Instruction/ maintenance manual of the product WS2813UIT La Crosse Technology
Go to page of 31
WS‐2813U‐IT WirelessProfessional WeatherCenter OperationsManual Revision: 5 .
Page | 2 TABLE OF CONTENTS TABLE OF CONTENTS……………………………… ……………………………… …….……………...2 INTRODUCTION……………………… ………………………………………… …………….
Page | 3 The following Weather Alarms can be adjusted in ALARM set mode… ………..…20 Default Weather Alarm values…………………………………………… ………….
Page | 4 ongratulations on purchasing this state ‐ of ‐ the ‐ art weather station. Featuring time, date, weather forecast, w.
Page | 5 INVENTORY OF CONTENTS Carefully open the package and check that the following contents are complete: Wind .
Page | 6 FEATURES: WIRELESS DISPLAY Time display in 12/24 hour time format Automatic time and date (PC tim.
Page | 7 100% solar ‐ powered with built ‐ in rechargeable alkaline power cell (not replaceable).
Page | 8 5. Setup troubleshooting: If the sensor data fails to display for any of the outdoor sensors within 10.
Page | 9 or the sensors closer and wait a few minutes to see if the wireless icons display again.
Page | 10 Position the display station to receive data from the thermo ‐ hygro sensor and send data to the USBTR.
Page | 11 Stop the weather alarm when ringing MIN/MAX KEY Press to display minimum and maximum record s of .
Page | 12 MANUAL SETTINGS: Press and hold the SET key for 3 seconds to enter the SET mode.
Page | 13 4. Press the ▲ UP ARROW key or ▼ DOWN ARROW key to set the minute. 5. Press the SET key to confirm and to enter the 12/24 ‐ HOUR TIME DISPLAY SETTING .
Page | 14 1. Press the ▲ UP ARROW key or ▼ DOWN ARROW key to toggle between the unit “mph”, “km/h”, "bft", "knots" or “m/s” 2.
Page | 15 .06, .09, or .12 inHg (2, 3 or 4 hPa). Select lower values (.06) for high humidity areas like the coastline. Select high numbers (.
Page | 16 FACTORY RESET PROCEDURE WARNING: Performing a factory reset will erase all MIN/MAX values and weather .
Page | 17 The Weather alarms can be set when certain weather conditions are met according to the requirements.
Page | 18 PRESSURE ALARMS 1. In the normal display mode, press the ALARM key once. The high ‐ pressure alarm display will be shown. 2. Press and hold the SET key for about 2 seconds.
Page | 19 2. Press and hold the SET key for about 2 seconds. The humidity digit will flash. 3. Press the ▲ UP ARROW key or ▼ DOWN ARROW key to set the high indoor humidity alarm value.
Page | 20 5. Press the SET key to switch the alarm on or off. The ((( ))) icon indicates the alarm is switched on. 6. Press the ALARM key once.
Page | 21 24 HOUR RAINFALL ALARM 1. The 24 ‐ hour rainfall alarm display will be shown. 2. Press and hold the SET key for about 2 seconds. The 24 ‐ hour rainfall digit will flash.
Page | 22 Every time a new average pressure value has been obtained (once per minute), this value is compared with an internal reference value.
Page | 23 last noticeable change in the weather was when it was sunny (the sun icon only).
Page | 24 Press the SET key to toggle between Mode1 and Mode 2 of the display.
Page | 25 TOTAL RAINFA LL AMOUNT The total rainfall measurement is displayed in the unit of mm or inch. It shows the total rainfall accumulated since last reset of the total rainfall amount.
Page | 26 (“OF.L” displayed if outside this range) INDOOR HUMIDITY 1% to 99% with 1% resolution (“ .
Page | 27 RAINFALL 0" to 393.7" with 0.01 inch resolution 0 to 9999 mm with 0.1 mm resolution (displays "OF.L" when > 393.
Page | 28 RAIN SENSOR 2 x AA size batteries (IEC LR6, 1.5V) WIND SENSOR Solar powered BATTERY LIFE Approxi.
Page | 29 manufacturer. FCC STATEMENT Statement according to FCC part 15.19: This device complies with part 15 of the FCC rules.
Page | 30 WARRANTY INFORMATIO N La Crosse Technology, Ltd provides a 1 ‐ year limited warranty on this product against manufacturing defects in materials and workmanship.
Page | 31 La Crosse Technology, Ltd 2817 Losey Blvd. S. La Crosse, WI 54601 Customer Support: www.lacrossetechnology.com/support For more information: www.
An important point after buying a device La Crosse Technology WS2813UIT (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought La Crosse Technology WS2813UIT yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data La Crosse Technology WS2813UIT - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, La Crosse Technology WS2813UIT you will learn all the available features of the product, as well as information on its operation. The information that you get La Crosse Technology WS2813UIT will certainly help you make a decision on the purchase.
If you already are a holder of La Crosse Technology WS2813UIT, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime La Crosse Technology WS2813UIT.
However, one of the most important roles played by the user manual is to help in solving problems with La Crosse Technology WS2813UIT. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device La Crosse Technology WS2813UIT along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
