Instruction/ maintenance manual of the product CS-1004 Lenco Marine
Go to page of 19
OWNER’S MANUAL Mobile Audio System • PLL Synthesizer Stereo Radio • RDS (Radio Data System) Operation • Digital Compact Disc Player • Automatic Memory Storing • Full Detachable Panel •P .
CONTENTS Installation ...........................................3 T ake out screw befor e installation.........3 DIN Front-Mount (Method A) ................3 Installing the unit .................................3 Removing the unit ...................
INST ALLA TION Notes: • Choose the mounting location where the unit will not interfere with the normal driving function of the driver . • Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly .
INST ALLA TION 6. Mount the sleeve by inserting the sleeve into the opening of the dashboard and bend open the tabs located around the sleeve with a screwdriver . Not all tabs will be able to make contact, so examine which ones will be most effective.
DIN REAR-MOUNT (Method B) If your vehicle is a Nissan, Toyota, follow these mounting instructions. Use the screw holes marked T (T oyota), N (Nissan) located on both sides of the unit to fasten the unit to the factory radio mounting brackets supplied with your vehicle.
USING THE DET ACHABLE FRONT P ANEL REMOVING THE FRONT P ANEL 1. Pr ess the release button (REL) on the front panel and pull of f the front panel. 2. Keep fr ont panel into the case. INST ALLING THE FRONT P ANEL To install the front panel, insert the panel into the housing and make sure the panel is properly installed.
WIRING CONNECTION ISO Connection ISO SOCKET PIN OUT Part A Power Connection Part B Speaker Connection 1. Free 1 + 2. Free 2 – 3. Free 3 + 4. Memory (+B permanent) 4 – 5. T rip line for fully automatic antenna 5 + 6. Free 6 – 7. Main power supply (+B ignition) 7 + 8.
OPERA TION LOCA TION OF KEYS 14 4 2 16 17 13 8 9 10 7 11 1 12 3 20 21 6 22 23 19 18 15 5 24 GB-8.
OPERA TION SWITCHING ON/OFF THE UNIT Switch on the unit by pressing any button (except REL button (7) and EJECT button (4)). When system is on, press PWR button (9) to turn off the unit. F ACEPLATE RELEASE Press REL button (7) to detach the removable faceplate.
OPERA TION c) RETUNE L, RETUNE S mode The initial time of automatic T A search or PI sear ch mode is selected. When PI information is not caught for retune time, the radio start to retune to next same PI station.
OPERA TION “NO PTY” -> Each displaying time is several seconds, and come back to 1’st position after several seconds. Notes: - CT = clock time - FREQ. = frequency EQUALIZA TION Press PEQ button (19) to turn on equalization function and to select desired audio mode.
OPERA TION immediately to switch on or off R.D.S. mode. Whenever R.D.S. is switched on, symbol “AF” appears on the display . Program name is displayed on receiving a R.D.S. station. “AF” starts blinking if the broadcasting signal getting worse.
OPERA TION R.D.S. T A information was received from curr ent station and the radio switched to that R.D.S. linked station, but no information could not be received because the R.D.S. linked station is located too far from that area. So the radio is switched back to current station again.
OPERA TION • PLA YING ALL TRACKS IN RANDOM Press SHF button (23) to play all tracks on CD in random order . Press again to cancel the function. • EJECTING A DISC Press EJECT button (4) to stop CD playing and eject the disc from the disc slot (5).
OPERA TION unit searches the track after few seconds, even if the enter button is not pressed. Searching Dir ectory or File Name Press AMS (MP3) button for two times.
OPERA TION KEY Assigned IN Searching mode (T able 1) AUDIO SELECT UP/DOWN & TUNE/SEEK/TRACK UP/DOWN buttons: Searching file and dir ectory during Navigation. MIXED-CD OPERA TION If available, the unit can play the mixed- CD disc (the disc contains both CD audio tracks and MP3 files).
Recordable Rewritable DISC NOTES: A. Notes on discs : 1. Attempting to use nonstandard shape discs (e.g. square, start, heart) may damage the unit. Be sure to use round shape CD discs only for this unit. 2. Do not stick paper or tape etc., onto the label side or the recording side of any discs, as it may cause a malfunction.
GENERAL Po w er Supply Requirements : DC 12 V olts, Negative Ground Chassis Dimensions : 178 (W) x 160 (D) x 50 (H) Tone Controls - Bass (at 100 Hz) : ± 10 dB - T r eble (at 10 KHz) : ± 10 dB Maximum Output P ow er : 4 x 15 W atts Current Drain : 5 Amper e (max.
TROUBLE SHOOTING Before going thr ough the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer . Symptom Cause Solution No power . The car ignition switch is If the power supply is pr operly not on.
An important point after buying a device Lenco Marine CS-1004 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Lenco Marine CS-1004 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Lenco Marine CS-1004 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Lenco Marine CS-1004 you will learn all the available features of the product, as well as information on its operation. The information that you get Lenco Marine CS-1004 will certainly help you make a decision on the purchase.
If you already are a holder of Lenco Marine CS-1004, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Lenco Marine CS-1004.
However, one of the most important roles played by the user manual is to help in solving problems with Lenco Marine CS-1004. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Lenco Marine CS-1004 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
