Instruction/ maintenance manual of the product OPTIDRIVE OPTIX-10OPTIX-10 Lanzar
Go to page of 18
www .lanzar .com 10-Channel Active Electronic Crossover Network with Subwoofer Level Control user’s manual OptiX -1 0 OptiX -1 0.
Congratulations on your purchase of a new Lanzar Opti signal processor . Opti mobile electronics are some of the most advanced car audio products available. These quality audio products are designed and engineered to afford you years of uncompromising musical service.
general features precautions features and specifications system wiring mounting and installation noise check and system adjustment troubleshooting 2 3 4-6 7-11 12-13 14 15 table of contents.
10 Crossover Channels Blue Light Illumination 4 Channel Inputs Signal Pass-through for Additional Processors Remote Bass Level Control High Channels: Separate Front and Rear Frequency and Gain Control.
3 Precautions T o prevent short circuits, be sure to disconnect the negative battery ground lead before wiring the system up. When you finish the installation, be sure to make one more check to be sure everything is done correctly . Reinstate all car parts that were removed.
4 featur es and specifications.
5 featur es and specifications 1. F/R INPUT SWITCH 2. FRONT & REAR CHANNEL MID CUT Q SELECTORS 3. FRONT & REAR CHANNEL MID CUT CONTROLS 4. Front & Rear Channel High-Pass Phase Inverters 5. Front Frequency & Gain Controls 6. Rear Frequency & Gain Controls 7.
6 featur es and specifications Crossover Frequencies -Front High-Pass -Front Mid High-Pass -Front Mid Low-Pass -Rear High-Pass -Rear Mid High-Pass -Rear Mid Low-Pass Crossover Slope Rate Subwoofer Boost Boost Frequency Mid Cut Mid Cut Q: Distortion Frequency Response Signal-to-Noise Ratio (A) Separation Power Source Dimensions 1.
7 System wiring 2-CHANNEL 3 WA Y SYSTEM REAR CHANNEL Speakers FRONT CHANNEL Speakers Head unit (Stereo, DVD Player , T ape Deck, etc.) TO REAR OUTPUT TO SUB OUTPUT to REMOTE OUTPUT from HEAD UNIT BA T.
8 System wiring 2-CHANNEL MUL TIPLE CROSSOVER SYSTEM TO REAR MID OUT TO SUB OUTPUT Head unit (Stereo, DVD Player , T ape Deck, etc.) SUBWOOFER Speakers REAR MID-WOOFER Speakers TO FRONT MID OUT TO REA.
9 TO SUB OUTPUT TWEETER Speakers SUBWOOFER Speakers TO FRONT MID OUT TO REAR HIGH OUT TO FRONT HIGH OUT GROUND BA TTERY MID-WOOFER Speakers WOOFER Speakers UPPER MIDRANGE Speakers (to REMOTE OUTPUT fr.
10 System wiring BA TTERY TO FRONT HIGH OUT 4 CHANNEL 4 WA Y SYSTEM TO REAR MID OUT TO SUB OUTPUT to REMOTE OUTPUT from HEAD UNIT GROUND SUBWOOFER Speakers FRONT TWEETER Speakers REAR MID-WOOFER Speak.
11 System wiring 6-CHANNEL 5-WA Y SYSTEM FRONT TWEETER Speakers TO REAR MID OUT TO SUB OUTPUT Head unit (Stereo, DVD Player , T ape Deck, etc.) to REMOTE OUTPUT from HEAD UNIT SUBWOOFER Speakers FRONT.
12 Mounting and installation Y our new Opti Series crossover comes complete with all required mounting hardware. Please read the Installation Precautions section below before installing your Lanzar Op.
13 Mounting and installation • Solder -less connectors or soldering gun with heat shrink tubing 1. Find a suitable location in the vehicle to mount the processor . The X-10 is a trunk mount unit and it should be installed in close proximity to your amplifier system on the amp rack.
NOISE CHECK Check the entire audio system for noise before permanently securing the CROSSOVER mounting 1. Start the engine. 2. T urn the audio system on. 3. Rev the engine and vary the VOLUME of the audio system to determine if there is any unwanted noise.
1. There is an audible distortion at a low volume level. PROBLEM POSSIBLE CAUSE • Output levels NOT set correctly . • Crossover frequencies NOT set correctly . • Check for shorts on the speaker leads. 2. A whining sound can be heard through the speakers when the audio system is at low volume with the engine running.
All Lanzar Signal Processors are carefully constructed and thoroughly tested before shipment. Units purchased in the USA are warranted to be free of defects in material and workmanship for three (3) years from the date of purchase. This warranty is limited to the original retail purchaser of the Signal Processor .
An important point after buying a device Lanzar OPTIDRIVE OPTIX-10OPTIX-10 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Lanzar OPTIDRIVE OPTIX-10OPTIX-10 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Lanzar OPTIDRIVE OPTIX-10OPTIX-10 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Lanzar OPTIDRIVE OPTIX-10OPTIX-10 you will learn all the available features of the product, as well as information on its operation. The information that you get Lanzar OPTIDRIVE OPTIX-10OPTIX-10 will certainly help you make a decision on the purchase.
If you already are a holder of Lanzar OPTIDRIVE OPTIX-10OPTIX-10, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Lanzar OPTIDRIVE OPTIX-10OPTIX-10.
However, one of the most important roles played by the user manual is to help in solving problems with Lanzar OPTIDRIVE OPTIX-10OPTIX-10. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Lanzar OPTIDRIVE OPTIX-10OPTIX-10 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
