Instruction/ maintenance manual of the product Smith Machine Life Fitness
Go to page of 12
Signature Smith Machine Owners Manual.
Signature Smith Machine Safety & W arranty Purchasers of LIFE FITNESS products should read the Owner's Manual and all of the warning labels on the products before using them.
.
Signature Smith Machine Safety & W arranty LIMITED WARRANTY WHAT IS COVERED This Life Fitness commercial exercise equipment (Signature Benches and Racks) is warranted to be free of all defects in .
HOW TO GET PARTS & SERVICE Simply call Customer Support Services at (800) 351-3737 or (847) 451-0036, Monday through Friday from 8:00 a.m. to 6:00 p.
Signature Smith Machine Safety & W arranty 1. Frame Construction: Frame is constructed of mechanical quality steel purchased in mill run quantities. Frame is primarily 2 1/2" x 4 1/2" oval shaped tubing and 5 1/4” x 3 3/4” “D” shaped tubing with 11 gauge wall thickness.
Item Qty Description P art Number 1 1 Left Side F rame 82942xx (Ref) 2 1 Right Side F rame 82943xx (Ref) 3 1 Back Brace 82949xx (Ref) 4 10 M10 X 130mm Bolt 3236220 5 22 3/8" W asher 3236601 6 10 1/4" Spacer (.
Signature Smith Machine Assembly Instructions BE SURE TO SELECT A LEVEL LOCATION FOR ASSEMBLY. THE SIGNATURE SMITH MACHINE MUST REST LEVEL AND IN COMPLETE CONTACT WITH THE FLOOR. 1. With the help of another person, erect the LEFT and RIGHT SIDE FRAMES (1 & 2).
14 12 15 12 14 4. Insert two LINEAR BEARINGS (12) into the ends of the RIGHT CARRIAGE (15), secure the LINEAR BEARINGS with one SNAP RING (14) at each bearing. NOTE: Leave the cardboard sleeve in the bottom LINEAR BEARING, remove the cardboard sleeve from top bearing.
6. Loosen the four set screws on the pre-assembled 1.25" SHAFT COLLARS (C) located at the top of the SIDE FRAMES. 7. With the help of another person and the LIFT BAR ASSEMBLY (D) oriented as shown, position it near the bottom of the GUIDE RODS (E).
When all of the above criteria have been met, tighten the JAM NUT (18) and continue to complete the installation. 15. Install 1" HOLE PLUGS (9) into all open bolt holes.
Signature Smith Machine Maintenance ONCE A WEEK O Visually inspect all hardware, including jam nuts, for loosening, tampering or wear. O Check condition of hand grips. ONCE A MONTH O Inspect hardware and tighten any bolts or nuts that may have loosened during use.
An important point after buying a device Life Fitness Smith Machine (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Life Fitness Smith Machine yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Life Fitness Smith Machine - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Life Fitness Smith Machine you will learn all the available features of the product, as well as information on its operation. The information that you get Life Fitness Smith Machine will certainly help you make a decision on the purchase.
If you already are a holder of Life Fitness Smith Machine, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Life Fitness Smith Machine.
However, one of the most important roles played by the user manual is to help in solving problems with Life Fitness Smith Machine. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Life Fitness Smith Machine along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
