Instruction/ maintenance manual of the product WS-7034U La Crosse Technology
Go to page of 20
WS-7034U Wireless 433 MHz Temperature Station Instruction Manual.
2 TABLE OF CONTENTS Topic Page Quick Setup 3-5 Inventory of Contents 6-7 Detailed Setup Guide Battery Installation 8 Setting the Time 9-10 Selecting Units of Measurement 10 Features Minimum and Maximu.
3 QUICK SETUP Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries. 1. Have the indoor tem perature station and remote tem perature sensor 3 to 5 feet apart. 2. Batteries shoul d be out of both units for 10 minutes. 3. Place the batteries into the remote temperature sensor first then into the indoor tem perature station.
4 display will show both the indoor temperature and an outdoor temperature. If the indoor tem perature station does not display bot h temperat ures after the 10 minutes pl ease retry the set up as stated above.
5 Figure 2 Figure 1 Holder NOTE: Fog and mist will not harm your remote t emperature sensor but direct rain must be avoided. To complete the set up of your i ndoor temperature station after the 10 m inutes have passed please follow the steps on pages 8-9.
6 Battery Cover ADDITIONAL EQUIPMENT (not included) 1. 1 Philips screwdriver. 2. 2 Fresh AAA Alkaline batteries. 3. 2 Fresh AA Alkaline batteries DETAILED SETUP GUIDE Battery Installation 1. Install 2 AA batteries in the remote temperature sensor. Make sure they do not spring free, or start-up problems may occur.
7 Setting the Time 1. Press and hold the “ SET” button for 5 second, “12h” will appear in the TIME LCD. 2. Press and release the “ MIN/MAX” button to select either 12h time (am/pm) or 24h time 3. Press and release the “ SET” button 2 times, the hour will flash in the upper left corner.
8 If there is no display here it is AM. Make sure you set the time accordingly. Selecting Units of Measuremen t 1. Press and hold the “SET” button for 5 second until “12h” or “24h” appears in the TIME LCD. 2. Press and release the “ SET” button again, “ ° F” will appear in the TIME LCD.
9 2. The recorded minimum temperature is displayed. The time of the minimum outdoor temperature will also flash. 3. Press the “MIN/MAX” button, “MAX” appears next to the indoor and remote temperatures. 4. The recorded maximum temperature is displayed.
10 Adding Additional Remote Temperature Sensors (optional) The WS-7034U is able to receive signals from 3 different remote temperature sensors. Following are some brief instructions for the basic set-up of remote temperature sensor units with the WS-7034U.
11 indoor temperature station and do not press any buttons for ten minutes. Transmission problems will arise if this is not done correctly. To view the temperature of a different remote temperature sensor unit, press and release the “SET/CH” button.
12 Remote Temperature Sensor 1. Remove the mounting bracket from the remote temperature sensor. 2. Mount the bracket in the desired location with either screws or adhesive tape. 3. Reattach the remote temperature sensor into mounting bracket. Indoor Temperature Station The indoor temperature station comes with the table stand already mounted.
13 temperature station over the screw and pull down to secure. TROUBLESHOOTING NOTE: For problems not solved, please contact La Crosse Technology via e-mail or phone, or visit our website, www.lacrossetechnology.com Problem: The LCD is faint Solution: Replace batteries Problem: No outdoor temperature is displayed.
14 so the straight-line signal is not passing through more than two or three walls. Problem: Temperatures do not match if units are placed next to each other. Solution: Each temperature sensor is manufactured to be accurate to within 1 degree plus or minus and under normal conditions, so two sensors could be as much as 2 degrees different.
15 is difficult to compensate for the above factors and obtain an accurate comparison. MAINTENANCE AND CARE INSTRUCTIONS • Extreme temperatures, vibration, and shock should be avoided to prevent damage to the units. • Clean displays and units with a soft, damp cloth.
16 SPECIFICATIONS Transmitting Frequency 433MHz Measuring Temperatures Indoor Temperature Station 32 ° F to 156.2 ° F with 0.2 ° F resolution. (0 ° C to 69.0 ° C with 0.1 ° C resolution). Remote Temperature Sensor -21.8 ° F to 156.2 ° F with 0.
17 Sensor Indoor Temperature Station 2 x AAA, 1.5V Dimensions: (L x W x H) Indoor Temperature Station 2.36 x .88 x 5.90 in. (excluding table stand) (60 x 22.5 x 150 mm). Remote Temperature Sensor 2.32 x 0.86 x 2.55 in. (59 x 22 x 65 mm). Battery life Approximately 1 year.
18 This warranty does not cover any defects r esulting from im proper use, unauthorized repair s, faulty batteries, or the indoor tem perature stations inability to receive a signal due to any source of interference.
19 Phone: 608.782.1610 Fax: 608.796.1020 e-mail: support@lacrossetechnology.com (warranty work) sales@lacrossetechnology.com (information on other products) web: www.lacross ete chnology.com FCC DISCLAIMER This device complies with part 15 of the FCC rules.
20 FCC ID: OMO-01RX (Receiver), OMO-01TX (transmitter) THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1. THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND 2. THIS DEVICE MUST ACCEPT INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
An important point after buying a device La Crosse Technology WS-7034U (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought La Crosse Technology WS-7034U yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data La Crosse Technology WS-7034U - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, La Crosse Technology WS-7034U you will learn all the available features of the product, as well as information on its operation. The information that you get La Crosse Technology WS-7034U will certainly help you make a decision on the purchase.
If you already are a holder of La Crosse Technology WS-7034U, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime La Crosse Technology WS-7034U.
However, one of the most important roles played by the user manual is to help in solving problems with La Crosse Technology WS-7034U. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device La Crosse Technology WS-7034U along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
