Instruction/ maintenance manual of the product 788472 Leica
Go to page of 22
Leica DISTO TM E7400x The original laser distance meter.
Leica DISTO TM E7400x 788480a 1 EN Table of Contents Instrument Set-up - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Introduction - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - .
Leica DISTO TM E7400x 788480a 2 EN Instrument Set-up Introduction The safety instructions and the user manual should be read through carefully before the product is used for the first time. The person responsible for the product must ensure that all users understand these directions and adhere to them.
Leica DISTO TM E7400x 788480a 3 EN Instrument Set-up Display Horizontal measurement Units Stake out Ceiling area Wall area Circumference Measuring reference 2nd result Area / Volume Tilt angle Info Sl.
Leica DISTO TM E7400x 788480a 4 EN Operations Switching ON/OFF Clear Message Codes ON OFF 2 sec Device is turned OFF. i Press ON but- ton 2 sec to st art continuous laser mode. 1x Undo last action. 2x Leave actual func- tion, go to de fault operation mode.
Leica DISTO TM E7400x 788480a 5 EN Operations Multifunctional endpiece i The orientation of the endpiece is automaticall y detected and the zero point is accordingly ad- justed. Distance unit setting Tilt unit setting Switch between the following unit s: 0.
Leica DISTO TM E7400x 788480a 6 EN Operations Beep ON/OFF Illumination ON/OFF 2 sec simulta ne- ously 2 sec simultane- ously Keypad lock ON Keypad lock OFF 2 sec simulta ne- ously PRESS MINUS 1 withi .
Leica DISTO TM E7400x 788480a 7 EN Measuring Functions Measuring single distance 1 Aim active laser at target. 2 8.532 m 3 i Target surfaces: Measuri ng errors can occur when measuring to col- ourless liquids, glass, styrofo am or semi-permeable surfaces or when aiming at high gloss surfaces.
Leica DISTO TM E7400x 788480a 8 EN Measuring Functions Area 1 1x 2 Aim laser at first target point. 3 4 Aim laser at sec- ond target point. 24.352 m 2 5 i The result is shown in the main line and the mea sured va lue above . Partial Measurements: Press + or - after starting the fir st measurement.
Leica DISTO TM E7400x 788480a 9 EN Measuring Functions Volume 1 2x 2 Aim laser at first target point. 3 4 Aim laser at sec- ond target point. 5 6 Aim laser at third target point. 78.694 m 3 7 i The result is shown in the main line and the measured value above.
Leica DISTO TM E7400x 788480a 10 EN Measuring Functions Triangular area 1 3x 2 Aim laser at first target point. 3 4 Aim laser at sec- ond target point.
Leica DISTO TM E7400x 788480a 11 EN Measuring Functions Pythagoras (3-point) 1 4x 2 Aim laser a t upper point. 3 4 Aim laser at rec- tangular point. 5 6 Aim laser at lower point. 8.294 m 7 i The result is shown in the main line and the measured distance above.
Leica DISTO TM E7400x 788480a 12 EN Measuring Functions Pythagoras (partial height) 1 5x 2 Aim laser a t upper point. 3 4 Aim laser at 2nd point. 5 6 Aim laser at rec- tangular point. 2.602 m 7 i The result is shown in the main line and the measured distance above.
Leica DISTO TM E7400x 788480a 13 EN Measuring Functions Stake out i Two different distances (a and b) can be entered to mark off de- fined measured lengths. 1 2 3 a b b a = b 1 2 3 a b b a = b 1 .000 m 1 6x 1. 01 2 m 2 Adjust value "a". 3 Approve value "a".
Leica DISTO TM E7400x 788480a 14 EN Measuring Functions Smart Horizontal Mode 1 Aim laser at tar- get. 2 0.032 m 5.204 m 40.8 ° 4.827 m x z x y z y 3 (up to 360° and a transverse tilt of ±10°) i Press key again to switch off horizontal measure- ment.
Leica DISTO TM E7400x 788480a 15 EN Measuring Functions Memory (20 last displays) Delete Memory 8.294 m 20 20 last displ ays are displayed. 1 8.294 m 20 Navigates trough 20 last displays. 2 The value from the main line can be used for fur- ther calculations.
Leica DISTO TM E7400x 788480a 16 EN Calibration Calibration of tilt se nsor (Tilt Calibration) 1 2 sec simultane- ously 2 Place device on absolutely flat s urface. 3 180° 4 Turn the device ho rizontally by 180° and place it again on absolutely flat surface.
Leica DISTO TM E7400x 788480a 17 EN Technical Data * applies for 100 % target refl ectivity (white painted wall), low background illumination, 25 ºC ** applies for 10 to 500 % target reflectivity, hi gh background illumination, - 10 ºC to + 50 ºC *** Tolerances apply from 0.
Leica DISTO TM E7400x 788480a 18 EN Message Codes If the message Error does not disappear after switching on the device repeatedly, contact the dealer. If the message InFo appears with a number, press the Clear button and observe the following instructions: Care • Clean the device with a damp, soft cloth.
Leica DISTO TM E7400x 788480a 19 EN Safety Instructions Permitted use • Measuring distances • Tilt measurement Prohibited use • Using the product without instruction • Using outside the stated.
Leica DISTO TM E7400x 788480a 20 EN Safety Instructions FCC statement (a pplicable in U.S.) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reason- able protection against harmful interference in a residential installation.
Leica Geosystems AG CH-9435 Heerbrugg (Switzerland) www.disto.com Leica Geosystems AG, He erbrugg, Swit zerland has been certified as being equipped with a quality system which meets the International Standards of Quality Management and Quality Syst em s (ISO standard 9001) and Environ- mental Management Systems (ISO standard 14 001).
An important point after buying a device Leica 788472 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Leica 788472 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Leica 788472 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Leica 788472 you will learn all the available features of the product, as well as information on its operation. The information that you get Leica 788472 will certainly help you make a decision on the purchase.
If you already are a holder of Leica 788472, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Leica 788472.
However, one of the most important roles played by the user manual is to help in solving problems with Leica 788472. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Leica 788472 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
