Instruction/ maintenance manual of the product I960SRDA AOC
Go to page of 80
60S / 60P (LED Backlight).
2 Safety ........................................................................................................................................................................ 4 National Conventions ..................................................
3 FCC Notice ...................................................................................................................................................... 69 W EEE De claration .................................................................
4 Safe ty National Con ventions The following subsections describe notational conventions used in this document. Notes, Cautions, and Warn ings Throughout this guide, blocks of text may be accompanied by an icon and printed in bold ty pe or in italic type.
5 Power The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local pow er company . The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin.
6 Installation Do not place the mo nitor on an unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a person and cause serious damage to thi s product. Use only a cart, stand, tripod, bracket, or ta ble recommended by the manufacture r or sold with this product.
7 Cleaning Clean the cabinet regularly with cloth. Y ou can use soft -detergent to wipe out the stain, instead of strong-detergent which will cauterize the product cabinet. W hen cleaning, make sure no detergent is leaked into the product. The cleaning cloth should not be too rough as it will scratch the screen surface.
8 Other If the product is emitting a strange smell, sound or smoke, disconnect the pow er plug IMMEDIA TEL Y and contact a Service Center . Make sure that the ventilating openings are not blocked by a table or curtain. Do not engage the LCD monitor in severe vibration or high impact conditions during operation.
9 S et up Contents of the Box Not all signal cables (Analog , Au dio, DVI,USB 、 DP and H DMI cables) will be provided for all countries and regions. Please check with the local dealer or AOC branch office for confirmation.
10 Setup Stand & Base Please setup or remove the base following the steps as below . 1>.Setup: Remove:.
11 2>.Setup: Remove:.
12 Adjusting Vie w ing Angle For optimal viewing it is recommended to look at the f ull face of the monitor , then adjust the monitor's angle to your own preference. Hold the stand so you will not topple the monitor w hen you change the monitor's angle.
13 2> Y ou are a ble to adjust the monitor's angle from -5° to 22 ° . NOTE: Do not touch the LCD screen when you change the angle. It may cause damage or break t he LCD screen.
14 Connecting the Monitor Cable Connections In Back of Monitor and Computer: E2060SL ： ⑤ ② 1. USB (Optional) 2. Power 3 HDMI (Optional) 4 .DVI (Optional) 5 . An alog (DB-15 VGA cable) 6. Line in (Opti onal) 7. USB fast charging p or t (Optional) 8.
15 3. (Optional – Requires a video card with DVI port)Connect one end of the DVI cable to the back of the monitor and connect the other end to the computer ‟ s DVI port. 4.(Optional – Requires a video card with HDMI port) - Connect one end of the HDMI cable to the back of the monitor and connect the other end to the computer’s HDMI port.
16 W all Mounti ng Preparing to Install An Optional Wall M ounting Ar m. This monitor can be attached to a wall mounting arm you purchase separately . Disconnect power before this procedure. Follow these steps: 1 Remove the base. 2 Follow the manufacturer's instructions to assemble the w all mounting arm.
17 Adjusting Setting Optimal Resol ution Windows V ista For Windows Vista: 1 Click ST ART . 2 Click CONTROL P ANE L. 3 Click Appearance and Personalization.
18 5 Click Display Settings. 6 Set the resolution SLIDE-BAR to Optimal preset resolution.
19 Windows XP For Windows XP: 1 Click ST ART . 2 Click SETTINGS. 3 Click CONTROL P ANEL. 4 Click Appearance and Themes. 5 Double click DISPLA Y ..
20 6 Click SETTINGS. 7 Set the resolution SLIDE-BAR to Optimal preset resolution Windows ME/2000 For Windows ME/2000: 1 Click ST ART . 2 Click SETTINGS. 3 Click CONTROL P ANEL. 4 Double click DISPLA Y . 5 Click SETTINGS. 6 Set the resolution SLIDE-BAR to Optimal preset resolution .
21 2. Set the “ view by ” to “ Category ” . 3. Click Appearance and Personalizatio n..
22 4. Click DISPLAY. 5. Set the resolution SLIDE-BAR to Optimal preset resolution ..
23 Hotkeys E2260P HU /E22 60S HU /E2460P WHU /E2460S WHU /E2460S HU /E2460P HU ： 1 Source/Auto/Exit 2 ECO(DCR /I -Care )/ < 3 Volume / > 4 Menu/Enter 5 Power I960SRDA/ I960PRDA/ E2060S W DU / .
24 E2060S WN /E2060S W ： 1 Auto/Exit 2 ECO(DCR)/< 3 4:3 or Wide / > 4 Menu/Enter 5 Power E960S RD ： 1 Source/Auto/Exit 2 ECO(DCR)/< 3 > 4 Menu/Enter 5 Power E2060SL ： 1 Auto/Exit 2 Clear Vision /< 3 4:3 or Wide / > 4 Menu/Enter 5 Power Power Press the Power button to turn o n/ off the monitor .
25 3. Press and hold “ - ” button for 5 seconds to activate the Clear Vision Demo, and a message of “ Clear Vi sion Demo: on” will be disp lay on the screen for a duration of 5 seconds. Press Menu or Exit button, the message will disappear . Press and hold “ - ” button for 5 second s again, Clear Vision Demo will be off.
26 OSD Setting Basic and simple instruction on the control key s. 1) Press the M ENU-button to activate the OSD window . 2) Press < or > to navigate through the functions. Once the desired function is highlighted, press the M ENU-button to activate it .
27 Luminance 1 Press (Menu) to display menu. 2 Press < or > to select (Luminance), and press to enter . 3 Press < or > to select submenu, and press to enter .
28 Brightness 0-100 Backlight Adjustment Contrast 0-100 Contrast from Digital-register. Eco mode Standard Standard Mode Text Text Mode Internet Internet Mode Game Game Mode Movie Movie Mode Sports Spo.
29 Image Setup 1 Press to display menu. 2 Press < or > to select ( Image Setup), and press to enter . 3 Press < or > to select submenu, and p ress to en ter . 4 Press < or > to adjust. 5 Press t o exit . Clock 0-100 Adjust picture Clock to reduce Vertical-Line noise.
30 Color Setup 1 Press (Menu) to display menu. 2 Press < or > to select (Color Setup ), and press to enter . 3 Press < or > to select submenu, and p ress to en ter . 4 Press < or > to adjust. 5 Press to ex it . Color setup. W arm Recall Warm Color Temperature from EEPROM .
31 Picture Boost 1 Press (Menu) to display menu. 2 Press < or > to select (Picture Boost), and press to enter . 3 Press < or > to s elect submenu, and press to enter . 4 Press < or > to adjust. 5 Press to ex it . Frame Size 14 -100 Adjust Frame Size Brightness 0-100 Adjust Frame Brightness Contrast 0-100 Adjust Frame Contrast H.
32 OSD Setup 1 Press (Menu) to display menu. 2Press < or > to select ( OSD Setup), and press to enter . 3 Press < or > to select submenu, and p ress to en ter . 4 Press < or > to adjust. 5 Press to exit . H.Position 0-100 Adjust the horizontal position of OSD V.
33 Extra 1 Press (Menu) to display menu. 2 Press < or > to select (Extra), and press to enter . 3 Press < or > to select submenu, and press to enter . 4 Press < or > to adjust. 5 Press to ex it . Input Select Auto / Analog / DVI / HDMI Select input s ig nal source.
34 Exit 1 Press (Menu) to display menu. 2 Press < or > to select (Exit), and press to enter . 3 Press to exit Exit Exit the main OSD.
35 LED Indicator Status LED Color Full Power Mode Green or Blue Active-off Mode Orange or red.
36 Driver Monitor Dri ver Windows 2000 1. Start Windows® 2000 2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'. 3. Double click on the 'Display' Icon. 4. Select the 'Settings' tab then click on 'Advanced.
37 Windows XP 1. Start Windows® X P 2. Click on the 'Start' button and then click on 'Control Panel'. 3. Select and click on the category ‘Appearance and T hemes’ 4.
38 5. Select the 'Settings' tab then click on the 'Advanced' button. 6. Select 'Monitor' tab - If the 'Properties' button is inactive, it means your monitor is properly configured. Please stop installation. - If the 'Properties' button is active, click on 'Properties' button.
39 8. Select the 'Install from a list or specific location [advanced]' radio button and then click on the 'Next' button. 9. Select the 'Don't Search. I will choose the driver to install' radio butt on. Then click on the 'Nex t' button.
40 Windows V ista 1. Click "Start " and "Control Panel". T hen, double -click on "Appearance an d Personalization". 2. Click "Personalization" and then "Display Settings". 3. Click "Advanced Settings.
41 4. Click "Properties" in the "M onitor" t ab. If the "Properties" button is deactivated, it me ans th e configur ation for your monitor is completed. T he monitor can be used as is. If the message "Windows needs..
42 Windows 7 1. Start Windows® 7 2. Click on the 'Start' button and then click on 'Control Panel'. 3. Click on the 'Display' icon.
43 4.Ckick on the “ Change display settings ” button. 5. Click the “ Advanced Settings” button. 6. Click the “Monitor” tab and then click the “Properties” button.
44 7. Click the “Driver” tab. 8. Open the "Update Driver Software-Generic PnP Monitor" window by clicking on “Update Driver ... “ and then click the "Browse my computer for driver software" button. 9. Select "Let me pick from a list of device drivers on my computer" .
45 10. Click the “Have Disk” button. Click on the “Browse” button and navigate to the following directory: X: Drivermo dule name (w here X is the drive letter designator for the CD-ROM drive). 11. Select the "xxx.inf" file and click the “Open” button.
46 Windows 8 1. Start Windows® 8 2. Right click and click All apps at the bottom-right of the screen. 3. Click on the “ Control panel ” icon 4. Set the “ V iew by ” to “Large icons” or “Small icons” .
47 5. Click on the “ Display ” icon. 6. Click on the “Change display settings” button. 7. Click the “ Advanced Settings” button ..
48 8. Click the “Monitor” tab and then click the “Properties” button . 9. Click the “Driver” tab. 10. Open the “ Update Driver Software-Generic PnP Monitor ” w indow by clicking on “ Update Driv er ... “ and then click the "Browse m y co mputer for driver software" butt on.
49 11. Select "Let me pick from a list of device drivers on my computer" . 12. Click the “Have Disk” button. Click on the “Browse” button and navigate to the following directory: X: Drivermo dule name (where X is the drive letter designator for the CD-ROM drive).
50 i-Menu Welcome to “i - Menu” softw are by AOC. i -Menu makes it easy to adjust your monitor display setting by usi ng on screen menus instead of the OSD button on the monitor .
51 e-Saver W elc ome to use AOC e-Saver monitor power management software! The AOC e- Saver features Smart Shutdow n functions for your monitors, allow s your monitor to timely shu tdown w hen PC unit is at any status (On, Off, Sleep or Screen Saver); the actual shutdown time depends on your preferences (see example below).
52 Screen+ Welcome to "Screen+" softw are by AOC, Screen+ softw are is a desktop screen splitting tool, it splits the desktop into different panes, each pan e displays a different w indow . Y ou on ly need to drag the window to a corresponding pan e, when you want to access it.
53 T roubleshoot Problem & Question Possible Solutions Power LED Is Not ON Make sure the power button is ON and the Pow er Cord is properly connected to a grounded power outlet and to the monitor . No images on the screen Is the power cord connected properly? Check the power cord connection and power supply .
54 Monitor Is Stuck In A ctive Off-Mode" The Computer Power Switch should be in the ON position. The Computer Video Card should be snugly f itted in its slot. Make sure the monitor's video cable is properly connected to the computer . Inspect the monitor's video cable and make sure no pin is bent.
55 Specification General Specifi cation Panel Model name I960SRDA/I960PRDA/E960S RDA / E960P RDA / E960S RD Driving system TFT Color LCD Viewable Image Size 48. 2cm diagonal/ 48. 0cm diagonal （ I960SRDA/I960PRDA ） Pixel pitch 0.294mm(H)X0.294mm(V)/ 0.
56 Panel Model name E2060S WN /E2060S WDN /E20 60S WDAN /E2060S WDA / E2060P WDA /E2060S W /E2060S W D /E2060S W DU /E2060 SL Driving system TFT Color LCD Viewable Image Size 49.5cm diagonal Pixel pitch 0.27mm(H)X0.27mm(V) Pixel pitch (E2060SL) 0.3177mm(H) x 0.
57 Off timer 0-24 hrs Speakers(E2060S WDU /E2060S WDA / E2060P WDA /E2060S W DA N ) 2W X2 Physical Characteristics Connector T ype (E2060S WDU /E2060S WDN/ E2060S WDAN /E2060S WDA / E2060P WDA /E2060S.
58 Panel Model name E2260P HU /E2260S HU /E2260P DA /E2260 S DA /E2260S D /E2260P Q Driving system TFT Color LCD Viewable Image Size 55.86 cm diagonal Pixel pitch 0.
59 Operating 10% to 85% (non-condensing) Non-Operating 5% to 93% (non-condensing) Panel Model name E2460P W HU / E2460S W HU Driving system TFT Color LCD Viewable Image Size 59.8 cm diagonal Pixel pitch 0. 2715 mm(H) x 0. 2715 mm(V) Video R, G, B Analog lnterface & Digital Interface & HDMI lnterface Separate Sync H/V TTL Display Color 16.
60 Preset Displa y Modes 19 R ST ANDARD RESOLUTION HORIZONT A L FREQUENCY(kHZ) VERTIC AL FREQUENCY(Hz ) VGA 640× 480@ 60Hz 31.469 59.940 VGA 640× 480@ 67Hz 35.000 66.667 VGA 640× 480@ 72Hz 37.861 72.809 VGA 640× 480@ 75Hz 37.500 75.000 Dos-mode 720× 400@ 70Hz 31.
61 19.5w ST AND RESOLUTION HORIZONT A L FREQUENCY(kHZ) VERTIC AL FREQUENCY(Hz ) VGA 640× 480 @60Hz 31.469 59.940 VGA 640× 480 @67Hz 35.000 66.667 VGA 640× 480 @72Hz 37.861 72.809 VGA 640× 480 @75Hz 37.500 75.000 Dos-mode 720× 400 @70Hz 31.469 70.
62 19.5w(E2060SL) Standard Resolution H. Frequency (kHz) V. Frequency (Hz ) VGA 640× 480 @60Hz 31.469 59.940 VGA 640× 480 @67Hz 35.000 66.667 VGA 640× 480 @72Hz 37.861 72.809 VGA 640× 480 @75Hz 37.500 75.000 Dos-mode 720× 400 @70Hz 31.469 70.087 SVGA 800× 600 @56Hz 35.
63 22w ST ANDARD RESOLUTION HORIZONT A L FREQUENCY(kHZ) VERTIC AL FREQUENCY(Hz ) VGA 640× 480@ 60Hz 31.469 59.940 VGA 640× 480@ 72Hz 37.861 72.809 VGA 640× 480@ 75Hz 37.500 75.000 SVGA 800× 600@ 56Hz 35.156 56.250 SVGA 800× 600@ 60Hz 37.879 60.317 SVGA 800× 600@ 72Hz 48.
64 23.6w ST ANDARD RESOLUTION HORIZONT AL FREQUENCY(kHZ) VERTICAL FREQUENCY(Hz) VGA 640× 480 @60Hz 31.469 59.940 VGA 640× 480 @67Hz 35.000 66.667 VGA 640× 480 @72Hz 37.861 72.809 VGA 640× 480 @75Hz 37.500 75.000 Dos-mode 720× 400 @70Hz 31.469 70.
65 24w ST AND RESOLUTIO N Horizontal V ertical VGA 640× 480@ 60Hz 31.469 59.94 640× 480@ 72Hz 37.861 72.809 640× 480@ 75Hz 37.5 75 SVGA 800× 600@ 56Hz 35.156 56.25 800× 600@ 60Hz 37.879 60.317 800× 600@ 72Hz 48.077 72.188 800× 600@ 75Hz 46.875 75 XGA 1024× 768 @60Hz 48.
66 Pin A s signmen ts Pin Number 15 -Pin Side of the Signal Cable 1 Video-Red 2 Video-Green 3 Video-Blue s N.C. 5 Detect Cable 6 GND-R 7 GND-G 8 GND-B 9 +5V 10 Ground 11 N.
67 Pin No. Signal Name Pin No. Signal Name Pin No. Signal Name 1 TMDS Data 2+ 9 TMDS Data 0 17 DDC/CEC Ground 2 TMDS Data 2 Shield 10 TMDS Clock + 18 +5V Power 3 TMDS Data 2 11 TMDS Clock Shield 19 Hot Plug Detect 4 TMDS Data 1+ 12 TMDS Clock 5 TMDS Data 1Shield 13 CEC 6 TMDS Data 1 14 Reserved (N.
68 Plug and Pla y Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B cap abilities according to the VESA DDC ST ANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, c ommunicate additional information about its display capabilities.
69 Regulation FCC Notice FCC Class B Radio Frequency Interference State ment W ARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested an d found to co mply w ith the limits for a Cl ass B digital devi ce, pursuant to Part 15 of the FCC Rules.
70 WEEE Declaration Disposal of Was te Equipment by Users in Private Household in the European Union. This symbol on the product or on its packaging indicates that this product must not be disp osed of with your other household waste.
71 EP A Energy Star ENERGY ST AR® is a U.S. registered mark. As an ENERGY ST AR ® Partner , AOC International (Europ e) BV and Envision Peripherals, Inc.
72 EPE A T Declarat ion EPEA T is a system to help purchasers in the public and private sectors evaluate, compare and select desktop computers, notebooks and monitors based on their environmental attributes.
73 Service W arranty Statement fo r Europe LIMITED THREE-YEAR W ARRANTY* For AOC LCD M onitors sold within Europe, AOC International (Eur ope) B.V . warrants this product to be free from defects in material and workmanship for a period of Three (3) years after the original date of consumer purchase.
74 This limited warranty does not cover any of the product firmware or hardware that you or an y third party have modified or altered; you bear the sole responsibility and liability for any such modifications or alteration. All AOC LCD M onitors are produced according to the ISO 9241-307 Class 1 pixel policy standards.
75 Service W arranty Statement fo r Middle East and Africa (MEA ) And The Commonwealt h of Independent St ates (CIS) LIMITED ONE to THREE YEA RS W ARRANTY* For AOC LCD M onitors sold within the Middle East and Africa (MEA) and the Commonwealth of Independent States (CIS), AOC Internat ional (Europe) B.
76 Damages during transport due to improper packaging Improper installation or maintenance other then in accordance w ith AOC’ s user manual Misuse Neglect Any cause other than o.
77 W arranty Statement for North & South A merica (excluding Brazil) WARR ANTY ST A TEMENT for AOC Color M onitors Including those Sold within North America as Specified Envision Peripherals, Inc.
78 MERCHANT A BILITY AND FI TNESS FOR A P ART ICULAR PURPOSE) ARE LIMIT ED IN DURA TION T O A PERIOD OF T HREE (3) YEARS FOR P ART S AND LABOR AND ONE (1) YEAR FO R CRT TUBE OR LCD P ANEL FROM T HE ORIGINAL DA TE OF CONSUMER PURCHASE. NO WARRANT IES (EITHER EXPRESSED OR IMPLIED) APPL Y AFTER THIS PERIOD.
79 TCO DOCUMENT (FOR TCO CERTIFIED MODELS).
80.
An important point after buying a device AOC I960SRDA (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought AOC I960SRDA yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data AOC I960SRDA - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, AOC I960SRDA you will learn all the available features of the product, as well as information on its operation. The information that you get AOC I960SRDA will certainly help you make a decision on the purchase.
If you already are a holder of AOC I960SRDA, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime AOC I960SRDA.
However, one of the most important roles played by the user manual is to help in solving problems with AOC I960SRDA. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device AOC I960SRDA along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
