Instruction/ maintenance manual of the product EBVI30 Lennox Hearth
Go to page of 20
B-VENT GAS FIREPLACE HEA TER INSER TS RETAIN THIS MANUAL FOR FUTURE REFERENCE Suitable for installation into masonry or factor y built fi replaces P/N 775,155M Rev . D,12/2005 FOR YOUR SAFETY Do not store or use gasoline or other fl ammable vapors or liquids in the vicinity of this or any other appliance.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 2 It is imperative that the control compart- ment, burners and circulating air passage ways of the appliance be kept clean. S'assurer que le brùleur et le compartiment des commandes sont propres.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 3 T able 2 shows the main burner gas orifi ce size for the elevations indicated. Model No. Orifi ce Size Elevation Feet (meters) Nat. Gas Prop. Gas EBVI25 #41 (.096") #53 (.0595") 0-4500 (0-1372) EBVI30 #37 (.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 4 MAINTENANCE The appliance and venting system should be thoroughly inspected before initial use and at least annually by a qualifi ed ser vice technician. However , more frequent periodic inspections and cleanings should be performed by the homeowner .
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 5 Small Area Paint T ouch-up The fi nish of the insert body and surround (optional) is a high-quality powdercoat.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 6 Maintenance T ask Accomplishing Person Procedure Inspecting/Cleaning Burner , Logs and Controls Qualifi ed Service T echnician Inspect valve and ensure it is properly operating. Check piping for leaks.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 7 PROCEDURE FOR REMOVING ST ANDARD GLASS DOOR ASSEMBL Y Burner Flame Appearance BURNER ADJUSTMENT Flame Appearance and Sooting Proper fl ame appearance is a fl ame which is blue at the base and becomes yellow/orange in the top of the fl ame.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 8 If the burner fl ame appearance differs greatly from what is shown in Figure 13 (see Burner Flame Appearance) , some adjustment from the factor.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 9 1. Place the rear log onto the two corresponding locating pins at the back of the fi rebox as shown in Figure 16 . 2 . Place the Front Right Log onto the two corresponding locating pins as shown in Figure 17 .
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 10 8. Place the glowing embers on the burner as shown in Figure 23 . One package of ember material has been included with this log set Y ou will not need to use the entire bag.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 11 T o light the burner , rotate the gas valve control knob counterclockwise to the “ON” position then turn “ON” the off/on switch mounted.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 12 Figure 28 If original wire as supplied must be replaced, it must be replaced with T ype AWM 105°C, 18 gauge wire.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 13 Cat. No. Model Description 89L36 WTK Wall Thermostat KiT Wall Thermostat The wall thermostat kit provides temperature control for optimum comfort. Cat.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Cat. No. Model Description H1503 SKS-25 Beveled Surround, Small, EBVI25 H1504 SKM-25 B eveled Surround, Medium, E B VI25 H0881 SKS-30 Beveled Surr.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 15 H I L O W TPTH TP TH P I L O T P I L O T O N it it O F F OUT OUT IN IN 6. W ait fi ve (5) minutes to clear out any gas. If you then smell gas, STOP! Follow “B” in the safety information above on this page.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 16 INSTRUCTIONS D’ALLUMAGE – V ANNE GAZ MILLIVOL T INSTRUCTIONS D'ALLUMAGE 8. Enfoncez le bouton de réglage jusqu’au fond et gardez-le enfoncé.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 17 REPLACEMENT P ARTS LIST Gas Controls Item # Part/Cat. No. Description Where Used 1 67L7001 Pilot Assembly , NG/LP EBVI25 & EBVI30 2 67L6801.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. REPLACEMENT P ARTS DIAGRAMS 9 15 16 17 3 4 2 12 7b O N O F F P I L O T L O H I 5b 1 8 19 18 13 20 14b 21a 21b 14a 10b 10a 7a 5a 6 18.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. 19 TROUBLESHOOTING THE MILLIVOL T GAS CONTROL SYSTEM Note: Before troubleshooting the gas control system, be sure external gas shut off valve (located at gas supply inlet) is in the “ON” position.
NOTE: DIAGRAMS & ILLUSTRA TIONS ARE NOT TO SCALE. Printed in U.S.A. © LENNOX HEARTH PRODUCTS 2003 P/N 775,155M Rev . D 12/2005 LENNOX reserves the right to make changes at any time, without notice, in design, materials, specifi cations, prices and also to discontinue colors, styles and products.
An important point after buying a device Lennox Hearth EBVI30 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Lennox Hearth EBVI30 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Lennox Hearth EBVI30 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Lennox Hearth EBVI30 you will learn all the available features of the product, as well as information on its operation. The information that you get Lennox Hearth EBVI30 will certainly help you make a decision on the purchase.
If you already are a holder of Lennox Hearth EBVI30, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Lennox Hearth EBVI30.
However, one of the most important roles played by the user manual is to help in solving problems with Lennox Hearth EBVI30. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Lennox Hearth EBVI30 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
