Instruction/ maintenance manual of the product ULC-S610 Lennox Hearth
Go to page of 24
EP A Wood-Burning Fireplace P/ N 85 0,0 37 M RE V . K 05 /20 10 MONTE MODEL MONTECITO™ INST ALLA TION AND OPERA TION INSTRUCTIONS SA VE THESE INSTRUCTIONS FOR FUTURE REFERENCE Listed to standards: ULC-S610 and UL-127 Report No. 307-4084 EP A Cert. No.
IMPORT ANT! GENERAL SAFETY PRECAUTIONS. READ AND UNDERST AND THESE SAFETY R UL ES B EF OR E Y OU R F IR S T F IR E . W ARNING T o avoid the risk of damaging fireplace materials and increas- ing the risk of fire, do not use the fireplace to cook or warm food.
T ABLE OF CONTENTS Safety Rules and Specifications for Mobile or Manufactured Home Installation ......................... Page 2 Introduction ...................................... Page 3 Parts Required ................................. Page 3 Optional Equipment .
Building a Fire (starting and maintaining a fire) T o start a fire, place several crumpled up balls of newspa per in the firebox. Place small dry pieces of kindli ng on top of the paper , criss-c rossi ng the kindling so that there are air spaces in between.
A. Negative pressure in the house - As the fire burns, air goes up the chimney . This air must be replaced through leakage into the hous e or throug h the outsi de air duct. When operating the Montecito fireplace, open a nearby window temporaril y to check if there is adequate replacement air supply .
REFRACTORY REPLACEMENT The intense heat of the fire will normally cause hairline cracks in the refractory . These cracks can be minimized by proper curing as described in“First Fires”.They willnot normallydimin - ish the effectiveness of the refractory .
Facade Installation In sta ll the Fac ade pe r i nst ruc ti ons pr ovi ded in Fa cad e K it (o rde red se pa rat ely - se e P age 2 0 ). Framing, Facing And Mantel The construction of the framing, facing, and mantel must be in accordance with the stan- dards and the following illustrations ( Figures 10 and 11 ): A.
FRAMING DIMENSIONS Fireplace Opening Width A 36-1/4” 921 mm B 42” 1067 mm C 30-1/16” 764 mm D 13-1/2” 343 mm E 77” 1956 mm F 37-1/2” 953 mm G *24-1/2” 603 mm J 53-3/4” 1365 mm K 8” 2.
Figure 9 Insulated Chase Construction Figure 11 Floor Ceiling Wall • Must have the same firestopping resistance as adjacent wall. • Must have the same insulation as adjacent ceiling.
HOT AIR DUCTING INST ALLA TION The Montecito™ wood burning fireplace is approved for use with a Gravity kit (hot air ducting system). Gravity Kit The gravity kit is designed for double hot air outlets and includes: (See Figure 14 ). - T wo(2)telescopiclengths8”I.
Figure 17 OUTSIDE AIR KIT It is mandatory to install an outside air connec- tion to the Montecito™ wood burning fireplace. The following components are required and are included with the fireplace.
Figure 18 OUTSIDE CONNECTION Figure 19 Aluminum T ape Aluminum T ape Fireplace Connection Plastic Cover Insulation Flexible Pipe Fireplace 5. All chimney installations must include at least one support. Re- ducing the amount of chimney weight on the fireplace will help avoid the noise created when the fireplace expands.
CHIMNEY INST ALLA TION INSTRUCTIONS 1. Cut and frame the holes in the ceiling, floor and roof where the chimney will pass (see Figure 21 ). Use aplumb-bob tolineup the centerof theholes.
Roof Down Slope Hole Size S L O P E A S H T + / H T 6 1 0 3 + S - 2 1 00 + / H T 6 0 0 0 + A C R o o f P it c h 6 ” 6 ” 6 ” 0 * 1 2 - 3 /8 ” ( 3 1 4 m m ) 1 4 - 1 /8 ” ( 3 5 9 m m ) 1 5 ” .
Figure 26 Ch im ne y 6” Elbo w Offset & Height One Length Between Elbows T wo Lengths Between Elbows 8” 12” 18” 24” 36” 48” 8” & 48” 1 2” & 4 8 ” 1 8” & 4 8 ”.
Figure 27 OFFSET CHIMNEY INST ALLA TION Chimney AC Support ACRS Starter Section Rain Cap Collar Roof Flashing Offset Support Insulated Wall Radiation Shield Framing 2” x 3” Figure 28 Straps Straps OF FSE T CHI MN EY IN ST ALLA TIO N WIT H W ALL P ENE TR A TIO N Note: In cold areas it is recom- mended to protect the chimney in a insulated chase.
If possible, you should choose a location where the chimney will pass throu gh the house without cutting floor or roof joists (see fireplace dimen- sions Page 9 ). Usually , no additional oor support is needed for the fireplace.
CHIMNEY SUPPORT INST ALLA TION Universal Roof Support This support has three possible uses: 1. ForASHT+/ HT6103+andS-2100+/ HT6000+,itmust beusedon a roof to support the chimney . 2. It may be used on a floor , ceiling or roof above an offset to support the chimney above the offset.
INST ALLA TION INSTRUCTIONS FOR MASONRY APPLICA TION WARNING: Before starting the installation, the masonry chimney must be inspected by a qualified chimney sweep. The following requirements must be respected: 1. The chimney must be absolutely clear of any soot residue or creosote.
Installation Accessories Description Cat./ Part No. Facades (Required - Order Separately) Montecito™ Facade Black, MFBK H4843 Montecito Facade Brushed Nickel, MFBN H4844 Montecito Facade Hammered St.
CHIMNEY - P ARTS AND COMPONENTS LISTS Firep lace Model MONTE - Approved Venti ng Compone nts manufa ctured by Security Chimneys International only . • 6” diameter chimney - AC (air cooled), Secure T emp™ ASHT+ (or Nova T emp™ HT6103+) and Secure T emp S-2100+ (or Nova T emp HT6000+).
CHIMNEY - P ARTS AND COMPONENTS LISTS (AC) Air -Cooled Chimney System* 6” I.D. and 11” O.D. Air Cooled, Stainl. Steel inner and zinc coated steel exterior * AC Ch i m ne y is N O T re co m m en d .
CLEARANCE TO COMBUSTIBLES The following clearances meet the minimum requirements for a safe installation; Side wall: 17”(324mm)measuredfromthereplaceside Ceiling: 6’.
Printed in Canada © 2006 Lennox Hearth Products P/N 850,037M REV . K 05/2010 24 Y our Fireplace's Model Number ________________________________________ Y our Fireplace's Serial Number _____.
An important point after buying a device Lennox Hearth ULC-S610 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Lennox Hearth ULC-S610 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Lennox Hearth ULC-S610 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Lennox Hearth ULC-S610 you will learn all the available features of the product, as well as information on its operation. The information that you get Lennox Hearth ULC-S610 will certainly help you make a decision on the purchase.
If you already are a holder of Lennox Hearth ULC-S610, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Lennox Hearth ULC-S610.
However, one of the most important roles played by the user manual is to help in solving problems with Lennox Hearth ULC-S610. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Lennox Hearth ULC-S610 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
