Instruction/ maintenance manual of the product A42W64AT4 AOC
Go to page of 19
USER’S M ANUAL A42W64AT4 Thank y ou ver y much for choosi ng the Env is ion Seri es Plasma TV. W e recommen d that y ou take a few minut es to read carefull y thr ough this manu al before ins tall ing and using the TV .
0 IMPORTANT SAFETY INSTRUCTION S .................................................................................. ...1 Precautions and Reminders……………………………………………………………………………..2 Features and Fu n ction………………………………………………………….
1 Read before operating equipment 1. Read and follow all instructions. 2. Do not operate this apparatus near water . 3. Do not install near any heat sources s uch as radiators, heat registers, stoves, or other apparatus (including amplifiers ) that produce heat.
2 2 Do not place unit on uneven surfaces. 2 Do not place the TV in confined spaces or in a box when using it. 3 Unplug immediately if t here is any malfunction, like no video, no audio, smoke or a bad odor . 3 Unplug immediately if other foreign materials are put inside TV box or if the TV fell down.
3 2 DO NOT use liquid cleansers or aerosol cleansers to clean the plasma display . Dilute a neutral detergent with water and wipe with a soft cloth or gently cl ean with some absorbent cotton. Remember to unplug the AC mains cord before cleaning the display .
4 42 inch （ 107cm ） Large Screen Flat Panel Plasma Display Panel Resolution: WVGA 852 x 480 Pixels MAX Brightness of Panel: 1500 Cd/m 2 MAX Contrast Ratio of Panel: 10000:1 V iew Angle: Greater than 160 ° Internal TV T uner , Air ： 69 channels Cable ： 135 channels Frequency Range ： 55.
5 ⑦ ⑥ ⑤ ④ ③ ② ① ① MODE Mode: Press to select input signal modes or use as Enter in Menu operation. ② MENU Menu: Press to enter Menu or exit Menu. ③ - VOL + Left: Press to decrease the sound volume level or move Left in Menu operation.
6 POWER KEY 1. Connect TV Cable and Power Cord to this PDP TV Set. 2. Plug Power Cord to your home power outlet. 3. Check front panel LED for proper power connection: Blue color indicates this TV set is powered on; Red color indicates this TV set is in standby state.
7 Please connect this TV Set to other equipment as picture below . Y ou may have many types of equipment as: DVD, VCD, VCR, Set T op Box, X-Box and so on.
8 INPUT CONNECTION OF PC SIGNAL(PC/DVD) Notice: If you see that display abnormalit y in screen, you need to check the cable connection and DVD setup. ● D-SUB 15 Pin: Connect D-SUB signal cable （ VGA cable ） from PC to D-SUB jack at the back of this display .
9 Remote Control Function “ EPG ” Display the st ate, source “ Wide Mode ” Normal, Zoom ,Wide, Cinema dis p la y select “ POWER ” The TV Set turn on /turn off ke y “ MUTE ” Mute the sound “ MENU ” T o enter Menu mode . “ SLEEP ” Select timer into power down st ate.
10 Main Menu Setup Menu 1. Press “MENU” key on remote control or front panel controls to bring up Main Menu. 2. Press “ ” or “ ” to move the curso r up and down the sub menu list. 3. Press “ ” or “ ” to select sub menu item.
11 V ideo Menu . Audio Menu Contrast: Contrast adjustment, 0 ~ 100. Brightness: Brightness adjustment, 0 ~ 100. Color: Color chroma adjustment, 0 ~ 100. Tint: Tint adjustment, 0 ~ 100. Aspect Ratio: Aspect Ratio selection. Normal Zoom Wide Cinema.
12 Feature Menu Parental Control Menu: Controls viewing of rated TV and Movie programs. Note :Need password to change settings. Initial Default password is: 0000. Important : If you have forgotten you r Password Use the code [0711] to enter into the Password Set menu item to change you r password.
13 Closed Captions section 1. Press “CC” key on remote control to select closed captions mode. NTSC TV: Off..CC1 ..CC2 .. … ATSC TV: Off ..CS1 ..CS2.. … 2. Select desired closed caption mode. EPG EPG Message Window TV channel arrangement Analog NTSC channels are Numbered as2.
14 Item Specification Screen size 42 inch plasma display panel Aspect 16 : 9 Display pixels 852 x 480 (WVGA) Effective display size 932 mm x 532 mm Number of color 16.
15 Symptoms Checks Picture freezes in antenna mode. The TV does not react to remote controller commands. • Please ensure the antenna is properly connected. • Please switch off the mains and switch on again. • Re-install the channels if needed. Picture breaks up in DVI mode, especially when a set top box is connected.
16 Some parts of the screen do not light up The plasma TV panel is manufactured using an extremely high level of precision technology, however, sometimes some parts of the screen may be missing picture elements or have luminous spots. This is not a malfunction.
Envision Peripherals Inc. 47490 Seabridge Dr. Fremont, CA 94538 www.AOCdi splay.com Tech Support: 1-888-662-9888.
An important point after buying a device AOC A42W64AT4 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought AOC A42W64AT4 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data AOC A42W64AT4 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, AOC A42W64AT4 you will learn all the available features of the product, as well as information on its operation. The information that you get AOC A42W64AT4 will certainly help you make a decision on the purchase.
If you already are a holder of AOC A42W64AT4, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime AOC A42W64AT4.
However, one of the most important roles played by the user manual is to help in solving problems with AOC A42W64AT4. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device AOC A42W64AT4 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
