Instruction/ maintenance manual of the product TPS400 Leica
Go to page of 36
User Manual Mining Application Program English V ersion 1.0 TPS400 Series.
TPS400 Mining Manual-1.0.0en 2 T o use equipment in the permitted manner , please refer to the detailed safety instructions in the TPS400 User Manual (English version). The quick way to start with the TPS400 Mining Programs. The quick way to start © 2003 Leica Geosystems AG Heerbrugg, ® All rights reserved.
TPS400 Mining Manual-1.0.0en 3 Contents - Overview Contents - Overview Introduction ......................................................................... 5 Peg Survey .......................................................................... 6 Front Line Peg .
TPS400 Mining Manual-1.0.0en 4 Contents Introduction ................................................ 5 How to use this manual ............................... 5 Symbols used in the sequence of operation ................................................
TPS400 Mining Manual-1.0.0en Introduction 5 Introduction How to use this manual This manual describes the basic operation of the TPS400 Mining field programs. It shall be used together with a TPS400 instrument. For detailed description about the whole functionality of the TPS400 instrument please refer to the TPS400 User Manual.
TPS400 Mining Manual-1.0.0en Peg Survey 6 Peg Survey Mining_z01 Introduction The application "Peg Survey" is used to establish a forward peg (point). It is used to control the intermediate horizontal angle between backsight and foresight points.
TPS400 Mining Manual-1.0.0en Peg Survey 7 Before starting Peg Survey Data uploading using "Mining Editor" • Station coordinates (East, North, Height, Grade elevation) • Backsight point c.
TPS400 Mining Manual-1.0.0en Peg Survey 8 Start and execution Peg Survey > Step 3 Choose "Start" by pressing [F4], then enter point number (PtID) and instrument height (hi) for the station. The sign for the instrument height (hi) is normally negative.
TPS400 Mining Manual-1.0.0en Peg Survey 9 Error messages Number of sets: One set means to measure two times the backsight point and two times the foresight point in both faces. The meaning of set is described: Mining_z02 One Set The user must complete the number of sets as preset in the tolerance setting.
TPS400 Mining Manual-1.0.0en Peg Survey 10 Sequence: It defines the measuring sequence. Options: • BFFB Backsight-Foresight- Foresight-Backsight • BFBF Backsight-Foresight- Backsight-Foresight • BBFF Backsight-Backsight- Foresight-Foresight [OK] Leaves this dialog and proceed to the next dialog.
TPS400 Mining Manual-1.0.0en Peg Survey 11 Proceeding Peg Survey , continued > Step 7 Enter a desired foresight point number (PtID). [OK] Saves the foresight point number and proceed to the measure dialog. Sample dialog: > Step 5 Enter the reflector height (hr) for the backsight point, if required.
TPS400 Mining Manual-1.0.0en Peg Survey 12 Proceeding Peg Survey , continued [REJECT] Reject the measurement and measure the set again. [ACCEPT] Accept the result and continue with the next set. Sample dialog: > Step 8 Enter the reflector height (hr) for the foresight point, if required.
TPS400 Mining Manual-1.0.0en Peg Survey 13 Results Sample dialog: T olerances dialog: • dHz: Residual on the horizontal angle • dHD: Residual on the horizontal distance • dH: Height residual •.
TPS400 Mining Manual-1.0.0en Peg Survey 14 Results, continued Sample dialog: [P AGE] Sample dialog: Result dialog: • mHz: Average intermediate horizontal angle between backsight point and foresight .
TPS400 Mining Manual-1.0.0en Peg Survey 15 Results, continued [OK] Quits the program. [EXIT] T erminates the measurement and returns to the start- up menu.
TPS400 Mining Manual-1.0.0en Front Line Peg 16 Front Line Peg Introduction The application "FLP" is used to mark a new line peg (Front line peg). This application is similar to "Peg Survey" and there is only one set of measurement required .
TPS400 Mining Manual-1.0.0en Grades 17 Grades Mining_z04 Introduction "Grades" application is used to mark gradelines along the side walls of the mines (tunnels). It allows users to input the slope gradient and an offset concerning the grade point.
TPS400 Mining Manual-1.0.0en Grades 18 Start and execution Grades Menu dialog of "FLP": Sample dialog: If the slope gradient (station until foresight point) is the same like the slope gradient (backsight point until station) then continue direct with > Step 3 .
TPS400 Mining Manual-1.0.0en Grades 19 Mining_z06 Start and execution Peg Survey , continued Mining_z05 150 1 H New Gradeline > Step 1 Enter the slope gradient (proportion e.g. 1:150). Slope gradient explained: Gradeline > Step 2 Enter the height difference.
TPS400 Mining Manual-1.0.0en Grades 20 Gradeline Marking Sample dialog: > Step 4 Enter a desired point number (PtID). > Step 5 Aim at target point and measure. [MEASURE] or [DIST]/[REC] Measurement is triggered and stored in the internal memory .
TPS400 Mining Manual-1.0.0en Grades 21 Results Grades computes the height difference (dHgt) between measure point and stake out point and the horizontal distance (dHD) along the foresight line.
TPS400 Mining Manual-1.0.0en Grades 22 Results, continued Saving data The following result data are stored in the internal memory: Measurement data: PtID: Point number Hz: Horizontal angle V: V ertica.
TPS400 Mining Manual-1.0.0en Offset 23 Offset Introduction "Offset" application is generally used to obtain sections of the tunnels for volume computation as well as mapping of the tunnels. It allows users to input offset value (left, right, up and down) and computes after measurement the actual coordinates of the tunnel walls.
TPS400 Mining Manual-1.0.0en Offset 24 Start and execution Offset Menu dialog of "FLP": Sample dialog: > Step 1 Enter a desired point number (PtID) and the offset value.
TPS400 Mining Manual-1.0.0en Offset 25 Start and execution Offset, continued Definition of offset explained: Mining_z10 Up Down Right Left > Step 3 Aim at target point and measure. [MEASURE] or [DIST]/[REC] Measurement is triggered and stored in the internal memory .
TPS400 Mining Manual-1.0.0en Offset 26 Results Saving data The following result data are stored in the internal memory: Measurement data: PtID: Point number Hz: Horizontal Angle V: V ertical Angle HD: Horizontal distance SD: Slope distance The measurement data are already corrected.
TPS400 Mining Manual-1.0.0en Setting out 27 Setting out This program calculates the required elements to stakeout points from coordinates or manualy entered angles, horizontal distances and heights. Setting out differences can be displayed continuously .
TPS400 Mining Manual-1.0.0en Setting out 28 Orthogonal setout The position offset between measured point and setout point is indicated in a longitudinal and transversal element. dLength: Longitudinal of fset: positive if nominal point further away . dTrav .
TPS400 Mining Manual-1.0.0en T ie Distance 29 T ie Distance The application Tie Distance computes slope distance, horizontal distance, height difference and azimuth of two target points measured online , selected from the Memory or entered using the Keypad .
TPS400 Mining Manual-1.0.0en T ie Distance 30 Softkeys - polygonal method: [NewPt 1] An additional missing line is computed. Program starts again (at point 1). [NewPt 2] Point 2 is set as starting point of a new missing line. New point (Pt 2) must be measured.
TPS400 Mining Manual-1.0.0en Mining Editor 31 Mining Editor Introduction "Mining Editor" (PC Program Package) is a Windows-based program used for the data exchange between the TPS400 Series and the PC. Installation on the PC The installation program for the "Mining Editor" can be found on the CD-ROM supplied.
TPS400 Mining Manual-1.0.0en Mining Editor 32 • Define and upload T olerances Defining tolerances, editing tolerances (password protected), uploading tolerances • Creating fixpoint files Creating .
TPS400 Mining Manual-1.0.0en Mining Editor 33 First Example (Creating fixpoint files, define tolerances, uploading) Creating fixpoint files > Step 1 Open a new file: File ! ! ! ! ! New > Step 2 Enter point number , coordinates, backsight reference point, grade elevation.
TPS400 Mining Manual-1.0.0en Mining Editor 34 First Example (Creating fixpoint files, define tolerances, uploading), continued > Step 5 a) Select a tolerance type (Primary , Secondary , T ertiary).
TPS400 Mining Manual-1.0.0en Mining Editor 35 Second Example (Importing of fixpoints in ASCII format) Process import fixpoint files The "Mining Editor" allows to import fixpoint files in ASCII format. > Step 1 File ! ! ! ! ! Open > Step 2 ASCII-File search and select.
Leica Geosystems AG CH-9435 Heerbrugg (Switzerland) Phone +41 71 727 31 31 Fax +41 71 727 46 73 www .leica-geosystems.com Printed in Switzerland - Copyright Leica Geosystems AG, Heerbrugg, Switzerland 2003 Original text 734337-1.
An important point after buying a device Leica TPS400 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Leica TPS400 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Leica TPS400 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Leica TPS400 you will learn all the available features of the product, as well as information on its operation. The information that you get Leica TPS400 will certainly help you make a decision on the purchase.
If you already are a holder of Leica TPS400, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Leica TPS400.
However, one of the most important roles played by the user manual is to help in solving problems with Leica TPS400. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Leica TPS400 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
