Instruction/ maintenance manual of the product LSBV-3628MP Lennox Hearth
Go to page of 16
1 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance. What to do if you smell gas: • DO NOT light any appliance. • DO NOT touch any electrical switches, do not use any phone in your building.
2 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. TABLE OF CONTENTS Packaging ........................................ page 2 Introduction ..................................... page 2 Massachusetts and New York Requirements ..........................
3 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Carbon Monoxide Poisoning: Early signs of carbon monoxide poisoning are similar to the flu with headaches, dizziness and/or nausea.
4 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Venting Gas Vent Rule – Gas vent caps are not permit- ted within 8 feet (2.4 mm) of a vertical wall or similar obstruction.
5 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. FRAMING SPECIFICATIONS Figure 4 Figure 5 Figure 6 Framing Dimensions ASSEMBLY STEPS The typical sequence of installation follows, however, each installation is unique resulting in variations to those described.
6 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Step 3. Position the Appliance - Slide the fireplace into prepared framing or position fire- place in its final position and frame later. Refer to fireplace drawings and specifications on pages 4 and 5 for framing dimensions and details.
7 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Figure 10 Step 4. Install the Vent System & Exterior Termination - Slip a 10" (254 mm) B-Vent system over the appliance collar ( Figure 10 ) and secure with four sheetmetal screws (# 8 or larger).
8 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Figure 14 1. Route a 3-wire 120V 60Hz power supply line to the appliance junction box wires and ground (Figures 13 ). 2. After wiring is complete, replace the appli- ance junction box cover and secure with the hex head screws previously removed.
9 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Figure 15 Note: Supply wires may be alternatively connected to the outlet using the screw terminals, however the black supply wire must be wired to a terminal that is opposite (across the outlet) the point where the white supply wire is connected ( Figure 15 ).
10 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Figure 17 Figure 18 Refer to the Homeowners Care and Operation Instructions for detailed log description and placement instructions. Log set shown in this document (Figure 17 ) is typical, installation of all sets are similar.
11 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Figure 22 Adjustment To adjust the flame, position the air shutter to the nominal setting (Figure 22 ).
12 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. INSTALLATION ACCESSORIES The following accessory items are available for use in the installation of this appliance. Figure 24 COLD CLIMATE INSULATION If you live in a cold climate, seal all cracks around your appliance with noncombustible material and wherever cold air could enter the room.
13 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Wall Switch Kit 85L87 FWSK Outside Combustion Air Kits (with duct) 81L87 FOAK-4 (without duct) 81L88 FOAK-4LD Outside Air Kits Models FOAK-4 and FOAK-4LD Outside Air kits are available with duct (FOAK-4) and without duct (FOAK-4LD) for use if outside combustion air is re- quired or desired.
14 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Figure 25 Pressure Regulator Remove These Components Step 1. Turn off the gas supply to the appli- ance. Remove the front glass door (if used) from the appliance. Access the control com- partment. Step 2.
15 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Figure 28 Figure 29 Step 9. Reassemble all removed components by reversing the procedures outlined in the preceding steps.
16 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. Lennox Hearth Products reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor for fireplace code information.
An important point after buying a device Lennox Hearth LSBV-3628MP (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Lennox Hearth LSBV-3628MP yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Lennox Hearth LSBV-3628MP - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Lennox Hearth LSBV-3628MP you will learn all the available features of the product, as well as information on its operation. The information that you get Lennox Hearth LSBV-3628MP will certainly help you make a decision on the purchase.
If you already are a holder of Lennox Hearth LSBV-3628MP, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Lennox Hearth LSBV-3628MP.
However, one of the most important roles played by the user manual is to help in solving problems with Lennox Hearth LSBV-3628MP. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Lennox Hearth LSBV-3628MP along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
