Instruction/ maintenance manual of the product MS6 SERIES AB Soft
Go to page of 14
Opal Pro to Mod TCP Page 1 Opal Pro MS6 SER IES AB Ethernet I P Interface Users Manual Revision 1.00.
Opal Pro to Mod TCP Page 2.
Opal Pro to Mod TCP Page 3 FOR YOUR SAFETY Only qualified personnel shoul d install this equipment, after first reading and understanding all the information in this manual.
Opal Pro to Mod TCP Page 4.
Opal Pro to Mod TCP Page 5 Table of Conten ts INTRODUCTION .............................................................................................. 6 HARDWARE ......................................................................................
Opal Pro to Mod TCP Page 6 Opal Pro to Mod TC P Introduction The Opal Pro can be m onitored and controlled over an Ethernet communication network using the AB Ethernet IP pr otocol. The Opal Pro connects to the Ether net network through and optional Ethernet card that is mounted on the m ain Opal Pro control car d (CA530).
Opal Pro to Mod TCP Page 7 LED Indicators Two bi-colour (red/green) LED indicators are mount ed beside the network connector. The upper LED indicates the Ethernet interface card stat us.
Opal Pro to Mod TCP Page 8 Op al Pro Paramete r Settings The parameters in t he Opal Pro used to con figure the Ehernet inter face card (group 14) ar e only accessible if a Ethernet interface card is inst alled. The parameter sett ings are as follows: Opal Pro Parameter Setting Description 2.
Opal Pro to Mod TCP Page 9 15.04 Comm Fault Enable Disable Enable – Opal Pro trips out on a communication fault Disable – Nothing happens on a communication fault 15.05 Comm Fault Time 0.1 to 5.0 secs This is the time sett ing that the Opal Pro uses to detect a communication fault.
Opal Pro to Mod TCP Page 10 I/O Configuration The Opal Pro supports 4 input words and 51 output words. Their description is as follows: Input Words (Polled) AB Ethernet IP Name Description Bit 0 – R.
Opal Pro to Mod TCP Page 11 Output Words (Polled) AB Ethernet IP Name Description Bit 0 – Ready to Run (dr ive is enable and has 3 phase power) Bit 1 –Running (start is regulating) Bit 2 – Full On (star ter is phased fully on) Bit 3 – Up to Speed (st arted is phased fully on and the curr ent is below 105% of nameplate cur rent as set in 13.
Opal Pro to Mod TCP Page 12 Relay Status Status of the Relay O utputs Bit 0 – Running Bit 1 – By-Pass Bit 2 – Shorted SCR Bit 3 – Reverse 1.07 Input Word 9 Bit 4 – Faulted 1.08 Input Word 10 Analog Output Analog Output value in Volts X 100 2.
Opal Pro to Mod TCP Page 13 12.01 Input Word 27 Analog Output 16 = Current Refer ence 17 = Current Feedback 18 = Overload level 19 = Phase Angle 13.01 Input Word 28 Motor Amps Motor nameplate cur rent in Amps 13.02 Input Word 29 Motor Volts Motor nameplat e volts in Volts 13.
Opal Pro to Mod TCP Page 14 NOTE: The Opal Pro must have firmw are version 1.70 or higher..
An important point after buying a device AB Soft MS6 SERIES (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought AB Soft MS6 SERIES yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data AB Soft MS6 SERIES - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, AB Soft MS6 SERIES you will learn all the available features of the product, as well as information on its operation. The information that you get AB Soft MS6 SERIES will certainly help you make a decision on the purchase.
If you already are a holder of AB Soft MS6 SERIES, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime AB Soft MS6 SERIES.
However, one of the most important roles played by the user manual is to help in solving problems with AB Soft MS6 SERIES. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device AB Soft MS6 SERIES along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
