Instruction/ maintenance manual of the product 8215 Life Fitness
Go to page of 21
8215 MULTI-PRES S Part # 6875601 Revision:3/17/00 1 ASSEMB L Y INSTRUCTIONS.
IMPORTANT NOTES Please note: Tools Required for Assembly * Thank you for purchasing the LIFE FITNESS 8215 MULTI-PRESS. Please read these instruc- tions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function.
3 PARTS LIST PART # 6795203 6784303 6755602 6755903 6878202 6783403 6781303 6784703 6784103 6624302 6624203 6651602 6780304 6780004 6791102 6214501 6284501 6714601 3116101 6782301 6784601 6382301 3108.
4 STEP 1: FIGURE 1 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • LOOSELY assemble LOWER SUPPORT (6) to the TOWER (1) and PRESS FRAME (2) using four 1/2 X 4 ” BOLTS (31), four 1/2 ” WASHERS (41), and three 1/2 ” LOCK NUTS (43).
STEP 2: FIGURE 2 5 • SECURE LY assemble one 3/8 ” SPRING PIN (48) to the WOLFF SLEEVE (3) as shown in FIGURE 2. (IMPORTANT! Tighten nut of SPRING PIN completely.) • Attach one U-PIN (50) to the WOLFF SLEEVE (3) using one 1/2 ” P AL NUT (24). Slide one 4 ” VINYL CAP (25) onto the U-PIN (50) as shown in FIGURE 2.
STEP 3: FIGURE 3 6 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • SECURE LY assemble the PRESS FRAME (9) to the PRESS BASE (2) using one 1/2 X 3 ” BOLT (32), two 1/2” WASHERS (41), and one 1/2 ” LOCK .
7 STEP 4: FIGURE 4 • Slide two HINGE TABS (46) onto the WOLFF SLEEVE (3) and SECUREL Y assemble SE AT PAD (14) using two 3/8 X 1-1/4 ” BO LTS (39), and two 3/8 ” W ASHERS (42).
STEP 5: 8 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • Slide the RIGHT BACK PAD ANGLE (10) and the LEFT BACK PAD ANGLE (11) onto the shaft on the WOLFF SLEEVE (3) as shown in FIGURE 5.
FIGURE 6 9 • SECURELY assemble the BACK PAD (13) to the LEFT & RIGHT BACK PAD ANGLES (11 & 10) using four 3/8 X 1-1/4 ” BO LTS (39) and four 3/8 ” W ASHERS (42).
FIGURE 7 10 • Slide two PILLOW BLOCKS (27) over the shaft on the PRESS ARM ADJUST (5) and SECURELY assemble the two PILLOW BLOCKS (27) to the UPPER SUPPORT (8) using four 3/8 X 3-1/4 ” BOLTS (35), four 3/8 ” WASHERS (42), and four 3/8 ” LOCK NUTS (45) as shown in FIGURE 7.
FIGURE 8 11 • SECURELY assemble one 1/2 ” SPRING PIN (47) to the PRESS ARM (4) as shown in FIGURE 8. (IMPORTANT! Tighten spring pin completely.) STEP 8: 29 1/2 X 7-1/2 ” 4 5 44 1/2 ” LOW HEIGH.
12 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 9 STEP 9: • Snap two WEIGHT PLATE BUSHINGS (22) into the top side of all twenty WEIGHT PLATES (16) as shown in FIGURE 9.
FIGURE 10 13 • Insert the two GUIDE RODS (20) into the base of the TOWER (1) as shown in FIGURE 10. Lubricate the GUIDE RODS with a slicon or teflon spray that is available at most hardware stores. • Slide two WEIGHT STACK CUSHIONS (23) down over the GUIDE RODS (20).
14 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 11 FIGURE 12 STEP 11: • SECURELY assemble two 4-1/2 ” PULLEYS (19) to the TOWER BRACE (7) using two 3/8 X 2 ” BOLTS (38), and two 3/8 ” LOCK NUTS (45).
FIGURE 13 15 STEP 13: • Wrap the CABLE (21) around one 4-1/2 ” PULLEY (19) and SECURELY assemble the pulley to the REAR slot of the PRESS ARM ADJUST (5) using one 3/8 X 2-3/4 ” BO LT (37), two 3/8 ” FLANGE SPACERS (52), and one 3/8 ” LOCK NUT (45) as shown in FIGURE 13.
FIGURE 14 16 STEP 14: 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • Route the threaded end of the CABLE (21) through the large hole in the PRESS FRAME (9) as shown in FIGURE 14.
FIGURE 15 17 STEP 15: • Wrap the CABLE (21) around one 4-1/2 ” PULLEY (19) and SECURELY assemble the 4-1/2 ” PULLEY (19) to the horizontal pulley bracket on the PRESS FRAME (2) using one 3/8 X 2 ” BOLT (38), one 2-7/8 ” CABLE CLIP (26), and one 3/8 ” LOCK NUT (45) as shown in FIGURE 15.
FIGURE 16 18 STEP 16: 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • Wrap the CABLE (21) around one 4-1/2 ” PULLEY (19) and SECURE LY assemble the 4-1/2 ” PULLEY (19) to the vertical pulley bracket on the LOWER SUPPORT (6) using two 3/8 X 2 ” BO LTS (38) and two 3/8 ” LOCK NUTS (45) as shown in FIGURE 16.
19 FIGURE 17 STEP 17: • Screw the treaded end of the CABLE (21) approximately 3/4 ” into the end of the WEIGHT STACK SHAFT (17) and tighten jam nut securely.
STEP 18: • Slide the SHROUD (15) between the TOWER (1) as shown in FIGURE 18. FIGURE 18 20 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 15 1.
21 FIGURE 19 STEP 19: 1 15 Thank you for purchasing the LifeFitness 8215 MU LTI-PRESS. If unsure of proper use of equipment, call your local LifeFitness distributor or call the LifeFitness customer service department at (800) 328-9714.
An important point after buying a device Life Fitness 8215 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Life Fitness 8215 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Life Fitness 8215 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Life Fitness 8215 you will learn all the available features of the product, as well as information on its operation. The information that you get Life Fitness 8215 will certainly help you make a decision on the purchase.
If you already are a holder of Life Fitness 8215, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Life Fitness 8215.
However, one of the most important roles played by the user manual is to help in solving problems with Life Fitness 8215. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Life Fitness 8215 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
