Instruction/ maintenance manual of the product 073-0711 Apple
Go to page of 13
073-0711 Re v . B Xserve Logic Board with Processor/Heatsink Replacement Instructions F ollow the instructions in this sheet carefully . F ailure to f ollo w these instructions could damage your equipment and v oid its w arranty . Note: Online instructions cov ering customer-installable par ts are av ailab le at http://www .
Xserve Logic Board with Processor/Heatsink - 2 3. If the ser v er is in the loc k ed position (the y ellow security LED on the front panel is on), use the Allen ke y that came with the server to unloc k it. 4. If the cable management arm is not in use, unplug all e xternal cables e xcept the power cord.
Xserve Logic Board with Processor/Heatsink - 3 8. Grasp the thumbscre ws and slide the bottom housing f orward part wa y to e xpose the two chassis le v ers . (Figure 2) 9. While depressing both le v ers , pull the bottom housing all the w a y forward and remo v e it from the rac k.
Xserve Logic Board with Processor/Heatsink - 4 Removing the Installed Logic Board Note: The replacement logic board does not include memor y DIMMs or expansion cards .
Xserve Logic Board with Processor/Heatsink - 5 Dual-Slot Riser 1. Release the thumb screw that secures the card to the bac k of the server . (Figure 4) 2. Disconnect the riser from the logic board and remove the riser from the server . Figure 4 Single-Slot Riser 1.
Xserve Logic Board with Processor/Heatsink - 6 2. Pull the clip on the riser forw ard to release the riser from the logic board connector . (Figure 6) 3. Disconnect the riser from the logic board and remov e the riser and card from the ser v er . Figure 6 Heatsink Duct 1.
Xserve Logic Board with Processor/Heatsink - 7 A T A Controller Board 1. Disconnect the blo wer cab le nearest the A T A controller board. (Figure 8) 2. Press in on both ends of the clip securing the r ight side of the A T A controller board and remov e the clip from the server .
Xserve Logic Board with Processor/Heatsink - 8 Po wer Supply 1. Release the locking latch on the po wer supply cab le connector and disconnect the cable from the driv e interconnect board. (Figure 9) 2. Release the thumbscrew that secures the po wer supply to the chassis .
Xserve Logic Board with Processor/Heatsink - 9 Logic Board 1. Release the thumb screw that secures the logic board to the chassis . (Figure 10) 2. Mov e the logic board f orw ard and up slightly to release it from the f our mounting pegs. 3. Tilt up the end of the logic board nearest the blo wers so that the board ports clear the chassis.
Xserve Logic Board with Processor/Heatsink - 10 2. Install the replacement logic board in the bottom housing, making sure the board fits ov er the f our mounting pegs on the chassis floor . W arning: When replacing the logic board, make sure the por ts and the identifier button on the bac k of the boar d align with the openings in the chassis.
Xserve Logic Board with Processor/Heatsink - 11 8. Reinstall the two A T A controller clips. Note: When replacing the ATA controller board clips, orient them so that the long end of each clip points away from the middle of the server. Place the inside edge of the clip into the small notch and then snap down the outer edge of the clip.
Xserve Logic Board with Processor/Heatsink - 12 12. Remov e the battery insulator tab from the batter y holder on the replacement logic board. (Figure 14) Figure 14 Note: Replacing the logic board in the ser v er changes its Ethernet ID number . The new number is printed on an Ether net ID label pac kaged with the replacement logic board.
Xserve Logic Board with Processor/Heatsink - 13 Apple Computer , Inc. © 2002 Apple Computer , Inc. All rights reser v ed. This document is protected under U .S . Copyright La w and International T reaties, and no par t of this document ma y be reproduced in any f orm without written per mission from Apple.
An important point after buying a device Apple 073-0711 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Apple 073-0711 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Apple 073-0711 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Apple 073-0711 you will learn all the available features of the product, as well as information on its operation. The information that you get Apple 073-0711 will certainly help you make a decision on the purchase.
If you already are a holder of Apple 073-0711, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Apple 073-0711.
However, one of the most important roles played by the user manual is to help in solving problems with Apple 073-0711. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Apple 073-0711 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
