Instruction/ maintenance manual of the product X-Fires WS Lennox Hearth Products
Go to page of 20
Report No. 317-F-1 1-5 IN S T AL L A TI O N AN D O PE R A TI O N M AN UA L Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance. WHA T TO DO IF YOU SMELL GAS • Do not light any appliance. • Do not touch any electrical switches; do not use any phone in your building.
2 • Children and adults should be alerted to the hazard of high surface temperature and should stay away to avoid burns or clothing ignition. • Y oung children should be carefully super vised when they are in the same room with the heater . • Do not place clothing or other flammable material on or near the heater .
3 2.0 GENERAL INFORMA TION This appliance is a high efficiency , unvented, flame effect gas heater . It provides radiant and convected warmth both efficiently and safely utilizing the latest type catalytic convertor burner technology .
4 6.0 BURN-IN PERIOD On initial light up of a new appliance, the ‘newness’ will burn off within the first few hours of operation. During this period some smoke may be emitted from outlet grill, this should be no cause for concern. Accord- ingly , the room should be well ventilated with all windows and doors open during this period.
5 8.0 COMBUSTION AND VENTILA TION AIR This heater shall not be installed in a confined space or unusually tight construction unless provisions are provided for adequate combustion and ventil ation air .
6 9.0 SITE REQUIREMENTS This appliance is designed to be wall-hung. Do not recess any part of the appliance into the wall. This appliance may be installed in any room in a home except bedrooms or bathrooms - or areas where large amounts of steam are likely to be generated.
7 Non-concealed gas connections may be made using the entry points on the base of the firebox. A concealed gas connection may be made using the knockout hole in the center back of the firebox. Select the most appropriate entry point and knock out the relevant hole.
8 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE Figure 3 - Wall Fixing T emplate FPO After having selected the final mounting position of the appliance, taking into account the site requiremen.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE 9 It is recommended that the burner height, where possible, should be approximately 4 ft. from the floor . This will give the best viewing position. When selecting the height, ensure that the clearance to the ceiling is 32" minimum, as specified on Page 6 .
10 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE 14.0 CHECKING THE BURNER There are no imitation fuel bed components, such as logs or rocks, to install. The appliance features a ribbon burner which is designed to produce a continuous band of flame over its length.
11 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE 16.0 CHECKING THE GAS CONNECTIONS T urn on gas supply and test for gas leaks using a gas leak test solution (also referred to as bubble leak solution).
12 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE 18.0 SP ARK GAP Figure 8 - Proper Spark Gap 1/8" to 3/16" Spark Gap 19.0 BRIEFING THE CUSTOMER W ARNING Do not add log s or orn ame nts suc h as pin e co nes , ver mic uli te or rock wo ol.
13 W ARNING Any chan ge to this heat er or its con tro ls can be dan ger ous . W ARNING No adju stm ent s are to be mad e to the OD S pi lot sy st em . T am pe ri ng wi th th is sys te m ca n be ex tr em el y haz ard ous . W ARNING Y ou mus t kee p co ntr ol ar eas , bur ner s an d cir cul at- ing a ir pass age way s of ap pli anc e c lea n.
14 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE 21.0 CA T AL YSTS W ARNING Do not blo ck the ca tal ys ts or the app li an ce out le t gri ll . Blo cka ge may cause high car bon monox ide level s and /or b rea kag e o f t he gla ss fac ia pan el.
15 FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTL Y , A FIRE OR EXPLOSION MA Y RESUL T CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. A. This appliance has a pilot which must be lit with a piezo spark igniter .
16 24.0 TROUBLESHOOTING GUIDE PROBLEM CORRECTIVE ACTION Igniter sparks but pilot does not light • No gas to Pilot, check the gas line connections. • Air not fully purged. Purge supply or wait longer . • Spark grounding to metal work, reset gap correctly .
17 WARNING CLEARANCES FROMCOMBUSTIBLEMATERIALS F860041/A The following clearances must be maintained at all times. Failure to do so may result in the risk of a fire. For full information refer to the instruction manual provided with the heater. Note : Zero clearance from bottom of heater frame required for hard combustible floors.
18 26.0 POSITIONING OF FIELD REMOV ABLE P ARTS Glass Door Removal: Remove the four (4) screws indicated, then lift door off. Figure 12 W ARNING Fai lur e to pos iti on the par ts in acc ord anc e wi t.
19 NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE 27.0 SPECIFICA TIONS X-FIRE-WIDESCREEN Surround Kits Cat. No. Model Description S h ip . Wt . Ship. Volume H7228 X - FI RE -W S- L Limestone Surround 71 l b. 6 . 15 c u. f t. H7229 X - FI RE -W S- G Granite Surround 7 1 l b.
20 Printed in U.S.A. © 2008 Lennox Hearth Products P/N 506023-05 REV . A 11/2008 Lennox Hearth Products reser ves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products.
An important point after buying a device Lennox Hearth Products X-Fires WS (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Lennox Hearth Products X-Fires WS yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Lennox Hearth Products X-Fires WS - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Lennox Hearth Products X-Fires WS you will learn all the available features of the product, as well as information on its operation. The information that you get Lennox Hearth Products X-Fires WS will certainly help you make a decision on the purchase.
If you already are a holder of Lennox Hearth Products X-Fires WS, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Lennox Hearth Products X-Fires WS.
However, one of the most important roles played by the user manual is to help in solving problems with Lennox Hearth Products X-Fires WS. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Lennox Hearth Products X-Fires WS along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
