Instruction/ maintenance manual of the product Winslow (PS40) Lennox Hearth
Go to page of 30
INST ALLA TION AND OPERA TION MANUAL Save These Instructions For Future Reference Pe ll et S to ve s Mo de l W in sl ow ™ (P S4 0) Fr ee -S ta nd in g Pe ll et S to ve P/N 775 ,228 M, R ev . C, 1 1/200 8 US Portland A Fr ench man ual is a vail able upo n re ques t.
2 IM POR T ANT SA F ET Y AND W AR NI IN G IN FOR MA TI ON REA D T HIS MA NUA L I N I TS ENT IRE TY AND UN DER - ST AND THE SE RUL ES TO FOL LOW FO R S AFET Y . W ARNING Do not attempt to alter or modify the construction of the appliance or its components.
3 CONGRA TULA TIONS! When you purchased your new pellet stove, you joined the ranks of thousands of individuals whose answer to their home heating needs, aesthetics, efficiency and our environment. We extend our continued support to help you achieve the maximum benefit and enjoyment available from your new pellet stove.
4 PLANNING YOUR INST ALLA TION W ARNING Che ck all loc al bui ldi ng and safe ty cod es befo re ins tal lat ion . The inst all ati on ins tru cti ons and appr o- pri ate co de r equ ire men ts mus t be fol low ed exa ctl y an d wi tho ut com pro mis e.
5 FEA TURES AND SPECIFICA TIONS CAUTION THE USE OF UNAPPROVED, DIR TY , WET AND/OR HIGH SAL T CONTENT FUEL WILL VOID THE WAR- RANTY! Installation Options • Residential • Vented vertical and horizontal (see venting instructions) • Manufactured home and mobile home • Thermostat or manual operation • Bedrooms Heating • Max.
6 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. STOVE DIMENSIONS CLEARANCES TO COMBUSTIBLES 8 Side V iew Front V iew 26-1/4” (667mm) Front View 31” (7 87m m) The center of the flue is 8- 7/8” above the surface upon which the stove rests.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 7 8” (2 03m m) 3” (7 6mm ) 6-3/4” (1 72m m) 7” 3” (7 6mm ) ( 1 7 8 m m ) 7” (1 78m m) Corner Installations Right Wall Horizontal V ent.
8 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. HEARTH PROTECTION VENT TERMINA TION REQUIREMENTS The floor protector must be a non-combustibl e material extending beneath the stove and to the front and sides as shown below . Minimum Size Hearth Protection 1.
9 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. VENT TERMINA TION LOCA TIONS A = Clearance above grade, veranda, porch, deck, or balcony (min. 12”/30cm) B = Clearance to window or door that may be opened (min. 12”/30cm above - 48”/1.2m below and to the side) C = Clearance to permanently closed window *(min.
10 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Venting This stove is approved for venting with T ype L and T ype PL pellet vent pipe listed to UL 641 and ULC S609. We recommend the use of venting products manufactured by Security Chimneys International.
11 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Masonry Chimney When venting into a masonry chimney , the pellet pipe can terminate just inside the chimney . However , it is recommended to run the pellet pipe to the top of the chimney . Fireplace When venting into a fireplace chimney , the pellet pipe can terminate just above the damper .
12 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Mobile Home Installations Th e fo llo win g ar e re qu ire d fo r in sta ll ati on o f th e Wi nsl ow™ PS4 0 st ov e in mo bil e h om es.
13 Door T rim Installation Instructions Parts List (A): Qty (2) T rim Pieces (Gold, Nickel, Brushed Nickel or Black Nickel ) (6) #10 nuts (6) #10 washers T ools Needed: Qty (1) 3/8” nut driver or socket wrench CAUTION: Always ensure that plated surfaces are clean and free of fingerprints before lighting stove.
14 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 4. Place one washer on each stud. Using a 3/8” nut driver , snug up the nuts on each piece of trim.
15 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Door Grill Installation Instructions Parts Needed: Qty (4) Button Head Screws (already in place in stove) T ools Required: Qty (1) 1/8” allen wrench T o install the Grill: 1. Remove the four button head screws from body of the stove with a 1/8” allen wrench.
16 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Note: The brick panel comes pre-painted with Metallic Black paint. The brick panel may be painted with any color of high-temp paint (paint may discolor with use). 1. Remove the front door of the pellet stove.
17 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 5. Screw in the four tap tights, included with this kit, using a 5/32 allen wrench. 6. Replace the Burn-Pot and check that it is firmly in place (if you can rotate the Burn-Pot it is not installed correctly).
18 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Log Set installation Instructions Kit Contents Part #H5142 Qty (1) left log (B) (1) right log (C) (1) front log (D) (2) log support brackets (E.
19 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. OPERA TION Control Board The control board regulates all functions of the stove. The following is a list of the board’ s components: • Feeding light - lights up when the auger is feeding pellets into the Burn-Pot.
20 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Shut Down Normal - T o turn the stove off, turn the heat selector knob to off. The fans will continue to operate until the control board completes the shut down cycle. Power Outage - If the stove loses electrical power for less than 10 seconds it will continue to operate.
21 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. CLEANING AND MAINTENANCE IMPORT ANT CAUTIONS: • UNPLUG POWER CORD AND ENSURE APPLIANCE IS COLD BEFORE PERFORMING ANY MAINTENANCE WORK. • Some brands of pellets produce more ash and clinkers than others.
22 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. C B B C Figure 45A Inspect Gaskets Inspect the condition of the rope gasket around the door , window and ash drawer , periodically , and replace if necessary . Inspect the die-cut gaskets on the access covers (B and C in Figure 45A ) and replace if necessary .
23 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Front View Looking into the Ash Drawer Cavity with the Ash Drawer Removed A D A D Figure 47 Figure 46B Cleaning the Vent Pipe Soot and Fly-Ash: Formation and Need for Removal The products of combustion will contain small particles of fly-ash.
24 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Proof of Fire Switch This switch needs to be removed and cleaned after every 100 bags of fuel burned. Cleaning Procedure: 1. UNPLUG STOVE! 2. Locate the switch on the combustion blower (see Figure 52 ) .
25 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. COMPONENT INFORMA TION The following is a list of components and their functions. Igniter The Winslow™ PS40 stove comes equipped with an automatic igniter for lighting the fuel when the stove is in the lighting mode.
26 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Draft Adjuster The Winslow™ PS40 stove has a draft adjuster located at the left side of the stove directly in front of the combustion blower .
27 DIAGNOSTIC CODES If the stove operates abnormally , the ready light on the control board will signal the nature of the abnormal operation. The following is a list of pos- sible signals or codes: Re.
28 REPLACEMENT P ARTS Orange Sooty Flames - Glass T urns Black Possible Problem Solution Burn-Pot is dirty Clean the Burn-Pot Vent pipe restricted Clean the vent pipe Flue gas passageways restricted C.
29 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Door T rim (required - sold separately) Cat. No. Model Description 79038 P40DT -B Black 79034 P40DT -G Gold 79037 P40DT -N Nickel 79035 P40DT -.
30 Printed in U.S.A. © 2007 Lennox Hearth Products P/N 775,228M Rev . C, 11/2008 Lennox Hearth Products reser ves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products.
An important point after buying a device Lennox Hearth Winslow (PS40) (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Lennox Hearth Winslow (PS40) yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Lennox Hearth Winslow (PS40) - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Lennox Hearth Winslow (PS40) you will learn all the available features of the product, as well as information on its operation. The information that you get Lennox Hearth Winslow (PS40) will certainly help you make a decision on the purchase.
If you already are a holder of Lennox Hearth Winslow (PS40), but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Lennox Hearth Winslow (PS40).
However, one of the most important roles played by the user manual is to help in solving problems with Lennox Hearth Winslow (PS40). Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Lennox Hearth Winslow (PS40) along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
