
Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the spare tire tie-down stud. 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’ s battery .
3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery .
WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . It is recommended that your vehicle be towed with a wheel lift or flatbed equipment.
GETTING THE SERVICES YOU NEED At home Y ou must take your Lincoln or Mercury vehicle to an authorized dealer for warranty repairs. While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction.
In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www .ford.
In some states (in the U.S.) you must directly notify Ford in writing before pursuing remedies under your state’ s warranty laws. Ford is also allowed a final repair attempt in some states.
THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Y our satisfaction is important to Ford Motor Company and to your dealer . Experience has shown that our customers have been very successful in achieving satisfaction by following the three-step procedure outlined on the front page of the W arranty Guide.
authorized dealer to resolve a factory-related vehicle service concern have been unsatisfactory , Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor V ehicle Arbitration Plan (CAMV AP).
GETTING ASSIST ANCE OUTSIDE THE U.S. AND CANADA Before exporting your vehicle to a foreign country , contact the appropriate foreign embassy or consulate. These officials can inform you of local vehicle registration regulations and where to find unleaded fuel.
Or call: For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website: www .helminc.com. (Items in this catalog may be purchased by credit card, check or money order .
W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail W ash (ZC-3–A), which is available from your authorized dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid.
W AXING Applying Motorcraft Paint Sealant (ZC-45) to your vehicle every six months will assist in reducing minor scratches and paint damage. • W ash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft Premium Liquid W ax (ZC-53-A), which is available from your authorized dealer , or an equivalent quality product.
ENGINE Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: • T ake care when using a power washer to clean the engine. The high-pressure fluid could penetrate the sealed parts and cause damage.
• For plastic headlamp lenses, use Motorcraft Ultra Clear Spray Glass Cleaner (ZC-23). WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should be cleaned regularly . If the wipers do not wipe properly , substances on the vehicle’ s glass or the wiper blades may be the cause.
INTERIOR TRIM • Clean the interior trim areas with a damp cloth, then with a clean, dry cloth; you may also use Motorcraft Dash & Vinyl Cleaner (ZC-38-A).
leather conditioners. These products may cause premature wearing of the clear , protective coating. Note: In some instances, color or dye transfer can occur when wet clothing comes in contact with leather upholstery . If this occurs, the leather should be cleaned immediately to avoid permanent staining.
Motorcraft Premium W indshield W asher Concentrate (ZC-32–A) Motorcraft Professional Strength Carpet & Upholstery Cleaner (ZC-54) Motorcraft Spot and Stain Remover (U.S. only) (ZC-14) Motorcraft T ire Clean and Shine (ZC-28) Motorcraft T riple Clean (U.
SERVICE RECOMMENDATIONS T o help you service your vehicle: • W e highlight do-it-yourself items in the engine compartment for easy location. • W e provide scheduled maintenance information which makes tracking routine service easy .
OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located at the bottom left of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood by pushing upward on the handle.
IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.9L–4V V8 engine 1. Engine oil filler cap 2. Engine oil dipstick 3. Brake fluid reservoir 4. Engine coolant reservoir 5. Air filter assembly 6. Power steering fluid reservoir 7. W indshield washer fluid reservoir 8.
WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Ford specification WSB-M8B16–A2. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash.
2. Firmly press the release tab from the bottom side of the wiper arm to unlock wiper blade from wiper arm. 3. Pull the wiper blade down toward the windshield to remove it from the arm. 4. Attach the new wiper to the wiper arm and reposition the clip until it locks.
5. Locate and carefully remove the engine oil level indicator (dipstick). 6. W ipe the indicator clean. Insert the indicator fully , then remove it again. • If the oil level is between the MIN and MAX marks, or between the lower and upper holes (depending on application), the oil level is acceptable.
3. Recheck the engine oil level. Make sure the oil level is not above the MAX mark on the engine oil level indicator (dipstick). 4. Install the indicator and ensure it is fully seated. 5. Fully install the engine oil filler cap by turning the filler cap clockwise tightly until clicks are heard, or until it is snug.
It is recommended you use the appropriate Motorcraft oil filter (or another brand meeting Ford specifications) for your engine application. BATTERY Y our vehicle is equipped with a Motorcraft maintenance-free battery which is located in the luggage compartment, next to the spare tire.
When lifting a plastic-cased battery , excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery . Lift the battery with a battery carrier or with your hands on opposite corners.
If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected. • Always dispose of automotive batteries in a responsible manner . Follow your local authorized standards for disposal.
When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be at the “FULL COLD” level or within the “COLD FILL RANGE” as listed on the engine coolant reservoir (depending upon application).
Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly . Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluid container .
remove the coolant pressure relief cap on the radiator of a vehicle with an overflow system, follow these steps to add engine coolant. T o reduce the risk of personal injury , make sure the engine is cool before unscrewing the coolant pressure relief cap.
Used engine coolant should be disposed of in an appropriate manner . Follow your community’ s regulations and standards for recycling and disposing of automotive fluids. Coolant refill capacity T o find out how much fluid your vehicle’ s cooling system can hold, refer to Refill capacities in this section.
What you should know about fail-safe cooling If the engine coolant supply is depleted, this feature allows the vehicle to be driven temporarily before incremental component damage is incurred. The “fail-safe” distance depends on ambient temperatures, vehicle load and terrain.
4. Check the coolant level and replenish if low . Never remove the coolant reservoir cap while the engine is running or hot. 5. Re-start the engine and take your vehicle to an authorized dealer . Driving the vehicle without repairing the engine problem increases the chance of engine damage.
Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before refueling your vehicle. • Always turn off the vehicle before refueling. • Automotive fuels can be harmful or fatal if swallowed.
Refueling Fuel vapor burns violently and a fuel fire can cause severe injuries. T o help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • T urn off yo.
If you must replace the fuel filler cap, replace it with a fuel filler cap that is designed for your vehicle. The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used.
Fuel quality If you are experiencing starting, rough idle or hesitation driveability problems during a cold start, try a different brand of “Premium” unleaded gasoline.
Filling the tank The advertised fuel capacity of the fuel tank on your vehicle is equal to the rated refill capacity of the fuel tank as listed in the Refill capacities section of this chapter . The advertised capacity is the amount of the indicated capacity and the empty reserve combined.
5. Follow one of the simple calculations in order to determine fuel economy: Calculation 1: Divide total miles traveled by total gallons used. Calculation 2: Multiply liters used by 100, then divide by total kilometers traveled. Keep a record for at least one month and record the type of driving (city or highway).
Maintenance • Keep tires properly inflated and use only recommended size. • Operating a vehicle with the wheels out of alignment will reduce fuel economy . • Use recommended engine oil. Refer to Lubricant specifications in this chapter . • Perform all regularly scheduled maintenance items.
applicable exhaust emission standards. T o make sure that the catalytic converter and other emission control components continue to work properly: • Use only the specified fuel listed. • A void running out of fuel. • Do not turn off the ignition while your vehicle is moving, especially at high speeds.
On board diagnostics (OBD-II) Y our vehicle is equipped with a computer that monitors the engine’ s emission control system. This system is commonly known as the On Board Diagnostics System (OBD-II). This OBD-II system protects the environment by ensuring that your vehicle continues to meet government emission standards.
engine must warm up to its normal operating temperature. Once started, do not turn off the engine until the above driving cycle is complete. POWER STEERING FLUID Refer to the scheduled maintenance information for the service interval schedules. If adding fluid is necessary , use only MERCON 威 AT F.
T RANSMISSION FLUID Checking automatic transmission fluid The 5R55S transmission does not have a transmission fluid dipstick. Refer to your scheduled maintenance information for scheduled intervals for fluid checks and changes. Y our transmission does not consume fluid.
Changing the air filter element 1. Loosen the hose clamp on the outlet tube at the air filter housing. 2. Release the two clamps that secure the cover to the air filter housing and place the cover aside. 3. Remove the air filter element from the air filter housing.
5. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing and cover . This could cause filter damage and allow unmetered air to enter the engine if not properly seated. 6. Replace the air filter housing cover and secure the clamps.
MOTORCRAFT PART NUMBERS Component 3.9L-4V V8 engine Air filter element F A-1679 Fuel filter FG-1011 Battery BXT -66-650 Oil filter FL-2021 Spark plugs 1 1 For spark plug replacement, see your authorized dealer . Refer to scheduled maintenance information for the appropriate intervals for changing the spark plugs.
Fluid Ford Part Name Application Capacity Engine coolant 2 Motorcraft Premium Gold Engine Coolant (yellow-colored) All 11.9 quarts (11.3L) Power steering fluid Motorcraft MERCON 威 AT F All Fill to MAX line on reservoir Rear axle 3 Motorcraft SAE 75W -140 Rear Axle Lubricant All 2.
6 Use of synthetic or synthetic blend motor oil is not mandatory . Engine oil need only meet the requirements of Ford specification WSS-M2C930-A and the API Certification mark.
Item Ford part name Ford part number Ford specification Engine oil Motorcraft SAE 5W -20 Premium Synthetic Blend Motor Oil (US) Motorcraft SAE 5W -20 Super Premium Motor Oil (Canada) XO-5W20-QSP (US) .
ENGINE DATA Engine 3.9L-4V V8 engine Displacement 241 cid (3 949 cc) Required fuel 91 octane Firing order 1-5-4-2-6-3-7-8 Ignition system Coil on plug Spark plug gap 0.040–0.044 inch (1.0–1.1mm) Compression ratio 10.75:1 V EHICLE DIMENSIONS V ehicle dimensions Inches (mm) (1) Overall length 194.
IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located.
V ehicle identification number (VIN) The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel. Please note that in the graphic, XXXX is representative of your vehicle identification number . The V ehicle Identification Number (VIN) contains the following information: 1.
T RANSMISSION/T RANSAXLE CODE DESIGNATIONS Y ou can find a transmission/transaxle code on the Safety Compliance Certification Label. The following table tells you which transmission or transaxle each code represents.
LINCOLN ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Lincoln Accessories are available for your vehicle through your local Lincoln or Ford of Canada dealer .
Lifestyle Cargo organization and management Peace of mind Airbag anti-theft locks First aid and safety kits Full vehicle covers Engine block heaters Keyless entry keypad Mobile-Ease 娂 hands free com.
A Accessory delay ........................ 109 AdvanceT rac .............................. 224 Air cleaner filter ....... 301–302, 304 Air conditioning ....................87, 89 Airbag supplemental restraint system ................174–175, 179, 181 and child safety seats .
plastic parts ............................ 270 washing .................................... 268 waxing ..................................... 269 wheels ...................................... 269 wiper blades ............................ 271 Climate control (see Air conditioning or Heating) .
Exhaust fumes .......................... 220 F Fail safe cooling ........................ 289 Floor mats .................................137 Fluid capacities ......................... 304 Foglamps ..................................... 97 Fuel .......
J Jack ............................................ 248 positioning ............................... 248 storage ..................................... 248 Jump-starting your vehicle ......254 K Keyless entry system ............... 148 autolock ........
Power adjustable foot pedals ...113 Power distribution box (see Fuses) ....................... 243, 246 Power door locks ...................... 138 Power mirrors ........................... 112 Power steering .................. 226–227 fluid, checking and adding .
T ires ........................... 197–198, 248 alignment ................................ 204 care .......................................... 201 changing .......................... 248, 251 checking the pressure ............ 201 inflating ........
320.
An important point after buying a device Lincoln LS (2006) (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Lincoln LS (2006) yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Lincoln LS (2006) - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Lincoln LS (2006) you will learn all the available features of the product, as well as information on its operation. The information that you get Lincoln LS (2006) will certainly help you make a decision on the purchase.
If you already are a holder of Lincoln LS (2006), but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Lincoln LS (2006).
However, one of the most important roles played by the user manual is to help in solving problems with Lincoln LS (2006). Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Lincoln LS (2006) along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
