Instruction/ maintenance manual of the product 10" Cabinet Saw Sliding Table Kuhn Rikon
Go to page of 20
10” Cabinet Saw Sliding T able Model: 10-1 10B/E Owner ’ s Manual For more information: www .rikontools.com or info@rikontools.com For Parts or Questions: techsupport@rikontools.com or 877-884-5167 Record the serial number and date of purchase in your manual for future reference.
IMPORT ANT! Safety is the single most important consideration in the operation of this equipment. The following in- structions must be followed at all times.
AL W A YS CHECK FOR DAMAGED P ARTS. Before initial or continual use of the tool, a guard or other part that is damaged should be checked to assure that it will operate properly and perform its intended function.
Safety W arnings........................................................................................................................................2 -3 T able Saw Safety Rules ......................................................................
5 Model 10-1 10B/E 10” T able Saw Sliding T able is shipped complete in 2 boxes. Unpacking and Checking Contents Separate all “loose parts” from packaging materials and check each item with “T able of Loose Parts” to make sure all items are accounted for , before discarding any packaging material.
6 T ABLE OF LOOSE P ARTS Item Part Name Qty A Swing Arm Assembly 1 B Swing Arm Extension Bar 1 C Sliding T able Carriage 1 D Sliding T able Support Arm 1 E Loose Parts Bag 1 Box #2 A B C D E.
7 Getting T o Know Y our Sliding T able 1. Flip Stop 2. Miter Fence 3. Sliding T able 4. Sliding T able Locking Pin 5. Push Block 6. Slide Handle 7. Swing Arm Assembly 8.
8 Mounting the Swing Arm Bracket 1. Open the motor cover located at the left side of the saw . 2. With assistance hold the swing arm bracket against the saw body and attach using four 8MM hex bolts, four 8MM washers and four 8MM hex nuts.
9 Mounting the Sliding T able Continued 3. Slide the hardware toward the cast mounting bracket located on the saw body . Place the adjusting plate on top of the set screws as shown (A,Fig.5). 4. T ighten the lock knob slightly , leaving loose for adjustment.
Carriage T able Support Arm Installation 1. Insert the support arm into the swing arm extension bar as shown (A, Fig. 9) making sure that bearing assembly rests between the adjusting nuts and the swing arm extension bar (B, Fig. 9). Reminder: T ighten the carriage bolts shown in Figure 8 on page nine once the support arm is installed.
11 Installing the Sliding T able Miter Fence 1. Locate the miter fence (A, Fig. 13) and miter fence locking knob (B, Fig. 13) as shown. 2. Lay the miter fence on top of the sliding table carriage and place the rotation shaft into the hole on the sliding table carriage.
12 Figure 17 Installing the Sliding T able Locking Pin 1. Locate the locking pin with the black handle and thread it through the sliding table body with wrench as shown.
13 Locking and Unlocking the Slide T able Keep the sliding table locked when not in use. Failure to do so could cause serious injury . T o lock the sliding table, pull the locking pin out- ward, twist and insert pin into the locking hole in the table carriage.
Cutting Sheet Goods 1. Adjust the hold down plate according to the width of material to be cut. 2. Lay the workpiece onto the table and up against the saw fence. 3. Slide the workpiece through the saw blade until the material engages the hold down plate.
15 BEFORE CLEANING OR CARR YING OUT MAINTENANCE WORK, DISCONNECT THE MACHINE FROM THE POWER SOURCE (W ALL SOCKET). NEVER USE W A TER OR OTHER LIQUIDS TO CLEAN THE MACHINE. USE A BRUSH. REGULAR MAINTENANCE OF THE MACHINE WILL PREVENT UNNECESSAR Y PROBLEMS.
16 FOR YOUR OWN SAFETY , AL W A YS TURN OFF AND UNPLUG THE MACHINE BEFORE CARR YING OUT ANY TROU- BLESHOOTING. For parts or technical questions contact: techsupport@rikontools.
17 Parts Diagram.
18 Parts List Key No . 1E 2E 3E 4E 5E 6E 7E 8E 9E 10E 11 E 12E 13E 14E 15E 16E 17E 18E 19E 20E 21E 22E 23E 24E 25E 26E 27E 28E 29E 30E 1F 2F 3F 4F 5F 6F 7F 8F 9F 10F 11 F 12F Part No.
19 2-Y ear Limited W arranty RIKON Power T ools/Richen Enterprise, Inc. (“Seller”) warrants to only the original retail consumer/purchaser of our products that each product be free from defects in materials and workmanship for a period of two (2) years from the date the product was purchased at retail.
For more information: 1 10 Cummings Park Woburn, MA 01801 877-884-5167/781-933-8400 techsupport@rikontools.com www .rikontools.com Copyright Richen Enterprise, Inc.
An important point after buying a device Kuhn Rikon 10" Cabinet Saw Sliding Table (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Kuhn Rikon 10" Cabinet Saw Sliding Table yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Kuhn Rikon 10" Cabinet Saw Sliding Table - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Kuhn Rikon 10" Cabinet Saw Sliding Table you will learn all the available features of the product, as well as information on its operation. The information that you get Kuhn Rikon 10" Cabinet Saw Sliding Table will certainly help you make a decision on the purchase.
If you already are a holder of Kuhn Rikon 10" Cabinet Saw Sliding Table, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Kuhn Rikon 10" Cabinet Saw Sliding Table.
However, one of the most important roles played by the user manual is to help in solving problems with Kuhn Rikon 10" Cabinet Saw Sliding Table. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Kuhn Rikon 10" Cabinet Saw Sliding Table along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
