Instruction/ maintenance manual of the product KT6913 Kohler
Go to page of 20
Installation Guide Single-Control Bath and Shower T rim M product numbers ar e for Mexico (i.e. K-12345 M ) Los números de pr oductos seguidos de M corresponden a México (Ej.
T ools and Materials Before Y ou Begin CAUTION: Risk of product damage. Long screws, for installing trim, can damage the K-2971-KS valve. When using this valve and trim in a fiberglass or acrylic installation, use the 88526 Thin W all Installation Kit.
1. Install the Spout Remove the temporary nipple. Apply thread sealant and install a 1/2 ″ nipple so it extends 7/16 ″ (1.1 cm) beyond the finished wall. Apply a bead of plumbers putty or other sealant around the inlet end of the spout according to the manufactur er’s instructions.
2. Install the Showerhead NOTICE: Do not use thread sealant compound (pipe dope) on the shower arm threads. Instead, use thr ead sealant tape on the shower arm threads. This will avoid clogging the shower head spray outlets. Remove the temporary nipple from the shower elbow .
3. W ater T emperature Adjustment CAUTION: Risk of personal injury . T o eliminate the risk of scalding, the water temperature should never be set above 120°F (49°C). NOTE: Do not remove the O-ring and collar at this time. Removing the O-ring and collar will change the factory setting for the maximum water temperature.
4. Install the Faceplate and Handle Remove and discard the plaster guar d and/or dome, if installed. Rotate the valve stem fully counterclockwise to the ″ OFF ″ position. Install the faceplate onto the valve so the notch is to the bottom and secure with scr ews.
Guide d’installation Baignoire mono-contrôle et garniture de douche Outils et matériels A vant de commencer A TTENTION: Risque d’endommagement du produit. Les vis longues, pour l’installation de la garniture, peuvent endommager la valve K-2971-KS.
1. Installer le bec Retirer le mamelon temporair e. Appliquer un ruban d’étanchéité pour filetage et installer un mamelon de 1/2 ″ de manière à ce qu’il s’étende de 7/16 ″ (1.
2. Installer la pomme de douche A VIS: Ne pas utiliser de joint d’étanchéité pour filetage (colle à tuyau) sur les filetages de bras de douche. Utiliser du ruban d’étanchéité pour filetage sur les filetages de bras de douche à la place.
3. Réglage de la température d’eau A TTENTION: Risque de blessures corporelles. Pour éliminer les risques de brûlures, la températur e ne devrait pas être réglée au-dessus de 120°F (49°C). REMARQUE: Ne pas retir er le joint torique ou le collier pour le moment.
4. Installer le couvercle et la poignée Retirer et jeter le r enfort en plâtre et/ou dôme, s’il est installé. Pivoter la tige de la valve complètement vers la gauche à la position fermée ″ OFF ″ . Installer le couvercle sur la valve de manièr e à ce que l’encoche soit à la base et sécuriser avec des vis.
Guía de instalación Guarnición de grifería monomando de bañera y ducha Herramientas y materiales Antes de comenzar PRECAUCIÓN: Riesgo de daños al producto. Los tornillos largos, para instalar la guarnición, pueden dañar la válvula K-2971-KS.
1. Instale el surtidor Retire el niple pr ovisional. Aplique sellador de roscas e instale un niple de 1/2 ″ de modo que sobresalga 7/16 ″ (1,1 cm) de la par ed acabada. Aplique masilla de plomería u otro sellador alr ededor del extremo de entrada del surtidor , según las instrucciones del fabricante.
2. Instale la cabeza de ducha A VISO: No utilice compuesto sellador líquido de r oscas (pasta lubrificante) en las roscas del brazo de la ducha. En su lugar , aplique cinta selladora de roscas a las r oscas del brazo de ducha. Esto evitará que se tapen las salidas rociadoras de la cabeza de ducha.
3. Ajuste de la temperatura del agua PRECAUCIÓN: Riesgo de lesiones personales. Para eliminar el riesgo de quemaduras, la temperatura del agua nunca debe ajustarse a más de 120°F (49°C). NOT A: No retir e el arosello (O-ring) ni el collarín en este momento.
4. Instale la placa frontal y la manija Retire y deseche el pr otector de yeso y/o la cúpula, si están instalados. Gire la espiga de la válvula completamente a la izquier da, a la posición de cerrada. Instale la placa frontal sobr e la válvula, de manera que la muesca esté orientada hacia abajo, y fije con tornillos.
1 14487-2- CC.
1 14487-2- CC.
1 14487-2- CC.
USA/Canada: 1-800-4KOHLER México: 001-800-456-4537 kohler .com ©2010 Kohler Co. 1 14487-2-CC.
An important point after buying a device Kohler KT6913 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Kohler KT6913 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Kohler KT6913 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Kohler KT6913 you will learn all the available features of the product, as well as information on its operation. The information that you get Kohler KT6913 will certainly help you make a decision on the purchase.
If you already are a holder of Kohler KT6913, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Kohler KT6913.
However, one of the most important roles played by the user manual is to help in solving problems with Kohler KT6913. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Kohler KT6913 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
