Instruction/ maintenance manual of the product 663 Life Fitness
Go to page of 19
1 663 660 SECOND ST ACK OPTION CLASS H PAR T # 7050101 REV . C Revision: 07/31/01 USER’S GUIDE W ARNING: Read and follow all directions for each step to insure proper assembly of this product.
THERE IS A RISK ASSU MED BY IND IVIDUALS W HO USE T HI S TYPE OF EQUIPMENT. TO MINIMIZE RISK F OLLOW THESE RULE S ! 1. Before u sing, read al l the w arnings and in structions on the use of this mach ine. Use only for in tended exercise. DO NOT mo dify the m achine.
IMPOR T ANT NOTES Please note: T ools Required for Assembly * Thank you for purchasing the ParaBody 663 660 Second Stack Option. Please read these instructions thoroughly and keep them for future reference. 3 NOTE: BOL T LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOL T .
STEP 2 FIGURE 2 FIGURE 1 STEP 1 • REMOVE the four 3/8” X 1” BUTTON HEAD CAP SCREWS from the top of the front SHROUD & rear SHROUD. See FIGURE 1.
STEP 3 FIGURE 3 5 • Unscrew the threaded ends of the HEAD PLA TE CABLE from the WEIGHT ST ACK SHAFT & the D-RING and remove HEAD PLA TE CABLE. The HEAD PLA TE CABLE will be used later .
6 PRESS CABLE (67249) STEP 4 • Remove the PRESS CABLE (67249) from the KEYHOLE CLEVIS and ELASTIC CORD. (NOTE: The LA T or LEG EXT CABLE can be moved over one hole on the D-RING so the KEYHOLE CLEVIS are evenly spaced .) FIGURE 4 ELASTIC CORD D-RING KEYHOLE CLEVIS • Discard the KEYHOLE CLEVIS and ELASTIC CORD.
7 STEP 6 FIGURE 6 • Assemble the previously removed 2” PULLEY to the bracket on the TOP BOOM using one 3/8 X 1” BOL T (1 1), one previously remov ed 3/8” W ASHER, and one previously removed 3/8” LOCK NUT . See FIGURE 6. • (NOTE: STEP 6 is only completed if the 100101 LEG PRESS OPTION is installed otherwise proceed to STEP 7.
FIGURE 8 STEP 8 • Discard the two 3/8 X 1/2” SP ACERS. • Remove two 2” PULLEYS to the rear bracket on the T OP BOOM using one 3/8” THREADED SHAFT , two 3/8” W ASHERS, two 3/8” HEX NUTS, and two 3/8” LOCK NUTS as shown in FIGURE 8. FIGURE 9 STEP 9 • Position the elastic cords over the 2” PULLEYS as shown in FIGURE 9.
STEP 10 • Carefully remove and discard the PRESS CABLE as shown in FIGURE 10. PRESS CABLE (67249) FIGURE 10 9 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2.
10 STEP 1 1 • Route the new PRESS-ST ACK CABLE (5) around the pulleys and l-brackets as shown in STEP 11. (Remove pulleys for ease of installation.) 5 5 FIGURE 1 1 FIGURE 12 STEP 12 PRESS-ST ACK CAB.
FIGURE 14 STEP 14 • LOOSEN the bolts holding the TOP BOOM to the UPRIGHTS. Bolts will have to be removed to install GUIDE RODS (1). See FIGURE 14. 11 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 LOOSEN! TOP BOOM LOOSEN! STEP 13 • Snap two WEIGHT PLA TE BUSHINGS (17) each, into the “ top” side of fifteen WEIGHT PLA TES (16) as shown in FIGURE 13.
FIGURE 15 STEP 15 • Insert two GUIDE RODS (1) into the BASE as shown on FIGURE 15. (NOTE: Lubricate GUIDE RODS (1) with silicon or teflon spray available at most hardware stores.) • Slide two WEIGHT ST ACK SP ACERS (3), two 3/4” W ASHERS (15), and two WEIGHT ST ACK CUSHIONS (8) - IN THA T ORDER - down over the GUIDE RODS (1).
STEP 16 FIGURE 16 13 • W ith the GUIDE RODS (1) securely held in the T OP BOOM. Tighten all TOP BOOM connections. (NOTE: Make sur e the LA T CABLE runs over the top of the bolts in the TOP BOOM.) 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 TIGHTEN! ( NOTE: Make sure LA T CABLE runs over top of bolts in TOP BOOM.
14 HEAD PLA TE CABLE (7041801) STEP 17 FIGURE 17 • Screw one of the threaded ends of the previously removed HEAD PLA TE CABLE approximately 1” into the end of the WEIGHT ST ACK SHAFT . See FIGURE 17. WEIGHT ST ACK SHAFT STEP 18 • Screw the other threaded end of the HEAD PLA TE CABLE approximately 1” into the end of the shaft on the D-RING.
STEP 19 FIGURE 19 15 REAR SHROUD • The rear SHROUD opening must be removed. Apply pressure to the bottom of the SHROUD where the “V” groove is and carefuly remove the weight stack opening on the plastic SHROUD as shown in FIGURE 19.
STEP 21 FIGURE 21 FIGURE 20 STEP 20 • SECUREL Y attach the four previously removed 3/8” X 1” BUTTON HEAD CAP SCREWS from the top of the front SHROUD & rear SHROUD.
MAINTENANCE MODEL #________________________ SERIAL #_________________________ DA TE OF PURCHASE: _____________ DEALERS NAME: _________________ DEALERS PHONE #_______________ 17 * W e recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water .
18 NOTES: LIMITED W ARRANTY ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The W arranty terms apply to IN HOME USE ONL Y . 1. LIMITED W ARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repair ed or replaced by ParaBody .
INTERNA TIONAL OFFICES LifeFitnessAtlantic BV Atlantic Headquarters Bijdorpplein 25-31 2992 LB Barendrecht The Netherlands Phone: (180) 646 666 Fax: (180) 646 703 LifeFitness Japan 8/F , Nippon Brunswick Building 5-27-7 Sendagaya Shibuya-Ku, T okyo 151-0051 Japan Phone: 81 (3) 3359-4309 Fax: 81 (3) 3359-4307 LifeFitness (UK) Ltd.
An important point after buying a device Life Fitness 663 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Life Fitness 663 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Life Fitness 663 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Life Fitness 663 you will learn all the available features of the product, as well as information on its operation. The information that you get Life Fitness 663 will certainly help you make a decision on the purchase.
If you already are a holder of Life Fitness 663, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Life Fitness 663.
However, one of the most important roles played by the user manual is to help in solving problems with Life Fitness 663. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Life Fitness 663 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
