Instruction/ maintenance manual of the product FSW-0800FXT LevelOne
Go to page of 14
LevelOne FSW -0800FXC FSW -0800FXT FSW -1600FXC FSW -1600FXT 8/16 Port 100Mbps Fast Ethernet Switch with SC/ST Connector User ’ s Guide.
Caution Circuit devices are sensitiv e to static electricity, w hich can damage their delicate electronics. Dry w eather conditions or wa lking across a carpeted floor may cause you to acquire a static electrical charge.
Contents Cauti on .............................................................................................................. I Electronic Emissi on Notice s ............................................................................... I Chapter 1 Introduction .
1- 1 Chapter 1 Introduction Overview The Levelone 8/16 Port Fiber Switch is a standard switch that meets all IEEE 802.3u/802.3x specifications. Fast Ethernet Switch is a cost-effective solution for easing your network congestion problem on existing shared-hub network by breaking up the collision domain and by multiplying the network performance.
2- 1 Chapter 2 Installing & Network Connection Installation Þ The fiber TX, RX cables must be paired at both ends. Þ Repeat the above step, as needed, for each fiber port to be connected to a 100Base-FX device. Þ The fiber port can be up-linked to an upper level hub's port.
3-1 Chapter 3 Troubleshooting Network troubleshooting req uires patie nce and log ic. Generally speaking, t he cabling and workstation c onfigur ations are the likely first suspects; network hardware is usually last on the list. The natur e of the hub design dict ates that it is more likely for an entire hub to fail instead of just a single port.
A-1 16 Port Fiber Switch Technical Specifications Standards Compliance : IEEE802.3u and 802.3x 100Base-FX Transmission Mode : Full or Half duplex Transmission Speed : 100Mbps Packet forwarding/filteri.
A-2 8 Port Fiber Switch Technical Specifications Standards Compliance : IEEE802.3u and 802.3x 100Base-FX Transmission Mode : Full or Half duplex Transmission Speed : 100Mbps Packet forwarding/filterin.
3-2 Workstation Problems Most non-cabling problems result from improper config urat ion of the net work interface card (NIC) and its corresponding driver. The following point s will be helpful: • Like other ad d-on cards in the w orkstation or server, N IC must have unique memory address, I/O address, and interrup t.
2- 2 For connection to Router, Bridge, or regular 100Base-X Hub, please refer to the device’s Technical Manual for respective bit-time delay. Switch Hub Cascading and Long-Haul Connection Theoretically, the switch hub breaks up the collision domain in hub cascading that you may up-link the hubs unlimitedly.
2- 3 Every fiber port is FDX/HDX selectable by DIP switches, the default setting is FDX. You may force each fiber port into either FDX or HDX. Two typical modes between local and remote fiber devices .
2- 4 mode setting. Then, power on to restart the new configuration and status..
2- 5 LED Indicators The status and descriptions of LED indicators are listed as below: LED Color Function System LED PWR Green Lit when AC power is on and good Per Port LED Link/Act Green Lit when con.
1 - 2 Fig. 1-1 Front view of 16 Port ST/SC Fiber Switch FD X HD X FD X HD X 1 2 3 4 5 6 7 8 2 1 4 5 6 7 8 3 9 1 0 1 1 1 2 1 3 1 4 1 5 1 6 9 10 11 12 13 14 15 16 TX RX TX RX TX RX TX RX TX RX TX RX TX .
An important point after buying a device LevelOne FSW-0800FXT (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought LevelOne FSW-0800FXT yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data LevelOne FSW-0800FXT - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, LevelOne FSW-0800FXT you will learn all the available features of the product, as well as information on its operation. The information that you get LevelOne FSW-0800FXT will certainly help you make a decision on the purchase.
If you already are a holder of LevelOne FSW-0800FXT, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime LevelOne FSW-0800FXT.
However, one of the most important roles played by the user manual is to help in solving problems with LevelOne FSW-0800FXT. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device LevelOne FSW-0800FXT along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
