Instruction/ maintenance manual of the product OPTI Drive OPTIX3B Lanzar
Go to page of 12
www .lanzar .com user’s manual OptiX-3B OptiX-3B 3-Way Electronic Crossover Network w/Remote Bass Boost and Level Control.
Congratulations on your purchase of a new Lanzar Opti signal processor . Opti mobile electronics are some of the most advanced car audio products available. These quality audio products are designed and engineered to afford you years of uncompromising musical service.
general features precautions features and specifications system wiring mounting and installation noise check and system adjustment troubleshooting 2 3 4-5 6 7 8 9 table of contents.
2 general featur es Blue light illuminated control panel Rotary control knobs 12dB per octave crossover slopes PWM power supply Remote bass boost (0-+18dB) and level controls Subwoofer mode switch Var.
3 Precautions T o prevent short circuits, be sure to disconnect the negative battery ground lead before wiring the system up. When you finish the installation, be sure to make one more check to be sure everything is done correctly . Reinstate all car parts that were removed.
4 featur es and specifications.
5 featur es and specifications Adjustable Bass Boost Frequency Adjustable Bass Boost Adjustable Q Control Selectable Crossover Frequency -High Pass -Mid High Pass -Mid Low Pass -Subwoofer (Low Pass) P.
6 System wiring Subwoofer mode switch: allows sub-woofer mode channel to receive signal from either , the mix of from front inputs, the direct from rear inputs.
7 Mounting and installation Y our new Opti Series Crossover comes complete with all required mounting hardware. Mark the location for the mounting screw holes by positioning the Crossover where you wish to install it and use a scribe (or one of the mounting screws) inserted in each of the mounting holes to mark the mounting surface.
8 Noise check and system adjustment NOISE CHECK Check the entire audio system for noise before permanently securing the CROSSOVER mounting 1. Start the engine. 2. T urn the audio system on. 3. Rev the engine and vary the VOLUME of the audio system to determine if there is any unwanted noise.
1. There is an audible distortion at a low volume level. PROBLEM POSSIBLE CAUSE • Output levels NOT set correctly . • Crossover frequencies NOT set correctly . • Check for shorts on the speaker leads. 2. A whining sound can be heard through the speakers when the audio system is at low volume with the engine running.
All Lanzar Signal Processors are carefully constructed and thoroughly tested before shipment. Units purchased in the USA are warranted to be free of defects in material and workmanship for three (3) years from the date of purchase. This warranty is limited to the original retail purchaser of the Signal Processor .
An important point after buying a device Lanzar Lanzar OPTI Drive OPTIX3B (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Lanzar Lanzar OPTI Drive OPTIX3B yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Lanzar Lanzar OPTI Drive OPTIX3B - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Lanzar Lanzar OPTI Drive OPTIX3B you will learn all the available features of the product, as well as information on its operation. The information that you get Lanzar Lanzar OPTI Drive OPTIX3B will certainly help you make a decision on the purchase.
If you already are a holder of Lanzar Lanzar OPTI Drive OPTIX3B, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Lanzar Lanzar OPTI Drive OPTIX3B.
However, one of the most important roles played by the user manual is to help in solving problems with Lanzar Lanzar OPTI Drive OPTIX3B. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Lanzar Lanzar OPTI Drive OPTIX3B along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
