Instruction/ maintenance manual of the product Fit-1 Life Fitness
Go to page of 26
FIT SERIES FIT -1 Part # 7317701 Rev B. Revision:8/30/02 1 ASSEMBLY INSTRUCTIONS.
PARTS LIST PA R T # 04-1325 04-1326 04-1327 04-1328 04-1330 04-1335 04-1329 04-1334 04-1331 04-1338 04-1336 04-1337 04-1332B 04-1339B 04-1333 04-1340 02-1294 01-2073 01-2008 02-1292 02-1296 02-1295 10.
3 60 3/8 X 1” (25m) BOL T 61 3/8 X 1-1/4” (32m) BOL T 62 3/8 X 1-3/4” (43m) BOL T 64 3/8 X 2-1/2” (67m) BOL T 68 3/8 X 2-3/4” (70m) BOL T 63 3/8 X 3-1/2” (90m) BOL T 53 3/8 X 4” (97m) BO.
4 67 3/8 X 4-1/4” (106m) BOL T 69 3/8 X 6-1/2” (164m) BOL T 72 3/8 X 3” (76m) BUTTON HEAD BOL T 57 1/2 X 3” SHOULDER BOL T 55 1” FLANGE SP ACER 71 3/8 X 1” (25m) BUTTON HEAD BOL T 54 1/2.
STEP 1: FIGURE 1 5 • LOOSEL Y assemble the REAR UPRIGHT (5) to the BASE (1) to the using four RH CAPS (78), two 3/8 X 3-1/2” BOL TS (63), four 3/8” SAE W ASHERS (75), four 3/8” RH W ASHERS (76) and two 3/8” LOW HEIGHT LOCK NUTS (73) as shown in FIGURE 1.
STEP 2: FIGURE 2 6 • LOOSEL Y assemble the LEFT and RIGHT BOOM SUPPOR TS (3 & 4) to the REAR UPRIGHT (5) using four RH CAPS (78), two 3/8 X 3” BOL TS (65), four 3/8” SAE W ASHERS (75), four 3/8” RH W ASHERS (76) and two 3/8” LOW HEIGHT LOCK NUTS (73) as shown in FIGURE 2.
FIGURE 3 7 STEP 3: FIGURE 4 STEP 4: • SECUREL Y assemble one STORAGE PEG (25) to the LEFT BOOM SUPPOR T (3) using one RH CAPS (78), one 3/8 X 1” BOL T (60), one 3/8” SAE W ASHER (75) and one 3/8” RH W ASHER (76) as shown in FIGURE 3.
STEP 6: FIGURE 6 8 STEP 5: FIGURE 5 2 12 • Pull back on the SPRING PIN and slide the ADJUST ABLE SEA T (12) over the BENCH FRAME (2) as shown in FIGURE 5.
9 STEP 7: TIGHTEN! • Securely tighten all loose frame connections made to this point, then proceed to snap RH CAPS (78) over the RH W ASHERS (76) on all tightened connections.
STEP 9: FIGURE 9 10 STEP 8: FIGURE 8 51 18 7 76 78 73 75 3/8 X 4-1/4” (106m) 67 2 7 • Insert one 3-5/16” PIVOT SHAFT (47) into the PEDEST AL (7) as shown in FIGURE 8.
STEP 1 1: FIGURE 1 1 11 STEP 10: FIGURE 10 46 6 15 76 BLACK 77 73 75 3/8 X 4-1/4” (106m) 67 12 11 • SECUREL Y assemble the SEA T SUPPOR T (11) to the ADJUST ABLE SEA T (12) using two BLACK RH CAPS.
STEP 13: FIGURE 13 12 STEP 12: FIGURE 12 77 BLACK 76 3/8 X 1-1/4” (32m) 61 11 42 76 BLACK 77 73 75 12 • SECUREL Y assemble the BACK P AD SUPPOR T (15) to the ADJUST ABLE SEA T (12) using two BLACK.
STEP 14: FIGURE 14 13 BLACK 77 75 3/8 X 3” (73m) 65 15 43 • SECUREL Y assemble the BACK P AD (43) to the BACK P AD SUPPOR T (15) using two BLACK RH CAPS (77), two 3/8 X 3” BOL TS (65), two 3/8” SAE W ASHERS (75) and two 3/8” RH W ASHERS (76) as shown in FIGURE 14.
STEP 17: FIGURE 17 14 STEP 16: FIGURE 16 14 1/2 X 3” 57 73 13 76 78 73 75 13 1 53 3/8 X 4” (97m) • SECUREL Y assemble the SWIVEL SUPPOR T (13) to the BASE (1) using four RH CAPS (78), two 3/8 X 4” BOL TS (53), four 3/ 8” SAE W ASHERS (75), four 3/8” RH W ASHERS (76) and two 3/8” LOW HEIGHT LOCK NUTS (73) as shown in FIGURE 16.
15 STEP 18: FIGURE18 9 36 37 • Slide two 5” ACCORIDIAN SLEEVES (36) over the shafts on the PIVOT ARM (9) as shown in FIGURE 18. • Slide two PILLOW BLOCKS (37) over the shafts on the PIVOT ARM (9) as shown in FIGURE 18.
16 STEP 20: FIGURE 20 • Insert one 5-1/2” T APPED PIVOT SHAFT (41) into the PIVOT ARM (9). • SECUREL Y assemble the PRESS ADJUST PLA TE (26) to the PIVOT ARM (9) using three BLACK RH CAPS (77),t.
STEP 24: FIGURE 24 17 • Insert two GUIDE RODS (27) through the BOTTOM SHROUD BRACKET (20) and into the BASE (1) as shown on FIGURE 24. • Slide two 3/4 X 2” WEIGHT ST ACK CUSHIONS (30) down over the GUIDE RODS (27) as shown in FIGURE 24.
STEP 25: FIGURE 25 18 • CAREFULL Y assemble the ST ACK BOOM (8) over the GUIDE RODS (27) as shown in FIGURE 25. 27 8 STEP 26: FIGURE 26 • LOOSEL Y assemble the ST ACK BOOM (8) to the REAR UPRIGHT .
19 FIGURE 27 STEP 27: 64 3/8 X 2-1/2” (67m) 8 50 38 FIGURE 28 STEP 28: 73 78 62 3/8 X 1-3/4” (43m) 21 76 75 • Slide the two 13/16” SHAFT COLLARS (50) to the top of the ST ACK BOOM (8) and SECUREL Y tighten the SHAFT COLLAR (50) set screws. • Route the LA T CABLE (44) through the REAR UPRIGHT (5).
FIGURE 29 20 STEP 29: • SECUREL Y assemble two 4-1/2” PULLEYS (38) to the BOOM (8) using two BLACK RH CAPS (77), two RH CAPS (78), two 3/8 X 2-3/4” BOL TS (68), four 3/8” SAE W ASHERS (75), fo.
21 FIGURE 30 STEP 30: • Route the LEG CABLE (45) through the SWIVEL (14) and assemble two 4-1/2” PULLEYS (38) to the SWIVEL (14) using four BLACK RH CAPS (77), two 3/8 X 1-3/4” BOL TS (62), four 3/8” SAE W ASHERS (75), four 3/8” RH W ASHERS (76) and two 3/8” LOW HEIGHT LOCK NUTS (73) as shown in FIGURE 30.
22 FIGURE 32 STEP 32: 73 78 62 3/8 X 1-3/4” (43m) 38 76 75 • Route the LEG CABLE (45) around one 4-1/2” PULLEY (38) and assemble the PULLEY (38) to the lower holes of the two DUAL PULLEY PLA TES.
23 FIGURE 33 STEP 33: 45 78 76 38 73 62 • Route the LEG CABLE (45) through the bracket on the BASE (1) and assemble one 4-1/2” PULLEY (38) to the bracket on the BASE (1) using four RH CAPS (78), t.
STEP 34: FIGURE 34 24 • Assemble the LOW ROW BAR (34) to the LEG CABLE (45) using two SNAP LINKS (40) and one 12-LINK CHAIN (48) as shown in FIGURE 34. • Assemble the LA T BAR (28) to the LA T CABLE(44) using one SNAP LINK (40) as shown in FIGURE 34.
STEP 35: FIGURE 35 25 • Adjustments can be made in the above locations to set the correct amount of tension in the cables. • If upon completion of assembly , the HEAD PLA TE (29) does not sit on top of the first WEIGHT PLA TE (31), push the HEAD PLA TE (29) down, insert the WEIGHT ST ACK PIN (33) and perform several repetitions.
Clean: • Upholstery with mild soap and water . • Guide rods with a cotton cloth. • Hand grips with mild soap and water . • Frame damage can be repaired with touch-up paint can be purchased fro.
An important point after buying a device Life Fitness Fit-1 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Life Fitness Fit-1 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Life Fitness Fit-1 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Life Fitness Fit-1 you will learn all the available features of the product, as well as information on its operation. The information that you get Life Fitness Fit-1 will certainly help you make a decision on the purchase.
If you already are a holder of Life Fitness Fit-1, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Life Fitness Fit-1.
However, one of the most important roles played by the user manual is to help in solving problems with Life Fitness Fit-1. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Life Fitness Fit-1 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
