Instruction/ maintenance manual of the product HTG447 Lanzar
Go to page of 23
.
< 3 > INTRODUCTION HERTIAGE amplifiers pr ovide high-per formance sound r einfor cement for y our mobile audio equipment. Its versatility enables compatibility with optional Equalizers , F requency Dividing Crossover Netw orks, and other audio pr ocessors in a customized syst em.
< 4 > T ABLE OF C ONTENT S PLANNING Y OUR SYSTEM ................................................................. WIRING C ONNECTION ........................................................................ P ANEL LA Y OUT ......................
< 5 > C ONNECTING THE POWER CA UTION: AS A PRECA UTION, DISCONNECT THE POWER WIRE FROM THE BA T TER Y WHILE MAKING THE POWER AND GROUND CONNECTIONS TO THE AMPLIFIER. 4/8 GA UGE ( Thicker if planning for additional Amplifiers) wire is recommended f or both the power and gr ound wires 12 Gauge, for the r emote turn-on wire 16 Gauge.
< 6 > P ANEL LA Y OUT HTG237 / HTG257 FRONT VIEW HTG2100D FRONT VIEW HTG447 FRONT VIEW 1 9 2 3 5 5 6 7 8 1 9 2 4 4 6 8 1 1 2 2 4 4 4 4 6 6 8 HTG157 FRONT VIEW 19 2 6 8 43.
< 7 > P ANEL LA Y OUT HTG237 / HTG257 REAR VIEW HTG2100D REAR VIEW HTG447 REAR VIEW 10 11 12 13 14 10 11 12 13 10 11 12 13 14 14 HTG157 REAR VIEW 10 11 12 13 14.
< 8 > C ONTROL FUNC TIONS 1. RCA input jacks These RCA input jacks are for use with sour ce units that hav e RCA or Line level outputs. A source unit with a minimum level of 200mV is r equired for proper operation. The use of high quality twisted pair cables is recommended to decrease the possibility of radiated noise entering the syst em.
< 9 > C ONTROL FUNCTIONS 8. LED Will illuminate GREEN to indicate the amplifier is on and oper ating normally , and will be illuminated RED if the amplifier shuts down due to short circuit, DC offset, or overheating det ec ted by on board prot ection circuitr y 9.
< 10 > 2-4 Syst em Diagrams MONO Channel System Design #1 HT G2100D HTG157 2-4.
< 11 > Syst em Diagrams 2Channel System Design #1 HT G237 / HT G257.
< 12 > Syst em Diagrams 2Channel System Design #2 HT G237 / HT G257.
< 13 > Syst em Diagrams 2Channel System Design #3 HT G237 / HT G257.
< 14 > Syst em Diagrams 4Channel System Design #1 HT G447.
< 15 > Syst em Diagrams 4Channel System Design #2 HT G447.
< 16 > Syst em Diagrams 4Channel System Design #3 HT G447 1CH 4-8 Ohms WOOFER 4-8ohms WOOFER 4-8ohms 2CH 4-8 Ohms 3CH 4-8 Ohms 4CH 4-8 Ohms.
< 17 > TROUBLE SHOO TING GUIDE SYMPT OMS CHECK POINTS CURE NO SOUND Is the power LED illuminated? Check fuses in amplifier . Be sure T urn-on lead is connected AMP NO T SWIT CHING ON No power t.
< 19 > W ARNINGS Investigate the lay out of your automobile thoroughly before drilling or cutting any holes. T ak e care when to work near the gas tanks , lines, or hy draulic lines , and electrical wiring. D on't use power amplifier unmounted .
< 14 > Syst em Diagrams 4Channel System Design #1 HT G447.
< 15 > Syst em Diagrams 4Channel System Design #2 HT G447.
< 16 > Syst em Diagrams 4Channel System Design #3 HT G447 1CH 4-8 Ohms WOOFER 4-8ohms WOOFER 4-8ohms 2CH 4-8 Ohms 3CH 4-8 Ohms 4CH 4-8 Ohms.
< 17 > TROUBLE SHOO TING GUIDE SYMPT OMS CHECK POINTS CURE NO SOUND Is the power LED illuminated? Check fuses in amplifier . Be sure T urn-on lead is connected AMP NO T SWIT CHING ON No power t.
< 18 > SPECIFICA TIONS HTG237 HTG257 HTG447 HTG2100D MAXIM UM POW ER OUTPUT 1000 000W 2000W 2400W POW ER OUTPUT RMS @4Oh CH X 125 CH X 500W 4CH X 250W 1CH X 350W POW ER OUTPUT RMS @2Oh CH X 225 CH X 650W 4CH X 350W 1CH X 800W POW ER OUTPUT RMS @1Oh ON ON CH X 1200W BRIDGED POW ER MAX @4 Oh CH X 1000 CH X 2000W ONE TH 0 D.
< 19 > W ARNINGS Investigate the lay out of your automobile thoroughly before drilling or cutting any holes. T ak e care when to work near the gas tanks , lines, or hy draulic lines , and electrical wiring. D on't use power amplifier unmounted .
An important point after buying a device Lanzar HTG447 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Lanzar HTG447 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Lanzar HTG447 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Lanzar HTG447 you will learn all the available features of the product, as well as information on its operation. The information that you get Lanzar HTG447 will certainly help you make a decision on the purchase.
If you already are a holder of Lanzar HTG447, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Lanzar HTG447.
However, one of the most important roles played by the user manual is to help in solving problems with Lanzar HTG447. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Lanzar HTG447 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
