Instruction/ maintenance manual of the product XDA Liebert
Go to page of 16
Precision Cooling For Bu siness-Critical Con tinuit y Lieber t XDA ™ Air Flow Enhan c er User Manua l.
.
i TABLE OF CONTENTS 1.0 Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 Features & Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.0 Installation . . . . . . . . . . . . . . . . .
ii.
1 1.0 P RODUCT D ESCRIPTION The Liebert XDA Air Flow E nhancer increases the airflow through densely populated enclosures, breaki ng up hot spots within the enclo- sure that can threaten the uptime of your critical systems.
2 2.0 I NST ALLATION The Liebert XDA can be attached to most equi pment cabinet doors 60" tall or taller. The unit typical ly is installed on the outside of a cabi- net’s rear door, generally used to discharge heat generated from the cabinet.
3 2.2.1 Required T ools • Phillips screwdriver • Pliers • Scissors 2.3 Mounting the XDA on the Exterior of the Rear Cabinet Door 2.3.1 P rep are to Ins t all the Un it 1. Determine the desired mount- ing position on the door. 2. Attach the mounting bracket to the top of the XDA, positioning the bracket to obtain the desired mounting height.
4 2.3.2 Mount the Unit and Att ach it to the Cabinet 1. Lift the unit with bracket attach ed and h ang it on the door, as shown at right. Ensure that the bracket rests safely on top of the top edge of door. 2. Move the unit sideways into the desired position.
5 2.4 Mounting the XDA on the Interior of the Rear Cabinet Door 2.4.1 P rep are to Ins t all the Un it 1. Remove the s crews on the sides of the XDA that secure the mounting angles to the unit. 2. Remove the mounting angles. 3. Position the angles so their mounting surfaces are near the fron t of the XDA .
6 2.4.2 Mount the Unit and Att ach It to the Cabinet 1. Lift the unit onto the door, plac ing the two mounting holes on the top end, over the two screws atta ched to the door and bracket.
7 3.0 P OWER C ONNECTIONS Connect the power cords to separate power sources (as specified in Specifications on page 9 ), to keep the XDA operating if there is a power failure on one circuit. Route the power cords under or over the cabinet as needed to the ne arest av ailable receptacles.
8 4.0 O PERATION & M AINTENANCE The XDA is activated by turning on the ON/OFF switch on the bottom of the unit, near the power cords. All fans operate continuously to remove the maximum amount of heat from the cab- inet.
9 5.0 S PECIFICATIONS Nominal Capacity 1000 CFM @ 60Hz Dimensions W x D x H, in (mm) 8 x 2.25 x 56 (203.2 x 57.2 x 1422.4) Wei ght, lbs (kg) 25 (1 1.3) Electrical S pecifications 120V -1-50/60Hz 230V -1-50/60Hz Amp Draw 1.
10.
.
Ensuring The High A v ailab ilit y 0f Mission-Critic al Dat a And Applic a tions. While every precaution has been tak en to ensure the accuracy and complete ness of this literature , Liebert Corporation assumes no responsibility and disclaims all liability for damages resulting from u se of this informa tion or for any errors or omissions .
An important point after buying a device Liebert XDA (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Liebert XDA yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Liebert XDA - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Liebert XDA you will learn all the available features of the product, as well as information on its operation. The information that you get Liebert XDA will certainly help you make a decision on the purchase.
If you already are a holder of Liebert XDA, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Liebert XDA.
However, one of the most important roles played by the user manual is to help in solving problems with Liebert XDA. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Liebert XDA along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
