Instruction/ maintenance manual of the product RFS 3570 Kodak
Go to page of 220
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . User’s Manual KODAK Professional RFS 3570 Film Scanner © Eastman Kodak Company, 1997.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii Important Safeguards and Precautions WARNING: To prevent fire or shock hazard, do not expose unit to rain or moisture. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv Cleaning — Unplug the unit before cleaning. Clean only the outside cabinet with a damp cloth. Do not use liquid cleaners or aerosol cleaners. Attachments — Do not use attachments that are not recommended.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . v Power-Cord Protection — Route power-supply cords so that they are not likely to be walked on or pinched by items placed on or against them; pay particular attention to cords at plugs, receptacles, and the point where they leave the unit.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi – If the equipment has been exposed to rain or water. – If the unit does not operate normally according to the operating instructions. – If the unit has been dropped or the housing has been damaged.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la classe A prescrites dans le règlement sur le broullage radioélectrique édicté par le Ministère des Communications du Canada.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . viii T echnical Assistance Refer to the following sources for assistance if you have questions as you work with the Scanner. If you encounter difficulties with hardware, with scanned images or with product performance, refer to “Appendix C — Troubleshooting.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix Contents 1 Introduction 1-1 2 Before You Begin — Macintosh Computer 2-1 Required Hardware 2-2 Computer 2-2 Monitor 2-2 Display Card 2-2 R.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . x 4 Loading the Film and Slide Holders — Macintosh Computer 4-1 Loading 35 mm Film and Slides 4-2 Loading 35 mm Film into the 35 mm Film Hol.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi Change Contrast 5-20 Choose the Resolution 5-20 “Crop” the Image 5-21 Scan the Image into Photoshop 5-21 Scan Additional Images 5-23 Tu.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii 8 Loading the Film and Slide Holders — PC 8-1 Loading 35 mm Film and Slides 8-2 Loading 35 mm Film into the 35 mm Film Holder 8-2 Loadin.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii Change Contrast 9-20 Choose the Resolution 9-20 “Crop” the Image 9-21 Scan the Image 9-22 Scan Additional Images 9-23 Turning Off the.
.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Introduction 1-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Introduction The features of the Scanner include: Fast scanning speed. Quick and easy loading of film—no position adjustments are required. User-selectable autofocus. High quality analog-to-digital conversion with 12 bits per RGB color.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Introduction 1-3 The KODAK Drivers are used to capture images from the scanned film (negative or positive), and open that image data in a window in your supported image editing software. You can then edit images and save them as files on your computer hard disk.
.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Before You Begin — Macintosh Computer 2-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Before You Begin — Macintosh Computer Required Hardware Computer Apple Macintosh Computer that: supports 32-Bit QuickDraw software; has .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Before You Begin — Macintosh Computer 2-3 Required Software Apple System software 7.0, 7.1, 7.1.2, or 7.5 to 7.5.3 and 32-bit QuickDraw. Consult your Apple manuals for installation instructions if this software is not already installed.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Before You Begin — Macintosh Computer Optional Printers Suggested printers for use with the scanner appear in “Appendix I — Optional Equipment & Spare Parts List.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation (Hardware & Software) — Macintosh Computer 3-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Installation (Hardware & Software) — Macintosh Computer Installing the Scanner Hardware Follow these instructions to connect the Scanner to a power source, to connect the Scanner to your computer, and to set the Scanner SCSI Identification number.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation (Hardware & Software) — Macintosh Computer 3-3 Connecting the Scanner to Y our Computer Follow the instructions in this section to connect the Scanner, a non- terminated SCSI device, to your Macintosh computer by using the sup- plied cable and terminator.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 Installation (Hardware & Software) — Macintosh Computer 2. Find the SCSI port, also called a SCSI connector, on the back of the computer (not the back of the Scanner), and determine whether or not a device (for example a disk drive) is attached.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation (Hardware & Software) — Macintosh Computer 3-5 If No External SCSI Devices Are Connected Complete these steps if no SCSI devices are connected to your Macintosh computer; otherwise proceed to “If External SCSI Devices Are Connected” later in this chapter.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6 Installation (Hardware & Software) — Macintosh Computer 2. Attach the 25-pin SCSI connector of the cable to the SCSI port on the back of the Macintosh computer.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation (Hardware & Software) — Macintosh Computer 3-7 3. Attach the other end of the cable to either of the identical SCSI ports on the back of the Scanner. Seat the connector firmly and pinch the thin wire clamps shut.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8 Installation (Hardware & Software) — Macintosh Computer 4. Attach the SCSI terminator (supplied with the Scanner) to the empty SCSI port on the Scanner, seat the terminator firmly, and pinch the thin wire clamps shut.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation (Hardware & Software) — Macintosh Computer 3-9 If External SCSI Devices Are Connected Complete these steps if one or more e.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10 Installation (Hardware & Software) — Macintosh Computer 2. Locate the two identical SCSI ports and thin wire clamps on the back of the Scanner. Serial Number 2 SCSI ID 3 3570 - BACK OF FILM SCANNER Thin Wire Clamps Two Identical SCSI Ports 3.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation (Hardware & Software) — Macintosh Computer 3-11 4. Select the appropriate instructions from the two sets that follow, according to whether or not an external device is terminated inter- nally.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12 Installation (Hardware & Software) — Macintosh Computer Follow these steps if none of the connected devices is terminated internall.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation (Hardware & Software) — Macintosh Computer 3-13 2. Attach the other end of the cable to either of the identical SCSI ports on the back of the Scanner. Seat the connector firmly and pinch the wire clamps shut.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14 Installation (Hardware & Software) — Macintosh Computer 3. Attach the SCSI terminator (supplied with the Scanner) to the empty SCSI port on the Scanner, seat the terminator firmly, and pinch the wire clamps shut.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation (Hardware & Software) — Macintosh Computer 3-15 Follow these steps if one of the connected devices is terminated internally: NOTE: In the following steps, you will place the Scanner in the chain just before the terminated device.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16 Installation (Hardware & Software) — Macintosh Computer 2. Disconnect the end of that cable from the internally terminated device. Do not disconnect the other end of the cable. Back of Macintosh Computer Step 2 Internally Terminated Device 3.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation (Hardware & Software) — Macintosh Computer 3-17 4. Attach the end of the cable you just disconnected to either of the identical SCSI ports on the back of the Scanner. Seat the connector firmly, and pinch the thin wire clamps shut.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18 Installation (Hardware & Software) — Macintosh Computer 5. Attach the Scanner to the internally terminated device by plugging one end of your 50-pin to 50-pin SCSI cable into the empty SCSI port on the Scanner and the other end into the empty SCSI port on the terminated device.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation (Hardware & Software) — Macintosh Computer 3-19 Setting the Scanner SCSI Identification Number Follow the steps below to set the SCSI identification (ID) number for the Scanner.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20 Installation (Hardware & Software) — Macintosh Computer Each SCSI device connected to the same computer must have a different SCSI ID number. Your Macintosh Computer is number 7, and your internal hard disk is probably 0.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation (Hardware & Software) — Macintosh Computer 3-21 Installing the KODAK Driver for Adobe Photoshop Software (Macintosh) Follow these steps to install the driver. This is a onetime operation that you must perform before you can obtain images from the Scanner.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22 Installation (Hardware & Software) — Macintosh Computer 8. Complete part A of this step for supported Photoshop versions before version 2.5, and part B for versions 2.5 and later. A.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Loading the Film and Slide Holders — Macintosh Computer 4-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 Loading the Film and Slide Holders — Macintosh Computer Loading 35 mm Film and Slides Loading 35 mm Film into the 35 mm Film Holder Up to six frames from a strip of 35 mm film of any length can be posi- tioned for scanning at one time.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Loading the Film and Slide Holders — Macintosh Computer 4-3 4. Tuck the lower edge of the film under the tabs that run along the hinge. 5. Center the film so that each frame aligns with a frame in the film holder.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 Loading the Film and Slide Holders — Macintosh Computer Loading 35 mm Film and Slide Holders into the Scanner To load a 35 mm film or slide holder into the Scanner: 1. If the single-frame holder adapter is in the Scanner, remove it.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Loading the Film and Slide Holders — Macintosh Computer 4-5 2. If the 35 mm multi-frame holder adapter is not in the Scanner, put it in place in the Scanner in the orientation shown.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6 Loading the Film and Slide Holders — Macintosh Computer 3. Orient the film or slide holder as follows: Film Holder: Make sure that the two orientation labels face you, that the film images read in the direction of the letter “R,” and that the “R” is right-side up.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Loading the Film and Slide Holders — Macintosh Computer 4-7 4. Slide the holder into the left or right opening of the 35 mm multi- frame holder adapter.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8 Loading the Film and Slide Holders — Macintosh Computer Loading Film Sizes Other Than 35 mm Loading Film into the Film Holder Follow the steps below to load film sizes other than 35 mm into their film holders.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Loading the Film and Slide Holders — Macintosh Computer 4-9 3. Place your film in the bottom of the film holder so that: Images are facing you as you would see them in real life (not mirror-imaged).
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10 Loading the Film and Slide Holders — Macintosh Computer Loading Film Holders (Other Than 35 mm Sizes) into the Scanner 1. If the 35 mm multi-frame holder adapter is in the Scanner, remove it.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Loading the Film and Slide Holders — Macintosh Computer 4-11 2. If the single-frame holder adapter is not in the Scanner, put it in place in the Scanner. K OD AK Pr ofessional RFS 3570 F ilm Scanner Single-frame Holder Adapter .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12 Loading the Film and Slide Holders — Macintosh Computer 3. Place the film holder into the Scanner by sliding it down completely into place behind the single-frame holder adapter; be certain that the film holder is aligned with the indentation in the frame in the Scanner.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the KODAK Driver for Adobe Photoshop (Macintosh) 5-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Using the KODAK Driver for Adobe Photoshop (Macintosh) We assume you are familiar with the operation of your Macintosh Com- puter and Adob.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the KODAK Driver for Adobe Photoshop (Macintosh) 5-3 Displaying the KODAK Driver W indow Follow the steps in this section each time that you want to acquire data from the Scanner from within Adobe Photoshop.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4 Using the KODAK Driver for Adobe Photoshop (Macintosh) 6. Wait, and when start-up is complete, the KODAK Driver window appears.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the KODAK Driver for Adobe Photoshop (Macintosh) 5-5 Producing Scanned Images In this section, you will load your film or slides into the Scanner and then generate scans by making selections from the KODAK Driver window.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6 Using the KODAK Driver for Adobe Photoshop (Macintosh) Operating the KODAK Driver Follow the steps in this section to use the controls on the KODAK Driver window.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the KODAK Driver for Adobe Photoshop (Macintosh) 5-7 Wait as a “Calibration Procedure” alert box appears; follow the directions it contains as outlined in detail in parts A through E of this step.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8 Using the KODAK Driver for Adobe Photoshop (Macintosh) B. If a single-frame film holder is in the Scanner, remove it.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the KODAK Driver for Adobe Photoshop (Macintosh) 5-9 C. If the single-frame holder adapter is not in the Scanner, put it in place in the Scanner.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10 Using the KODAK Driver for Adobe Photoshop (Macintosh) D. Put the calibration mask into the Scanner. As you insert it into the Scanner, the words “Calibration Mask” should face forward as shown below.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the KODAK Driver for Adobe Photoshop (Macintosh) 5-11 E. Click OK. The Scanner will then display several messages.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12 Using the KODAK Driver for Adobe Photoshop (Macintosh) Change the Magnification Adjustment 4. (Optional) Change the M AGNIFICATION A DJUSTMENT if desired by moving its slider or typing an integer value from -10 to 10 in the text box to the right of the slider.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the KODAK Driver for Adobe Photoshop (Macintosh) 5-13 Black borders above and below the image indicate underscanning . . . Missing image above and below the scan area indicate overscanning .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14 Using the KODAK Driver for Adobe Photoshop (Macintosh) You determine the “optimal” setting for your images. To ensure that as many pixels of the imager as possible are used for you images, your image should fill the scanning area vertically.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the KODAK Driver for Adobe Photoshop (Macintosh) 5-15 Select the Image 6. A. (Optional) Click S ELECT .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16 Using the KODAK Driver for Adobe Photoshop (Macintosh) Set Auto Balance 7. (Optional) Set A UTO B AL . For most customers the A UTO B AL suggested setting of “on” will automatically provide the proper “scene” balance.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the KODAK Driver for Adobe Photoshop (Macintosh) 5-17 Set the Image to Black and White 10. (Optional) Click B & W to have all subsequent actions — including the final scan — occur in black and white.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18 Using the KODAK Driver for Adobe Photoshop (Macintosh) To deselect an area, click once inside or outside the selection rectangle. B. Click F OCUS . You will hear one buzz after another during the focusing process.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the KODAK Driver for Adobe Photoshop (Macintosh) 5-19 Click the C LICK W HITE button, then click a neutral spot in the image known to be gray or white. (Do not click a dark shadow or a bright highlight or overexposed area.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-20 Using the KODAK Driver for Adobe Photoshop (Macintosh) Change Contrast 14. (Optional) Use the scroll bars or type new values (-10 to 10) to adjust the contrast among image elements (pixels).
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the KODAK Driver for Adobe Photoshop (Macintosh) 5-21 “Crop” the Image 16. Follow part A or part B of this step depending on whether or not you want to crop the image. A. If you do not want to crop the image, click once on the image to remove the selection (cropping) rectangle.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-22 Using the KODAK Driver for Adobe Photoshop (Macintosh) time while working with the scanner, clean the scanner “diffuser” (a 3 x 4-inch piece of white plastic), as summarized in this note, and as fully described at the end of “Appendix C — Troubleshooting.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the KODAK Driver for Adobe Photoshop (Macintosh) 5-23 18. (Optional) Edit the image as desired.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-24 Using the KODAK Driver for Adobe Photoshop (Macintosh) T urning Off the Scanner When your scans are complete, quit Adobe Photoshop and turn off your computer and the Scanner as follows: CAUTION: The Scanner must be turned off (and on) only when your Macintosh computer is off.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the KODAK Driver for Adobe Photoshop (Macintosh) 5-25 Reference: Buttons and Indicators 90 ° CCW Rotates the image 90 ° counterclockwise. 90 ° CW Rotates the image 90 ° clockwise. 180 ° Rotates the image 180 ° .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-26 Using the KODAK Driver for Adobe Photoshop (Macintosh) B RIGHTNESS Adjusts the level of brightness of the entire image. NOTE: Refer to “Change Brightness” earlier in this chapter for additional information on this option.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the KODAK Driver for Adobe Photoshop (Macintosh) 5-27 scan — leaving a selection rectangle in the image. Then click S CAN to scan the cropped area into Adobe Photoshop, resulting in a smaller image size.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-28 Using the KODAK Driver for Adobe Photoshop (Macintosh) G AMMA A measure of contrast in photographic images. See C ONTRAST . I MAGE S IZE Displays the quantity of data that will be returned from the scan.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the KODAK Driver for Adobe Photoshop (Macintosh) 5-29 menu and type a value from 1 to 100 in the text box that appears to the right of the RES menu. NOTES: Different resolutions produce different image sizes, as shown in the I MAGE S IZE information below the image.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-30 Using the KODAK Driver for Adobe Photoshop (Macintosh) V IEW C HANGES Using the last scanned or prescanned image, this button produces an.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Before You Begin — PC 6-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2 Before You Begin — PC Required Hardware Computer An 80386 or higher computer that has: a minimum of 8 megabytes (MB) random access memory (RAM) (32 MB RAM or more is recommended for fastest scan times) that can operate Windows 3.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Before You Begin — PC 6-3 Required Software Microsoft Windows, version 3.1, Windows 95. A TWAIN compliant software application. The Kodak driver for use with TWAIN-compliant PC applications can be used with Adobe Photoshop 3.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 Before You Begin — PC Optional Printers Suggested printers for use with the scanner appear in “Appendix I — Optional Equipment & Spare parts List.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation (Hardware & Software) — PC 7-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Installation (Hardware & Software) — PC Installing the Scanner Hardware Follow these instructions to connect the Scanner to a power source, to connect the Scanner to your computer, and to set the Scanner SCSI identification number.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation (Hardware & Software) — PC 7-3 Installing a SCSI Host Adapter CAUTION: Only trained and qualified technical personnel should perform the following procedures.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4 Installation (Hardware & Software) — PC 3. Install the SCSI Host Adapter for your PC according to the manufacturer’s installation instructions. When installation is complete, a SCSI2 connector should be available on the back of your PC, as shown in one example below.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation (Hardware & Software) — PC 7-5 If No External SCSI Devices Are Connected Complete these steps if no SCSI devices are connected to your computer; otherwise proceed to “If External SCSI Devices Are Connected” later in this chapter.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6 Installation (Hardware & Software) — PC 2. Attach the 50-pin SCSI2 HD connector of the cable to the SCSI port on the back of the computer.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation (Hardware & Software) — PC 7-7 3. Attach the other end of the cable to either of the identical SCSI ports on the back of the Scanner. Seat the connector firmly and pinch the thin wire clamps shut.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8 Installation (Hardware & Software) — PC 4. Attach a SCSI terminator (supplied with the Scanner) to the empty SCSI port on the Scanner, seat the terminator firmly, and then pinch the thin wire clamps shut.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation (Hardware & Software) — PC 7-9 If External SCSI Devices Are Connected Complete these steps if one or more external SCSI devices are connected to your computer; otherwise continue at “Setting the Scanner SCSI Identi- fication Number” later in this chapter.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10 Installation (Hardware & Software) — PC 1. Select your SCSI cable with identical 50-pin SCSI connectors at each end. NOTE: This cable is not packed with the Scanner but is available through Kodak.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation (Hardware & Software) — PC 7-11 2. Locate the two identical SCSI ports and thin wire clamps on the back of the Scanner. Serial Number 2 SCSI ID 3 3570 - BACK OF FILM SCANNER Thin Wire Clamps Two Identical SCSI Ports 3.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-12 Installation (Hardware & Software) — PC 4. Select the appropriate instructions from the two sets that follow, according to whether or not an external device is terminated inter- nally.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation (Hardware & Software) — PC 7-13 Follow these steps if none of the connected devices is terminated internally (and any exter.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-14 Installation (Hardware & Software) — PC 2. Attach the other end of the 50-pin to 50-pin SCSI cable to either of the identical SCSI ports on the back of the Scanner. Seat the connector firmly and pinch the wire clamps shut.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation (Hardware & Software) — PC 7-15 Follow these steps if one of the connected devices is terminated internally: NOTE: In the following steps, you will place the Scanner in the chain just before the terminated device.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-16 Installation (Hardware & Software) — PC 2. Disconnect the end of that cable from the internally terminated device. Do not disconnect the other end of the cable. Step 2 Internally Terminated Device Back of PC 3.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation (Hardware & Software) — PC 7-17 4. Attach the end of the cable you just disconnected to either of the identical SCSI ports on the back of the Scanner. Seat the connector firmly and pinch the thin wire clamps shut.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-18 Installation (Hardware & Software) — PC 5. Attach the Scanner to the internally terminated device by plugging one end of your 50-pin to 50-pin SCSI cable into the empty SCSI port on the Scanner and the other end into the empty SCSI port on the terminated device.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation (Hardware & Software) — PC 7-19 Setting the Scanner SCSI Identification Number Follow the steps below to set the SCSI identification (ID) number for the Scanner.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-20 Installation (Hardware & Software) — PC Each SCSI device connected to the same computer must have a different SCSI ID number.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation (Hardware & Software) — PC 7-21 KODAK TW AIN Driver This section describes how to install the KODAK TWAIN Driver available for use with the Scanner.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-22 Installation (Hardware & Software) — PC Installing TW AIN Compliant KODAK Driver NOTES: We assume that a technician has installed a supported SCSI host adapter in your PC.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation (Hardware & Software) — PC 7-23 5. Insert the diskette into your floppy drive. 6. Open the README file for the installation process by following these steps: A. Choose R UN from the F ILE menu.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-24 Installation (Hardware & Software) — PC B. Click I NSTALL ; wait as a box indicates progress in completing the installation. C. When you see the TWAIN installation complete screen, click V IEW README.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Loading the Film and Slide Holders — PC 8-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 Loading the Film and Slide Holders — PC Loading 35 mm Film and Slides Loading 35 mm Film into the 35 mm Film Holder Up to six frames from a strip of 35 mm film of any length can be posi- tioned for scanning at one time.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Loading the Film and Slide Holders — PC 8-3 4. Tuck the lower edge of the film under the tabs that run along the hinge. 5. Center the film so that each frame aligns with a frame in the film holder.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4 Loading the Film and Slide Holders — PC Loading 35 mm Film and Slide Holders into the Scanner To load a 35 mm film or slide holder into the Scanner: 1. If the single-frame holder adapter is in the Scanner, remove it.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Loading the Film and Slide Holders — PC 8-5 2. If the 35 mm multi-frame holder adapter is not in the Scanner, put it in place in the Scanner in the orientation shown.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6 Loading the Film and Slide Holders — PC 3. Orient the film or slide holder as follows: Film Holder: Make sure that the two orientation labels face you, that the film images read in the direction of the letter “R,” and that the “R” is right-side up.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Loading the Film and Slide Holders — PC 8-7 4. Slide the holder into the left or right opening of the 35 mm multi- frame holder adapter.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8 Loading the Film and Slide Holders — PC Loading Film Sizes Other Than 35 mm Loading Film into the Film Holder Follow the steps below to load film sizes other than 35 mm into their film holders.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Loading the Film and Slide Holders — PC 8-9 3. Place your film in the bottom of the film holder so that: Images are facing you as you would see them in real life (not mirror-imaged). Any edge printing on the film is readable from left to right.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10 Loading the Film and Slide Holders — PC Loading Film Holders (Other Than 35 mm Sizes) into the Scanner 1. If the 35 mm multi-frame holder adapter is in the Scanner, remove it. KOD AK Pr ofessional RFS 3570 Film Scanner 35 mm Multi-frame Holder Adapter .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Loading the Film and Slide Holders — PC 8-11 2. If the single-frame holder adapter is not in the Scanner, put it in place in the Scanner. K OD AK Pr ofessional RFS 3570 F ilm Scanner Single-frame Holder Adapter .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12 Loading the Film and Slide Holders — PC 3. Place the film holder into the Scanner by sliding it down completely into place behind the single-frame holder adapter; be certain that the film holder is aligned with the indentation in the frame in the Scanner.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using KODAK Drivers with Windows Applications — PC 9-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2 Using KODAK Drivers with Windows Applications — PC The end of the chapter also includes a full reference section of all soft- ware features.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using KODAK Drivers with Windows Applications — PC 9-3 Using a KODAK Driver for TW AIN Compliant PC Applications Not all TWAIN compliant applications provide access to TWAIN drivers in the same way.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4 Using KODAK Drivers with Windows Applications — PC 4. If it has not been configured to start automatically, start Microsoft Windows by typing WIN at the DOS prompt (C:>) and pressing Enter.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using KODAK Drivers with Windows Applications — PC 9-5 5. Choose TWAIN (TWAIN A CQUIRE in Adobe Photoshop 3.0) on the A CQUIRE submenu on the F ILE menu. 6. Wait, and when start-up is complete, the KODAK Driver window appears.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6 Using KODAK Drivers with Windows Applications — PC Producing Scanned Images In this section you will load your film or slides into the Scanner and then generate scans by making selections from the KODAK Driver window.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using KODAK Drivers with Windows Applications — PC 9-7 Operating the KODAK Driver Follow the steps in this section to use the controls on the KODAK Driver window.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8 Using KODAK Drivers with Windows Applications — PC Wait as a “Calibration Procedure” alert box appears; follow the directions it contains as outlined in detail in parts A through E of this step.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using KODAK Drivers with Windows Applications — PC 9-9 B. If a single-frame film holder is in the Scanner, remove it.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10 Using KODAK Drivers with Windows Applications — PC C. If the single-frame holder adapter is not in the Scanner, put it in place in the Scanner.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using KODAK Drivers with Windows Applications — PC 9-11 D. Put the calibration mask into the Scanner. As you insert it into the Scanner, the words “Calibration Mask” should face forward as shown below.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-12 Using KODAK Drivers with Windows Applications — PC E. Click OK. The Scanner will then display several messages.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using KODAK Drivers with Windows Applications — PC 9-13 Change the Magnification Adjustment 4. (Optional) Change the M AGNIFICATION A DJUSTMENT if desired by moving its slider or typing an integer value from -10 to 10 in the text box to the right of the slider.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-14 Using KODAK Drivers with Windows Applications — PC Black borders above and below the image indicate underscanning . . . . . . which occurs at the negative end of the slider. Missing image above and below the scan area indicate overscanning .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using KODAK Drivers with Windows Applications — PC 9-15 You determine the “optimal” setting for your images. To ensure that as many pixels of the imager as possible are used for you images, your image should fill the scanning area vertically.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-16 Using KODAK Drivers with Windows Applications — PC A low-resolution black-and-white scan occurs every two seconds, with the image displayed in the window. (The S ELECT button changes to S TOP S ELECT .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using KODAK Drivers with Windows Applications — PC 9-17 Rotate the Image 8. (Optional) Click 90 ° CCW, 180 ° , or 90 ° CW to rotate the image 90 ° counterclockwise (CCW), 180 ° , or 90 ° clockwise (CW), respectively.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-18 Using KODAK Drivers with Windows Applications — PC A. Drag the handle(s) of the selection rectangle around the portion of the image that is sharpest (in the best focus); the area should contain a significant amount of detail.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using KODAK Drivers with Windows Applications — PC 9-19 C. Click once to remove the selection rectangle; this will ensure that later when you do a scan you obtain the full image, not just the small portion within the focus rectangle.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-20 Using KODAK Drivers with Windows Applications — PC will be saved from one work session to the next for the selected film type until they are changed.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using KODAK Drivers with Windows Applications — PC 9-21 Additionally, you can choose C USTOM from the RES drop down list box and type a value from 1 to 100 in the text box that appears to the right of the RES menu.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-22 Using KODAK Drivers with Windows Applications — PC step); if you do not select a specific portion, the entire image will be scanned. Note that I MAGE S IZE , shown below the image, changes to reflect the size of the area you selected.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using KODAK Drivers with Windows Applications — PC 9-23 B. Orient the dust removal tool as shown below, and with an up and down motion, clean the surface of the diffuser making sure the fiber strip makes contact with the diffuser.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-24 Using KODAK Drivers with Windows Applications — PC T urning Off the Scanner When your scans are complete, exit from your application and turn off your computer and the Scanner as follows: CAUTION: The Scanner must be turned off (and on) only when your computer is off.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using KODAK Drivers with Windows Applications — PC 9-25 Reference: Buttons and Indicators 90 ° CCW Rotates the image 90 ° counterclockwise. 90 ° CW Rotates the image 90 ° clockwise. 180 ° Rotates the image 180 ° A BOUT S CANNER Displays version information for the KODAK Driver.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-26 Using KODAK Drivers with Windows Applications — PC B RIGHTNESS Adjusts the brightness level of the entire image. NOTE : Refer to “Change Brightness” earlier in this chapter for additional information on this option.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using KODAK Drivers with Windows Applications — PC 9-27 scan the cropped area into your application, resulting in a smaller image size. NOTES: To change the size of an existing selected area, drag a handle to make the rectangle bigger or smaller.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-28 Using KODAK Drivers with Windows Applications — PC M AGNIFICATION A DJUSTMENT Adjusts the magnification of the image, allowing you to ensure that as many pixels of the imager as possible are used for your image.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using KODAK Drivers with Windows Applications — PC 9-29 S CAN Produces the final scan of the image at the current settings, closes the KODAK Driver window, and creates an untitled window displaying the scanned image in your application.
.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Appendices 10-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Software License Agreement A-1 Appendix A — Software License Agreement EASTMAN KODAK COMP ANY YOU SHOULD CAREFULLY READ THE FOLLOWING TERMS AND CONDITIONS BEFORE OPENING THE DISKETTE PACKAGE(S).
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . A- 2 Software License Agreement terms and conditions of this Agreement. If you transfer the software, you must at the same time either transfer all copies to the same party or destroy any copies not transferred.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Software License Agreement A-3 THE SOFTWARE IS PROVIDED ‘AS IS’ WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . A- 4 Software License Agreement Some states do not allow the limitation or exclusion of liability for inci- dental or consequential damages, so the above limitation or exclusion may not apply to you.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Warranty B-1 Appendix B — W ARRANTY KODAK Professional RFS 3570 Film Scanner THIS WARRANTY IS LIMITED TO THE UNITED STATES. THIS WAR- RANTY APPLIES ONLY FOR SERVICING EQUIPMENT ORIGINALLY PURCHASED IN THE UNITED STATES.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . B- 2 Warranty sary to replace the entire system, it may be replaced with a remanufactured system.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Warranty B-3 DO NOT RETURN ANY DEFECTIVE EQUIPMENT TO KODAK WITH- OUT PRIOR AUTHORIZATION FROM THE KODAK INFORMATION CENTER (KIC).
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . B- 4 Warranty Such damages for which Kodak will not be responsible include, but are not limited to, loss of revenue or profit, downtime costs, loss of use of the equipment, cost of any substitute equipment, facilities or services or claims of your customers for such damages.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Troubleshooting C-1 No power. POWER light on top front left of Scanner is not on. Power cord loose or not plugged in at one or both ends. Make sure all plugs are securely seated. Power not turned on.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . C- 2 Troubleshooting Macintosh. Computer crashes or you lose files or folders from your Macintosh computer hard disk. You are using System 7.0 or System 7.0.1 and are not using the System Tuner version 1.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Troubleshooting C-3 Spots or other unwanted shapes appear in the image. Defects in film. Substitute another image (if available) or correct the defect(s) while working with the image in Photoshop.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . C- 4 Troubleshooting Monitor image is monochrome. Monochrome monitor in use. Your monitor is not capable of displaying a color image; however, images scanned in color retain all color data and are acquired into your image editing application with all colors intact.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Troubleshooting C-5 There are excessive patterns (noise) in the image. The Scanner is being operated outside its ambient temperature range. (Perhaps the Scanner has been stored or transported at temperatures outside its range.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . C- 6 Troubleshooting A voiding “W ater Spots” or “Bubbles” When Scanning This section describes steps you take to avoid the appearance of un- wanted circular shaped objects — appearing like water spots, dimples, bubbles, or blisters — in scanned images.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Troubleshooting C-7 2. Orient the dust removal tool as shown below, with the label on the tool (and the fiber strip) facing the front of the scanner; in this position the dust removal tool is behind the diffuser.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . C- 8 Troubleshooting Using the Recalibrate Button Follow these steps if bubbles still appear in the scanner image after cleaning the diffuser. 1. Focus the image using the procedure described in Chapter 5 (Macintosh) or 9 (PC).
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Messages D-1 “CALIBRATION COMPLETE! 1. REMOVE the CALIBRATION MASK. 2. INSERT appropriate adapter for the desired film holder. 3. INSERT desired film holder, including film. 4. CLICK OK to continue.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . D- 2 Messages “CALIBRATION PROCEDURE 1. If using 35 mm multi - frame holder, REMOVE the holder and holder adapter. or If using single-frame film holder, REMOVE the holder. 2. INSERT or CONFIRM that the single-frame film holder adapter is in the scanner.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Messages D-3 “Cannot create the buffer for scanning image.” There is not enough storage or memory to complete the operation.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . D- 4 Messages “Cannot locate the SCSI host adapter.” A supported SCSI host adapter is not installed, or if installed is not working properly. If necessary have a technician install a supported host adapter.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Messages D-5 “Could not calibrate scanner.” The Film or Slide holder — with film loaded — has been left in the Scanner. Remove the Holder from the Scanner and try again. An unexpected problem has developed with the Scanner software.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . D- 6 Messages “File Error: Cannot find WINASPI.DLL.” (Appears when using the TWAIN compliant KODAK Driver after selecting the source.) The TWAIN compliant KODAK Driver for ASPI is installed, but a non- ASPI SCSI Host Adapter and not an ASPI compliant host adapter is installed in the PC.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Messages D-7 You have connected the Scanner to a different computer (or to the same computer to which you recently connected an additional SCSI device), and there is now a SCSI ID conflict. Reset the Scanner SCSI ID so that it is different from other devices connected to the computer.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . D- 8 Messages “Firmware download failed. Could not load RFS3570.BIN file.” NOTE: Firmware is downloaded automatically to the Scanner the first time that you try to access the Scanner during each work session.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Messages D-9 “Incorrect Firmware Version. Install the latest KODAK Driver for Adobe Photoshop Software.” The Driver is attempting to download firmware to the Scanner but does not find the files it needs.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . D- 10 Messages “Not enough memory.” There is not enough storage or memory to complete the operation. With a Macintosh Computer, quit Adobe Photoshop and increase its memory size. (Select Photoshop on the Finder.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Messages D-11 “Parity error detected during transfer.” A hardware error has been detected in the cabling or in the Scanner. Verify that all SCSI connections are correct (if necessary turn off all equipment to alter the connections).
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . D- 12 Messages “Required Scanner setup file (RFS3570.TBL for input) not available. Try again. If problem persists, reinstall the driver and try again. If unsuccessful, contact Kodak.” The software Driver is unable to use a required file.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Messages D-13 The SCSI cable is defective. Use another SCSI cable. The Scanner SCSI ID is set improperly. Reset the Scanner SCSI ID so that it is different from other devices connected to the computer.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . D- 14 Messages “This driver may not be compatible with this version of PHOTOSHOP™” The KODAK Driver and your version of Adobe Photoshop are incompatible. Adobe Photoshop version 2.0 or higher is required.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Replacing the Fuse E-1 Appendix E — Replacing the Fuse Always turn off the Scanner and unplug it prior to replacing the fuse. Follow these instructions to replace the fuse when it has blown, or when moving the Scanner from one electrical service to another.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . E- 2 Replacing the Fuse 4. Notice that the fuse cover has a small tab accessible from the plug outlet cavity. Fuse Cover Tab 5. Insert a thin, flat object (like a small screwdriver), beneath the fuse cover tab and twist; the fuse housing pops free.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Replacing the Fuse E-3 7. Lift the tab on the fuse housing and slide out the fuse holder. Lift this tab. FUSE HOLDER 8. Use your thumb and forefinger to pull the fuse from the fuse holder. FUSE 9.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . E- 4 Replacing the Fuse 10. With the fuse facing up, insert the flat end of the fuse holder into the fuse housing, and slide the pieces together until they snap together.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Updating the KODAK Driver F-1 Appendix F — Updating the KODAK Driver This appendix provides information on obtaining and installing an up- dated software driver including: Directions for downloading the software driver electronically from several sources.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-2 Updating the KODAK Driver files by product, version, release date, and so on. Find and download the driver for the product you use. Via the World Wide Web at: “http://www.kodak.com/productInfo/technicalInfo/ driverSupport.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Updating the KODAK Driver F-3 Installing the Software Driver This section describes how to update the driver on your hard disk, either the KODAK Driver for Adobe Photoshop Software (Macintosh) or the KODAK TWAIN Driver.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . F-4 Updating the KODAK Driver Updating the KODAK TWAIN Driver (PC) 1. Complete all steps in “Installing TWAIN Compliant KODAK Driver(s)” i.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Repacking Instructions G-1 Appendix G — Repacking Instructions If you are having difficulties using your KODAK Professional RFS 3570 Film Scanner, please contact a Kodak representative before returning your unit for service.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . G- 2 Repacking Instructions 4. Remove the Film or Slide Holder from the Scanner. 5. Place the Scanner into the plastic bag and then into the original shipping carton. NOTE: The plastic bag is important because it protects the Scanner from dirt and scuffing during shipment.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Problem Report Form H-1 Appendix H — Problem Report Form KODAK Professional RFS 3570 Film Scanner Customer Return Address Name _____________.
.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Optional Equipment & Spare Parts List I-1 KODAK XLS 8650 Digital Printer (raster) Prints 300 pixels per inch, 24-bit color or eight-bit gray scale images up to 8.5 x 12-inches (21.6 x 30.5-cm) to KODAK EKTATHERM XLS print paper or transparencies.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-2 Optional Equipment & Spare Parts List RFS 35 mm Negative Film Holder 871-4263 35 mm Ne ga ti v e Film Holder for use with RFS 35, RFS .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Optional Equipment & Spare Parts List I-3 Software Drivers You may be able to obtain software drivers prepared by companies other than Kod.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-4 Optional Equipment & Spare Parts List NOTE: The Macintosh and PC cables below are also widely available from computer retailers. If you obtain a cable from one of these sources, be certain to obtain a high quality cable with a continuous EMI shield over the cable and connections.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Optional Equipment & Spare Parts List I-5 KODAK Driver for Adobe Photoshop Software (Macintosh), and KODAK TWAIN Driver (PC, 3.
.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Specifications J-1 Appendix J — Specifications KODAK Professional RFS 3570 Film Scanner Power 120 V, 60 Hz, 1.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . J-2 Specifications A/D Accuracy 12-bit A/D conversion Dynamic Range 12-bits per color Color/Gray Levels 24 bits per color pixel 8 bits per mon.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Specifications J-3 Approximate Dimensions 13.25 in. (33.7 cm) wide x 21 in. (53.4 cm) long x 8 in.
.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Glossary K-1 Appendix K — Glossary This section provides brief explanations of terms used in conjunction with the Scanner. Refer to the Index to find additional reference material about the following terms.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . K-2 Glossary KODAK Driver window. The window displayed by the driver in which a preview of one image appears. The window also displays controls that allow you to manipulate the scanning process.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Index 11-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-2 Index 8-bit video card. See Video display card 8-bits per monochrome pixel J-2 12-bit color 1-2, J-2 16-bit video card.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Index 11-3 D Dimensions J-3 Diffuser 5-22, 9-22 to 9-23, C-6 Display. See Monitor Display card. See Video display card Dithered color, monitor 1-2 DOS prompt 7-22, 9-4 Downloading drivers F-1 to F-4 DPI (resolution) Macintosh 5-28 PC 9-28 Drivers.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-4 Index KODAK Professional Film Macintosh 5-27 PC 9-27 KODAK RFS 3570 (menu choice) 3-22, 5-3, 5-23 KODAK XLS 8650 printer I-1 KODAK XLS 86.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Index 11-5 S Safeguards iii to vi Safety specifications J-3 Scan (image) Macintosh 5-5 to 5-23, 5-29 Command 5-16, 5-21 Message D-5 PC 9-16 to.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-6 Index Video display card 1-2 Macintosh 2-2 PC 6-2 View Changes Macintosh 5-16, 5-19, 5-20, 5-30 PC 9-20, 9-25, 9-29 W Warm up time J-1 Warranty B-1 to B-4 Warranty Registration card 2-1, 6-1 Water hazard iv Weight J-3 Windows 6-2, 6-3, 9-4 ASPI host adapter.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Specifications 9-1 Eastman Kodak Company (“Kodak”) reserves the right to change this information without notice.
EASTMAN KODAK COMPANY • ROCHESTER, NY 14650 KODAK Professional RFS 3570 Film Scanner Revised 4-97 Part No. 7C3306 Kodak is a trademark. Printed in U.
An important point after buying a device Kodak RFS 3570 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Kodak RFS 3570 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Kodak RFS 3570 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Kodak RFS 3570 you will learn all the available features of the product, as well as information on its operation. The information that you get Kodak RFS 3570 will certainly help you make a decision on the purchase.
If you already are a holder of Kodak RFS 3570, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Kodak RFS 3570.
However, one of the most important roles played by the user manual is to help in solving problems with Kodak RFS 3570. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Kodak RFS 3570 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
