Instruction/ maintenance manual of the product LM765s AOC
Go to page of 20
.
TABLE OF CONTENTS FOR YOUR SAFETY -------------------------------------------------- 1 SAFETY PRECAUTIONS -------------------------------------- 2 SPECIAL NOTES ON LCD MONITORS ------------------- 3 B.
Before operating the monitor, pleas e read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Pa rt 15 of the FCC Ru les.
PRECAUTIONS z Do not use the monitor near water, e.g. near a bathtub, w ashbowl, kitchen sink, laundry tub, sw imming pool or in a we t basement. z Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and c ause serious damage to the appliance.
SPECIAL NOTES ON LCD MONITORS The following symptoms are normal w ith LCD monitor and do not indicate a problem. NOTES • Due to the nature of the fluoresc ent light, the screen may flicker during initial use. Turn off the Power Sw it ch and then turn it on again to make sure the flicker disappears.
INSTALLATION INSTRUCTIONS SWIVEL BASE Install Remove Figure 1 Installing and Removing the Swivel Base POWER CORD Pow er Source: 1. Make sure that the power cord is the correct type required in y our area.
CONTROLS AND CONNECTORS VIDEO CABLE Connecting the D-Sub Cable: Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the co mputer’s D-Sub port. Connecting the Power Cord: Connect the power cord into your LCD monitor’s power input socket, and then plug the other end into a 3-pin AC power outlet.
ADJUSTING THE VIEWING ANGLE • For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’ s angle to your ow n preference. • Hold the stand so y ou do not t opple the monitor w hen you change the monitor’s angle.
OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the moni tor on or off. The other control buttons are located on the front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjus ted to your personal preferences.
FRONT PANEL CONTROL • Pow er Button: Press this button to turn the monitor ON or OFF. • Pow er Indicator: Blue — Power On mode. Orange — Off mode. • MENU / ENTER : Activate OSD menu when OSD is OFF or activate/de-activate adjustment function when OSD is ON or Exit OSD menu when in Brightness /Contrast Adjust OSD status.
HOW TO ADJUST A SETTING 1. Press the MENU-button to activate the OSD window . 2. Press - or + to navigate through the functions. Once the desired function is highlighted, press t he MENU-button to activate it. If the function selected has a sub-menu, press - or + again to navigate through the sub- menu functions.
ADJUSTING THE PICTURE The descriptions for function control LEDS Main Menu Item Main Menu Icon Sub Menu Item Sub Menu Icon Description Contrast Contrast from Digital-register. Luminance Brightness Backlight Adjustment Focus Adjust Picture Phase to reduce Horizontal-Line noise Image Setup Clock Adjust picture Clock to reduce Vertical-Line noise.
Main Menu Item Main Menu Icon Sub Menu Item Sub Menu Icon Description Yes N/A Auto Adjust the H/V Position, Focus and Clock of picture. Auto Config No N/A Do not execute Auto Config, return to main menu. H. Position Adjust the horizontal position of the OSD.
PLUG AND PLAY Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host sy stem of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities.
TECHNICAL SUPPORT (FAQ) Problem & Question Possible Solution Power LED is not on *Check if the Pow er Sw itch is in the ON position *Power Cord should be connected No Plug & Play *Check if the.
ERROR MESSAGE & POSSIBLE SOLUTION CABLE NOT CONNECTED : 1. Check that the signal-cable is pr operly connected , If the connector is loose, tighten the connector’s screws.
APPENDIX SPECIFICATIONS Driving system T FT Color LCD LCD Panel Size 43.2cm(17.0") Pixel pitch 0.264mm( H ) × 0.264mm( V ) Video R,G,B Analog Interface Input Separate Sy nc. H/V TT L H-Frequency 30kHz – 80kHz V-Frequency 55-75Hz Display Colors 16.
Switch • Auto Adjust Key • Volume • Volume • Power Button • MENU External Controls: Functions • Contrast • Brightness • Focus • Clock • H.
Preset Display Modes STANDARD RESOLUTION HORIZONTAL FREQUENCY VERTICAL FREQUENCY Dos-mode 720 x 400 31.47kHz 70.0Hz 640 × 480 31.47kHz 60.0Hz VGA 640 × 480 37.50kHz 75.0Hz 800 × 600 37.879kHz 60.0Hz SVGA 800 × 600 46.875kHz 75.0Hz 1024 × 768 48.363kHz 60.
CONNECTOR PIN ASSIGNMENT 15 6 10 11 15 15 - Pin Color Display Signal Cable PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1. Red 9. +5V 2. Green 10. Detect Cable 3. Blue 11. TXD 4. RXD 12. DDC-Serial Data 5. Ground 13. H-Sy nc 6. R-Ground 14. V-Sync 7. G-Ground 15.
An important point after buying a device AOC LM765s (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought AOC LM765s yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data AOC LM765s - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, AOC LM765s you will learn all the available features of the product, as well as information on its operation. The information that you get AOC LM765s will certainly help you make a decision on the purchase.
If you already are a holder of AOC LM765s, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime AOC LM765s.
However, one of the most important roles played by the user manual is to help in solving problems with AOC LM765s. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device AOC LM765s along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
