Instruction/ maintenance manual of the product 4300 ABC Office
Go to page of 12
OPER AT ING INSTRUCTIONS FINISHER 4300 Model No. BA-FS43 Banner American Products, Inc. abcoffice 800-658-8788 www.abcoffice.com.
Table of Contents I. For Your Safety ............................................... 2 II. Electrical Safeguards ....................................... 2-3 III. Specifications .................................................. 3 IV. Set-up ..........
Finisher 4300 (BA-FS43) SPEED CONTROL TOP BOTTOM TEMPERATURE CONTROL BOTTOM HEAT SHOE TEMPERATURE CONTROL TOP HEAT SHOE 1 0 1 0 FORWARD REVERSE FANS MOTOR HEAT HEATED ROLLERS Control Panel Brake Nut C.
u Do not connect the laminator to electrical power or attempt to operate it until you have read these instructions completely. Keep these instructions in a convenient location for future reference. u Read all safety messages located in this instruction manual and on the laminator very care- fully.
u Do not operate the laminator with a damaged power supply cord or plug. u Replace fuses only with same type rated 30A, 240V and 1A, 250V fuses. Contact your dealer for replacement fuses. u There are four (4) EMERGENCY STOP buttons on your Finisher 4300, two in the front and two in the back.
Threading the Film (Figures 1&2) 1. Feed the film from the top roll behind the upper idler roller rod and lay it over both heat shoes. Be sure that the adhesive side of the film is facing out and the non-adhesive side is against the heat shoes. 2.
Slitters (Figure 4) : To install the slitters, place the Main Body Clamps into the Top Roller Guard where they will slide into the slots in the in the top edge of the guard located at each end of the guard. Before setting the slitters in place, ensure the machine is loaded with the proper laminating film.
VI. Pressure Sensitive Laminating... Note: You must have the Rewind Option for Pressure Sensitive Films in order to laminate with pressure sensitive material. 1. Load a roll of pressure sensitive film onto the upper mandrel so that it unwinds toward you from the bottom of the roll.
VIII. Mounting & Laminating... 1. Be sure all laminator parts (i.e. safety shield, feed table, etc.) are in their proper positions and the laminat- ing film is loaded correctly (See page 3 for film loading instructions). 2. Open the ROLLER RELEASE handle and select the MOUNT position on both sides of your laminator.
Cleaning Rubber Rollers: Excessive build-up of adhesive on the rollers may cause poor lamination quality and erratic film movement. Use the following procedure to remove any adhesive from the laminating rollers. 1. Turn the HEATED ROLLERS and TOP & BOTTOM SHOES OFF and allow the laminator to cool .
X. Trouble-shooting... Symptom Possible Cause Corrective Action LCDs do not show display No power to laminator Close panel breaker when heat switches are on. Blown fuse Disconnect power and replace fuse Film is not bonding to the print Laminator not set to optimal Adjust temperature slightly laminating temperature upward.
XI. Laminating & Mounting Do’s and Don’ts... Read the instruction manual before operating your laminator. Always run test samples before laminating valuable items. Feed the print through slowly and evenly, smoothing it as it is pulled into the laminator.
An important point after buying a device ABC Office 4300 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought ABC Office 4300 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data ABC Office 4300 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, ABC Office 4300 you will learn all the available features of the product, as well as information on its operation. The information that you get ABC Office 4300 will certainly help you make a decision on the purchase.
If you already are a holder of ABC Office 4300, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime ABC Office 4300.
However, one of the most important roles played by the user manual is to help in solving problems with ABC Office 4300. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device ABC Office 4300 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
