Instruction/ maintenance manual of the product KS-220F/S-A KTI Networks
Go to page of 15
-12- Installation Guide 10/100 Bridging Converter KS-220F series DOC.991115-KS220F-K P/N: 750-0126-001 Model: KS-220F/T KS-220F/C KS-220F/S KS-220F/S-A KS-220F/S-3 KS-220F/S-5.
-15- 1999 KTI Networks Inc. All rights reserved. No part of this documentation may be reproduced in any form or by any means or used to make any directive work (such as translation or transforma- tion) without permission from KTI Networks Inc. KTI Networks Inc.
-13- The information contained in this document is subject to change without prior notice. Copyright KTI. All Rights Reserved. TRADEMARKS Ethernet is a registered trademark of Xerox Corp. WARNING: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
-14- T able of Contents Chapter 1 Introduction Introduction ............................................................................... 1 Features ................................................................................... 2 Specifications .
-1- 1. Introduction The 10/100 bridging converter provides two 10/100Mbps-based Fast Ethernet switch ports. Port 1 features one 10/100M UTP connection and Port 2 features either one 10/100M UTP connection or one 100M fiber connection.
-2- Features Complies with IEEE 802.3u 100BASE-TX 100BASE-FX and IEEE 802.3 10BASE-T specifications 2 switched ports: Port 1 - 10/100M TP port Port 2 - configurable 10/100M TP port or 100M Fib.
-3- Specifications Standard: 10BASE-T , 100BASE-TX, and 100BASE-FX Connectors: Port 1 - 2 RJ-45 jacks Port 2 - 2 RJ-45 jacks and 1 fiber connector Cables: 10BASE-T - Cat.
-4- 2. Installation Unpacking Check to see that you have everything before you start the installation. Installation guide The unit One AC power adapter for the switch Installation The switch can be placed on a desktop as a stand-alone unit.
-5- Checking AC Power One AC power adapter is contained in the product package. Before you begin the installation, check the AC voltage of your area. The AC power adapter which is used to supply the DC power for the unit should have the AC voltage matching the commercial power voltage in your area.
-6- 3. Making Network Connections T wo Switched Ports T wo switched ports are located on the front panel. Configuration Switches On rear panel, Port 1 and Port 2 have individual configuration switches as shown below: Port 1, Port 2 SW1 O f f Auto-negotiation is enabled.
-7- Important Note: If any change are made to the configuration switch settings, the power to the unit must be turned off and turned on again before the changes can take effect. The auto-negotiation mode enables the port to negotiate a common operation mode with the device connected at the remote end of the link cable.
-8- UTP Connections The following figure shows a UTP connection from TP port to another device via a straight-through UTP cable. When TP port of Port 2 is used, make sure Port 2 SW4 is set to OFF position.
-9- Fiber Port and Fiber Connection When connecting to a 100BASE-FX device using fiber cable, make sure Port 2 SW4 is set to ON position and TX-to-RX connection rule is followed. Since the fiber connector does not support auto-negotiation func- tion, it is recommended to set SW1 to ON position for the fiber connection.
-10- MUL TIMODE FIBER CABLE Connected device Duplex type Maximum length 100Base-FX NIC card Half-duplex 400 meters 100Base-FX NIC card Full-duplex 2K meters 100Base-FX hub port *1 Half-duplex 185 mete.
-11- 4. Interpreting LED Indicators The following figure shows the locations of the LED indicators: Power State Indication Interpretation On Normal The power of the unit is on. O f f Problem No power is being supplied to the unit. Link/Act. (Link/Activity) State Indication Interpretation On Normal An active link is established.
An important point after buying a device KTI Networks KS-220F/S-A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought KTI Networks KS-220F/S-A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data KTI Networks KS-220F/S-A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, KTI Networks KS-220F/S-A you will learn all the available features of the product, as well as information on its operation. The information that you get KTI Networks KS-220F/S-A will certainly help you make a decision on the purchase.
If you already are a holder of KTI Networks KS-220F/S-A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime KTI Networks KS-220F/S-A.
However, one of the most important roles played by the user manual is to help in solving problems with KTI Networks KS-220F/S-A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device KTI Networks KS-220F/S-A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
