Instruction/ maintenance manual of the product LB-89658A Lennox International Inc.
Go to page of 8
_ Techrlloal GAS UNITS j _:_b ic=lo.s KITS AND ACCESSORIES Litho U,S.A, ©1997 Lennox industries inc. Datlas, Texas 503,770M 10/97 FURNACE TRANSITION KIT INSTALLATION INSTRUCTIONS FOR FURNACE TRANSITI.
12 - Remove filter from inside of unit (if present). Units with side return air - Disconnect side return air plenum at unit. Units with bottom return air - Disconnect unit base from return air plenum. 13 -Remove G14 unit, B - 614 units with air conditioning IMPORTANT 1 - Set the thermostat to the lowest setting.
FLEXIBLE ISOLATION HANGER TYPICAL G14 INSTALLATION FLEXIBLE BOOT i / SUPPLY AIR j ...... J ...... /_ _ RETURN i i AIR ii EXHAUST PIPE SUPPLY AIR PLENUM INSULATED PAST FIRST ELBOW FLEXIBLE BOOT IN PLENUM -- MUFFLER CONDENSATE DRIP LEG ISOLATION PADS (ISOMODE) (4) .
Note - It is recommended that rack be converted to 20 inch filter size if filter is installed elsewhere in return air duct. 3-In applications where rack uses a 16 inch (50.
EXTERNAL FILTER RACK CONVERSION KIT CAT# 16L23 AND 16L24) From Right S de to Left S de Conf gurat on A= C FILLER PIECE_ ... --_ FRAME HOLDING ANGLE _ -_.
ADHESIVE-BACKED FOAM TAPE INSTALLATION OF SUPPLY AIR TRANSITION AND EXTERNAL FILTER RACK (KIT CAT# 161.23 AND 16L24) _ SUPPLY AIR TRANSITION SECURING SCREWS (2 each side) SUPPLY AIR TRANSITION SMALL END OF TRANSITION INSTALL LARGE END OF TRANSITION TO FRONT OF UNIT.
(2 each side) ,_ T ADHESIVE-BACKED FOAM TAPE INSTALLATION OF SUPPLY AIR TRANSITION AND INTERNAL FILTER RACK SUPPLY AIR TRANSITION (KIT CAT# 16L25) SECURING SCREWS NOTE - FILTERRACK INSTALLATION REQUIR.
G26 CONDENSATE ASSEMBLY (For left or right installation - left shown) HEAT EXCHANGER COIL COMBUSTION AIR BLOWER BRACKET _ // COLD HEADER BOX 1/2 INCH CPVC VENT TERMINATION MUST BE HIGHER THAN COIL PLU.
An important point after buying a device Lennox International Inc. LB-89658A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Lennox International Inc. LB-89658A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Lennox International Inc. LB-89658A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Lennox International Inc. LB-89658A you will learn all the available features of the product, as well as information on its operation. The information that you get Lennox International Inc. LB-89658A will certainly help you make a decision on the purchase.
If you already are a holder of Lennox International Inc. LB-89658A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Lennox International Inc. LB-89658A.
However, one of the most important roles played by the user manual is to help in solving problems with Lennox International Inc. LB-89658A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Lennox International Inc. LB-89658A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
