Instruction/ maintenance manual of the product 203P AOC
Go to page of 22
41G2001-615-1A 英文.
TABLE OF CONTENTS FOR YOUR SAFETY -------------------------------------------------- 1 SAFETY PRECAUTIONS -------------------------------------- 2 SPECIAL NOTES ON LCD MONITORS ------------------- 3 B.
2 Before operating the monitor, pleas e read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED.
PRECAUTIONS z Do not use the monitor near water, e.g. near a bathtub, w ashbowl, kitchen sink, laundry tub, sw imming pool or in a we t basement. z Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and c ause serious damage to the appliance.
SPECIAL NOTES ON LCD MONITORS The following symptoms are normal w ith LCD monitor and do not indicate a problem. NOTES • Due to the nature of the fluoresc ent light, the screen may flicker during initial use. Turn off the Power Sw it ch and then turn it on again to make sure the flicker disappears.
INSTALLATION INSTRUCTIONS SWIVEL BASE Install Remove Figure 1 Installing and Removing the Swivel Base POWERCORD Pow er Source: 1. Make sure that the power cord is the correct type required in y our area.
CONTROLS AND CONNECTORS VIDEO CABLE Connecting the signal Cable : Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the co mputer’s D-Sub port. Connect one end of the 24-pin DVI cabl e to the back of the monitor and connect the other end to the computer’s DVI port.
ADJUSTING THE VIEWING ANGLE • For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’ s angle to your ow n preference. • Hold the stand so y ou do not t opple the monitor w hen you change the monitor’s angle.
OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the moni tor on or off. The other control buttons are located on the front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjus ted to your personal preferences.
FRONT PANEL CONTROL • Pow er Button / Powe r Indicator: Press this button to turn the monitor ON or OFF. Blue — Power On mode. Orange — Off mode. • MENU / ENTER : Activate OSD menu when OSD is OFF or activate/de-activate adjustment function w hen OSD is ON or Exit OS D menu when in Volume Adjust OSD status.
HOW TO ADJUST A SETTING 1. Press the MENU-button to activate the OSD window . 2. Press < or > to navigate through t he functions. Once the desired function is highlighted, press t he MENU-button to activate it. If the function selected has a sub-menu, press < or > again to navigate through the sub- menu functions.
ADJUSTING THE PICTURE The descriptions for function control LEDS Main Menu Item Main Menu Icon Sub Menu Item Sub Menu Icon Description Reset Value Contrast Contrast from Digital- register.
H. Position Adjust the horizontal position of the OSD. 50 V. Position Adjust the verticalposition of the OSD. 50 OSD Setup OSD Timeout Adjust the OSD timeout. 10 English N/A Set OSD display language to English. Deutsch N/A Set OSD display language to German.
PLUG AND PLAY Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host sy stem of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities.
TECHNICAL SUPPORT (FAQ) Problem & Question Possible Solution Power LED is not on *Check if the Power Sw itch is in the ON position *Power Cord should be connected No Plug & Play *Check if the .
Screen image is not centered or sized properly. *Adjust pixel frequency (CLOCK) and FOCUS or press hot-key (AUTO). Picture has color defects (white does not look w hite) *Adjust RGB color or select color temperature.
ERROR MESSAGE & POSSIBLE SOLUTION CABLE NOT CONNECTED : 1. Check that the signal-cable is pr operly connected , If the connector is loose, tighten the connector’s screws.
APPENDIX SPECIFICATIONS Driving system TFT Color LCD LCD Panel Size 51cm(20") Pixel pitch 0.255mm( H )x 0.255mm( V ) Viewable angle 170 ° (H) 170 ° (V) R,G,B Analog Interface Video Digital interface H-Frequency 30KHz – 80Hz V-Frequency 55-75Hz Display Colors 16.
Switch • Source • Auto Config / Exit • ∧ / Brightness • ∨ / Contrast • Menu / Enter • Power Button External Controls: Functions • Contrast • Brightness • Focus • Clock • H.
Preset Display Modes STANDA RD RESOLUTION HORIZONTA L FREQUENCY(KHZ) VERTICA L FREQUENCY(HZ) IBM DOS 720 × 400 31.47 70.0 640 × 480 31.47 60.0 VGA 640 × 480 37.50 75.0 800 × 600 37.879 60.0 SVGA 800 × 600 46.875 75.00 1024 × 768 48.363 60.0 1024 × 768 56.
CONNECTOR PIN ASSIGNMENT 15 6 10 11 15 15 - Pin Color Display Signal Cable PIN NO. DESCRIPTION PI N NO. DESCRIPTION 1. Video-Red 9. +5V 2. Video-Green 10. Detect Cable 3. Video-Blue 11. NC 4. NC 12. DDC-Serial data ` Ground 13. H-sync 6. GND-R 14. V-sync 7.
21 41G2001-615-1A 英文.
An important point after buying a device AOC 203P (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought AOC 203P yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data AOC 203P - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, AOC 203P you will learn all the available features of the product, as well as information on its operation. The information that you get AOC 203P will certainly help you make a decision on the purchase.
If you already are a holder of AOC 203P, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime AOC 203P.
However, one of the most important roles played by the user manual is to help in solving problems with AOC 203P. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device AOC 203P along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
