Instruction/ maintenance manual of the product LDCS 91 Legacy Car Audio
Go to page of 28
DVD/VCD/CD/MP3 PLA YER WITH AUTO REVERSE CASSETTE WITH AM/FM-STEREO DIGIT AL PLL TUNING RADIO WITH ANTI-THEFT FLIP DOWN DET ACHABLE P ANEL OWNER'S MANUAL Mobile V ideo System ENTER MENU 5 1 6 9 2 7 0 8 +10 34 A/P VOL F .
CONTENTS 1 Safety Information ........................................................................................ 2 Disc Notes ..................................................................................................... 3 T ape Notes ...
SAFETY INFORMA TION 2 CAUTION : THIS DVD PLA YER IS A CLASS I LASER PRODUCT . HOWEVER THIS DVD PLA YER USES A VISIBLE/INVISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIA TION EXPOSURE IF DIRECTED. BE SURE TO OPERA TE THE DVD PLA YER CORRECTL Y AS INSTRUCTED.
Disc formats supported by this player DVD 12 cm disc (Single-sided disc only) Video CD 12 cm disc CD 12 cm disc MP3 12 cm disc Discs which cannot be played with this player • DVD-ROM • DVD-R/DVD-RAM • CDV • CD-G Handling and Cleaning • Dirt, dust, scratches and warping disc will cause misoperation.
1. T ake care of your tape cassette to pr eserve the quality of the recor dings. Do not allow them to be exposed to direct sunlight. Stor e them in a place protected fr om dirt and dust and avoid handing with greasy or oily hands. Also, keep the away from magnets, and motors of the permanent magnet type.
INST ALLA TION NOTES: Choose the mounting location where the unit will not interfer e with the normal driving function of the driver . Before finally installing the unit, connect the wiring temporarily and make sur e it is all connected up properly and the unit and the system work pr operly .
1. Install brackets and screws r emoved from your old radio (not pr ovided with this unit). 2. Slide unit and frame into dash opening. 3. T rim ring has precutgr ooves on the back of it. The size of the trim ring can be reduced (made smaller) for dif ferent types of installations.
7 CAUTION: DO NOT INST ALL THE DET ACHABLE P ANEL BEFORE CONNECTING THE WIRE. 1. The unit is designed for negative terminal of the battery which is connected to the vehicle metal.
8 ELECTRIC CONNECTION FRONT RCA OUTPUT V . OUT = VIDEO OUT FL OUT = FRONT LEFT AUDIO OUT FR OUT = FRONT RIGHT AUDIO OUT REAR RCA OUTPUT V . OUT = VIDEO OUT RL OUT = REAR LEFT AUDIO OUT RR OUT = REAR RIGHT AUDIO OUT AUXILIAR Y IN V . IN = VIDEO IN L. IN = LEFT AUDIO IN R.
1. CLK Press it to change the display to clock display . 2. MODE Press it to change between radio or disc mode. 3. SETUP Display the SETUP menu. 4. OSD (BAND) Display statistical disc information during playback (T o change the band in radio stations) 5.
Preparing the Remote Contr ol Inserting the Batteries 1. Open the battery compartment cover . 2. Insert the new batteries.Make sur e that the positive and negative terminals of the batteries are oriented indicated.
11 BASIC OPERA TION CAR DVD/VCD/CD/MP3 CASSETTE RECEIVE ST T APE IN 1 16 5 19 13 17 20 4 11 10 9 12 15 14 8 7 6 3 18 2 26 24 25 23 21 22.
12 BASIC OPERA TION 1. OPEN BUTTON Press it to flip down the fr ont panel then you can insert the T APE into the tape compartment. 2-3. VOL +/ VOL- & SEL BUTTON Press it to change audio mode thr ough volume, bass, treble, balance, and fader modes.
13 BASIC OPERA TION a. Continuously repeat at the curr ent chapter/track, when selected REP-ONE mode. b. Select REP-ALL mode to continuously repeat all chapter/track on the curr ent disc. c. REPEA T feature does not support VCD2.0 (with PBC ON). E. Pr ess 3/INT button to scan disc.
14 BASIC OPERA TION 17. / BUTTONS A. When long pressing the / button (mor e than 2 seconds) during play , the speed of rapid forward/reverse changes according to the disc as follow . DVD: VCD /CD: Normal Playback 2X 4X 6X 8X Normal Playback 2X 3X 4X MP3: Normal Playback 2X 4X B.
15 BASIC OPERA TION 24. FLASHING LED If the front panel is not on the main unit, LED will be flashing. 25. RESET BUTTON RESET button is placed on the housing and must be activated with either a ballpoint pen or thin metal object. The RESET button is to be activated for the following reasons: A.
16 BASIC OPERA TION c. Press OSD for the third time: T :01/18 P: 00:00:25 LR DISC TOT AL ELAPSED d. Press OSD for the fourth time: T :01/18 P: 00:00:25 LR DISC TOT AL REMAIN e. Press OSD for the fifth time: The message on the screen will be cleared for SVCD and VCD.
BASIC OPERA TION 17 Multi-subtitle Language Function (For DVD only) Press SUBTITLE during playback. Each time the button is pressed, number of the subtitle language changes in sequential order . Notes: The language number is differ ent according to the disc.
V ideo Material Normal TV Screen Pan Scan Letter-box 4:3 Wide (16:9) 4:3 16:9 GENERAL SETUP SPEAKER SETUP AUDIO SETUP PREFERENCES EXIT SETUP TV DISPLA Y PIC MODE ANGLE MARK OSD LANG CAPTIONS SCR SA VER MAIN P AGE NORMAL/PS NORMAL/LB WIDE 18 SETUP INITIAL SETUP --- MAIN P AGE--- 1.
--- GENERAL P AGE --- 2. PIC MODE SETUP Select AUTO, the player PIC mode will depend on DVD disc. Select HI-RES format for best image resolution. Select N-FLICKER format on format on image or picture under noise af fect.
--- GENERAL P AGE --- SCR SA VER SETUP Select the SCR SA VER output ON/OFF . SPEAKER SETUP --- SPEAKER SETUP P AGE --- This is to activate the audio output from DOLBY AC3 5.1 DOWNMIX to 2 channel mode. Select the preferred SPEAKER connection by using the cursor buttons.
SETUP PREFERENCES SETUP --- PREFERENCES P AGE --- 1. TV TYPE SETUP This player can play discs recor ded in either P AL or NTSC format. Select NTSC format, when you connected to NTSC TV . Select P AL format, when you connected to P AL TV . Select AUTO format, the player TV output format will according to the DVD disc format.
--- PREFERENCES P AGE --- 3. SUBTITLE LANGUAGE SETUP Select the preferr ed SUBTITLE language by using the cursor buttons. --- PREFERENCES P AGE --- 4. DISC MENU LANGUAGE SETUP Select the preferr ed DISC MENU language by using the cursor buttons. --- PREFERENCES P AGE --- 5.
General Setup TV Display Normal/PS PIC Mode AUTO Angle Mark ON OSD Language English Captions OFF SCR Saver OFF Speaker Setup Downmix Stereo Audio Setup Audio Out Analog OP Mode Line Out Dynamic LPCM O.
24 SPECIFICA TIONS Supply voltage : 12V DC (11V -15V) Current consumption : Less than 10A Signal system : Compositive video 1.0Vp-p 75 Ω Discs played : (1) DVD-VIDEO disc 5”(12 cm) single-sided, s.
This product incorporates copyright pr otection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners.
.
88-V2940-01.
An important point after buying a device Legacy Car Audio LDCS 91 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Legacy Car Audio LDCS 91 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Legacy Car Audio LDCS 91 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Legacy Car Audio LDCS 91 you will learn all the available features of the product, as well as information on its operation. The information that you get Legacy Car Audio LDCS 91 will certainly help you make a decision on the purchase.
If you already are a holder of Legacy Car Audio LDCS 91, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Legacy Car Audio LDCS 91.
However, one of the most important roles played by the user manual is to help in solving problems with Legacy Car Audio LDCS 91. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Legacy Car Audio LDCS 91 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center