Instruction/ maintenance manual of the product W10189719A KitchenAid
Go to page of 12
MICROWAVE HOOD COMBINATION INSTALLATION INSTRUCTIONS MICROWAVE HOOD COMBINATION SAFETY This pro duct is suitable for us e above electric or gas cooking pr oducts up to and including 36" (91. 4 cm ) wide. For gas cooktop , we recommend that the combined cookin g surfa ce rating does not exceed 55,000 BTU/ hr .
2 INSTALLATION REQUIREMENTS The microwave oven is set for r ecirculation installation. For exte rnal (wall or roof) venting, se e “V enting Design Specificatio ns” sect ion. Tools and Parts T ools Needed Gather the r equir ed tools and part s befor e starting installation.
3 Installation Dimensions NOTE: The grounded 3 prong outlet must be inside the upper cabinet. See “Electrical Requir ements” section. * 33" (83.2 cm) is typical for 69" (175.3 cm) i nstallation height. Exact dimension may vary depending on type of range/cooktop below .
4 INSTALLATION INSTRUCTIONS Remove Mounting Plate NOTE: T o avoid possible damage to the work surface, cover the work surface. 1. Remove any remaining co ntents from the microwave ov en cavity . 2. Remove the mounting plate by peeling off the strips of tape that attach it to the back of the microw ave oven, and set the mounting plate aside.
5 holes should align with mounti ng holes in the vent opening, as shown in inset. 4. Secur e vent deflector with 2 mounti ng screws (1 on eac h end). 5. Replace vent scr een . W all V enting Installation Only T o Remove W all Damper V ent Cover: 1. Locate the wall damper vent cover on the back of the microw ave oven.
6 Locate Wall Stud(s) NOTE: If no wall studs exist within the cabin et opening, do not install the microwave oven. See illustrat ions in “Possible W all Stud Configurati ons.” 1. Using a stud finder , locate the ed ges of the wall stud(s) wit hin the opening.
7 Mark Rear Wall The microwave oven must be inst alled on a minimum of 1 wall stud, preferably 2 , using a minimum of 1 lag screw , preferably 2. 1. Using measuring tape, find an d clearly mark the vertical centerlin e of the open ing. A. Centerline 2.
8 Attach Mounting Plate to Wall NOTE: Secure the mounting plate to the wall at both bottom cor ner holes drill ed into the wall studs and/or drywall using either 1/4-20 x 3" r ound-he ad bolts and toggle nuts or 1 /4 x 2" lag screws.
9 5. Cut the 1 ¹⁄₂ " (3.8 cm) diameter hole at the circu lar shaded ar ea “G” on the template. This hole is for the power supply cor d. NOTE: If upper cabinet is metal, the supply cord bushing needs to be installed ar ound the supply cor d hole, as shown.
10 For Roof V enting Installation Only 1. Insert damper assembly through th e cabinet cutou t so that the long tab of the damper assembly slid es into the slot on the left side of the damper vent opening, as shown. Then secu re with mounting scr ew . NOTE: The screw cannot be instal led if the damper assembly is not positioned as shown.
11 VENTING DESIGN SPECIFICATIONS This section is i ntended fo r ar chitectural designer and builder/contractor refer ence only . NOTES: ■ V ent materials needed for instal lation are not pr ovided with microw ave hood. ■ W e do not recommend using a flexible metal vent.
Recommended V ent Length A 3 ¹⁄₄ " x 10 " (8.3 x 25.4 cm) r ectangular or 6 " (15.2 cm) ro und vent should be used. The total lengt h of the vent syste m including stra ight vent, elbow(s), transitions and wall or roof caps must not exc eed the equivalent of 140 ft (42.
An important point after buying a device KitchenAid W10189719A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought KitchenAid W10189719A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data KitchenAid W10189719A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, KitchenAid W10189719A you will learn all the available features of the product, as well as information on its operation. The information that you get KitchenAid W10189719A will certainly help you make a decision on the purchase.
If you already are a holder of KitchenAid W10189719A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime KitchenAid W10189719A.
However, one of the most important roles played by the user manual is to help in solving problems with KitchenAid W10189719A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device KitchenAid W10189719A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
