Instruction/ maintenance manual of the product K-8709T Kohler
Go to page of 10
BEFORE YOU BEGIN · · · Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation sequences. Follow the sections that pertain to your particular installation . This will help you avoid costly mistakes.
1. REMOVE EXISTING TOILET T urn off water supply . flush the toilet and use a sponge to remove the remaining water from the tank and bowl. Disconnect the supply shut-off valve (if present) and remove the old tank and bowl.
-3- 3. SELECT P-TRAP OR S-TRAP to installation your toilet according to the drain and shut-off valve's Roughing-in dimensions. 2. ASSEMBLE T ANK BOL TS&W ASHERS Slip bolt heads into mounting plate on bottom of tank. Place large foam washer on base of flush valve.
-4- 4 Connect fill valve to water supply with hose only . 4 4. INST ALL THE TOILET & CONNECT W A TER SUPPL Y Place the toilet in its final location. Use plastic drill guide and 8mm drill bit to drill floor mounting holes for installation over concrete.
5.CHECK W A TER LEVEL T urn on water supply check for leaks. If necessary , adjust black float adjustment clip, and sliding float up or down on metal float rod until water level at marked water line . 5A 5. 5A 6. ADJUST OVERFLOW HEIGHT (If necessary) Adjust overflow tube so that the top is 20mm above the waterline.
-6- 7. CONNECT PUSH BUTTON Put large flange through hole in lid. Screw retaining ring onto flange. T urn the screw inside the push button flange to secure tank lid to flush valve assembly . Make certain that the flush valve assembly is adjusted high enough that the button touches the assembly .
-7- 8. Install seat with hardware provided. See Fig.#8. 8. 8 £ Fig. #8 8 1037406-T01-A.
SYMPTOMS PROBABLE CAUSES CORRECTIVE ACTION TROUBLESHOOTING CHART 1. Float valve turns on/off by itself without toilet being flushed 2. Float valve continues to run, allowing water to enter tank. 3. Incorrect water level height. 4. Long or noisy tank fill 5.
() () 138 19 200021 Plumbing Fixtures and Fittings Limited One-year W arranty Kohler plumbing fixtures and fittings are warranted to be free of manufacturing defects. This product is warranted for one year from date of purchase. Kohler China will be responsible for any problems caused by manufacturing defects provided with the invoice.
ODEON 1004136-** T ank Cover K-8741T-** Odeon Seat 1021449 Screw 1021447 Right Hand Hinge 1021446 Left Hand Hinge 1004139 Flush V alve Assy . 1004140 Flush Button Assy .
An important point after buying a device Kohler K-8709T (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Kohler K-8709T yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Kohler K-8709T - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Kohler K-8709T you will learn all the available features of the product, as well as information on its operation. The information that you get Kohler K-8709T will certainly help you make a decision on the purchase.
If you already are a holder of Kohler K-8709T, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Kohler K-8709T.
However, one of the most important roles played by the user manual is to help in solving problems with Kohler K-8709T. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Kohler K-8709T along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
