Instruction/ maintenance manual of the product WS-1613-IT La Crosse Technology
Go to page of 10
PROFESSIONAL WEATHER CENTER WS-1613-IT Operation Manual IMPORTA NT: When a battery change is r equir ed on any of the units of this set, ALL units have to be reset and user must go through i ni tial set-up steps a gain.
6 Cable connection between the wind sensor and the thermo-hygro sens or Cable connection between the rain sensor and the thermo-hygro sensor Wireless tr ansmissio n at 915 MHz - thermo- hygro sensor t.
12 The Bonus Receiver use 2 x AA, IEC LR6, 1. 5V batteries. When th e batteries need to be replaced, the low battery symbol will appear on t he LCD. To install and replace the batt eries, please follow the steps b elow : 1. Remove the battery compartment cover.
18 CALENDA R SETT ING: The date default of the Weat her Center is 1. 1. of year 2005. The date can be set manually by proceeding as follo ws. 1. The year digit starts flashing . 2. Use the + or MI N/MAX key to set the year . The range runs from "00" ( 200 0) to "99" (2099).
24 2. Press and hold the SET key for about 2 seconds. Th e hour dig it of the alarm time will start fla shing. P ress the + or MIN/MAX key to set the hour of the alarm time. 3. Press the SET k ey to conf irm and advan ce to the minute setting. The minute digit will be flashing.
30 drops to +76.8°F (24.9 ° C) or below and ther eaf ter again increases to beyond +77°F (25 ° C), the data will be blink ing, but no alarm will be activate d. It has to drop to below +75.2°F (24 ° C) (with a pr e- set hysteresis of 1.8°F (1 ° C)) so that the alar m can b e produced again.
36 To view the weather history: 1. Press the HISTO RY key. The latest weather record will be show n with the date and time of recording. The "HIST O RY" icon will be displayed at the bott om of the LCD. 2. Press MIN/ MA X to view older records.
42 2. Press and hold the SET k ey for a bout 2 seconds, then the "RESET" icon wil l appear at the bottom part of the LCD. 3. Press the + key once, the n the st ored value will be reset to the current value and current time. 4. Press the ALARM key to return to no rmal dis play mode.
48 mounted using the screw or cable tie provided ont o a solid wall/ panel mast or mast to allow the wind to travel aroun d the sensor unhindered from all directions (ide al mast size should be from diam eter about 5 / 8 ” (16 mm) to 1 1 / 4 ” (33 mm)).
54 To wall m ount: 1. Fix a screw (not supplied) into the desired wall, leaving the head extended out the by about 5mm. 2. Hang the Bonus Receiver onto the screw.
An important point after buying a device La Crosse Technology WS-1613-IT (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought La Crosse Technology WS-1613-IT yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data La Crosse Technology WS-1613-IT - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, La Crosse Technology WS-1613-IT you will learn all the available features of the product, as well as information on its operation. The information that you get La Crosse Technology WS-1613-IT will certainly help you make a decision on the purchase.
If you already are a holder of La Crosse Technology WS-1613-IT, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime La Crosse Technology WS-1613-IT.
However, one of the most important roles played by the user manual is to help in solving problems with La Crosse Technology WS-1613-IT. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device La Crosse Technology WS-1613-IT along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
